CoChat

Realizing Formation and Decomposition of Li2O2 on Its Own Surface with a Highly Dispersed Catalyst for High Round-Trip Efficiency Li-O2 Batteries

Open access
Song, Li-Na, Zou, Lian-Chun, Wang, Xiao-Xue, Luo, Nan, Xu, Ji-Jing, Yu, Ji-Hong · 2019 · iScience

The DOI matches its Crossref record; 40 of the 40 references it cites were found in a registry or an index; none of the 21 sources its claims cite is checked for support yet.

Abstract

The rapid and effective formation and decomposition of Li 2 O 2 during cycling is crucial to solve the problems associated with the practical limitation of lithium-oxygen (Li-O 2 ) batteries. In this work, a highly dispersed electrocatalyst with Ru nanoclusters inside the special organic molecular cage (RuNCs@RCC3) through a reverse double-solvent method for Li-O 2 batteries has been proposed for the first time. This RuNCs@RCC3 shows an effective catalyst enabling reversible formation and decomposition of the Li 2 O 2 at the interface between the Li 2 O 2 and the liquid electrolyte, rather than the sluggish solid-solid interface reactions on commonly used solid catalysts. As a result, the Li-O 2 cells with RuNCs@RCC3 show enhanced electrochemical performance, including low overpotential (310 mV at a current density of 100 mA g −1 ), high specific capacity (15,068 mAh g −1 ), good rate capability (1,800 mAh g −1 at a current density of 2.8 A g −1 ), and especially superior cycle stability up to 470 cycles.

Overview

CoChat Summary

TL;DR

The paper reports a highly dispersed Ru nanocluster catalyst encapsulated in an organic molecular cage (RuNCs@RCC3) for Li-O2 batteries, enabling Li2O2 formation and decomposition at the Li2O2/liquid-electrolyte interface rather than only at solid-solid interfaces. The resulting cells show low overpotential, high capacity, improved rate capability, and long cycle stability.

Key findings

  • Li-O2 cells with RuNCs@RCC3 achieved a low overpotential of 310 mV at 100 mA g−1, a high specific capacity of 15,068 mAh g−1, rate capability of 1,800 mAh g−1 at 2.8 A g−1, and cycle stability up to 470 cycles.
  • Compared with RuNPs and no catalyst, RuNCs@RCC3 gave a discharge voltage higher by ∼123 mV and ∼178 mV, respectively, and a charge voltage lower by ∼383 mV and ∼920 mV, respectively.
  • Discharge capacities were 15,068 mAh g−1 with RuNCs@RCC3 versus 11,536 mAh g−1 with RuNPs and 6,066 mAh g−1 without catalyst; the cell without catalyst had coulombic efficiency of only ca. 35.2%, and at 1,000 mA g−1 the RuNCs@RCC3 cell still reached 2,893 mAh g−1.
  • Morphology differed: without catalyst, disk-like Li2O2 particles (∼200 nm) covered the cathode, whereas with RuNCs@RCC3, micrometer-sized flower-like Li2O2 formed (2 μm and 10–20 μm); discharge terminal voltage remained >2 V for 470 cycles with RuNCs@RCC3, versus <2 V after 315 cycles with RuNPs and 288 cycles with pristine CNT.

Methods

  • The RCC3 cage was synthesized by reducing CC3R with NaBH4, and Ru nanoclusters were encapsulated inside RCC3 via a reverse double-solvent method; characterization included FESEM, TEM, FTIR, PXRD, N2 adsorption-desorption, XPS, NMR, mass spectrometry, and elemental analysis.
  • Li-O2 cells used a carbon nanotube cathode, lithium anode, and TEGDME/CH2Cl2 (2:1)/LiTFSI electrolyte; specific capacities and current densities were calculated based on total carbon mass on the cathode (0.45 mg cm−2), with comparisons against RuNPs and no catalyst.
  • Electrochemical testing included galvanostatic discharge-charge, rate capability, electrochemical impedance spectroscopy, capacity-limited cycling, and post-mortem FESEM, XRD, titration, Karl Fischer titration, NMR, and FTIR analyses; detailed methods are in the accompanying Transparent Methods supplemental file.

Limitations

  • Stated in the paper: differential electrochemical mass spectroscopy (DEMS) was not available for quantitative analysis of by-products because of limited laboratory conditions.
  • Evident from the text: detailed experimental procedures are not given in the main article and are instead relegated to the Transparent Methods supplemental file.
  • Evident from the text: the 470-cycle stability test was capacity-limited to 500 mAh g−1 at 200 mA g−1, and the high-capacity test at 5,000 mAh g−1 remained for more than 14 cycles, so full-capacity long-term cycling is not demonstrated.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1016/j.isci.2019.03.013

Cites

40 of 40 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Graphical abstract
Graphical abstract CC BY · PubMed Central
Figure 1 Scheme for the Fabrication of RuNCs@RCC3 (A) Synthesis of the CC3R cage by a [4 + 6] cycloimination and the reduction of CC3R to RCC3 cage by NaBH4. (B) Schematic illustration of the encapsulation of Ru nanoclusters inside the RCC3 matrix using a reverse double-solvent approach.
Figure 1 Scheme for the Fabrication of RuNCs@RCC3 (A) Synthesis of the CC3R cage by a [4 + 6] cycloimination and the reduction of CC3R to RCC3 cage by NaBH4. (B) Schematic illustration of the encapsulation of Ru nanoclusters inside the RCC3 matrix using a reverse double-solvent approach.CC BY · PubMed Central
Figure 2 Morphological and Structural Characterization of RuNCs@RCC3 (A) FESEM image of RCC3. See also Figure S7. (B and C) Scanning electron microscopic (B) and TEM (C) images of RuNCs@RCC3. See also Figures S8 and S9. Scale bars, 1 μm in (A), 2 μm in (B) and 500 nm in (C). (D–F) FTIR patterns (D), PXRD patterns (E), and N2 adsorption-desorption isotherms (F) of RCC3 and RuNCs@RCC3. See also Figures S2 and S10. (G and H) Ru 3d XPS spectrum (G) and N 1s XPS spectrum (H) of the RuNCs@RCC3. (I) 1H NMR spectra of RCC3 and RuNCs@RCC3. See also Figure S4.
Figure 2 Morphological and Structural Characterization of RuNCs@RCC3 (A) FESEM image of RCC3. See also Figure S7. (B and C) Scanning electron microscopic (B) and TEM (C) images of RuNCs@RCC3. See also Figures S8 and S9. Scale bars, 1 μm in (A), 2 μm in (B) and 500 nm in (C). (D–F) FTIR patterns (D), PXRD patterns (E), and N2 adsorption-desorption isotherms (F) of RCC3 and RuNCs@RCC3. See also Figures S2 and S10. (G and H) Ru 3d XPS spectrum (G) and N 1s XPS spectrum (H) of the RuNCs@RCC3. (I) 1H NMR spectra of RCC3 and RuNCs@RCC3. See also Figure S4.CC BY · PubMed Central
Figure 3 Electrochemical Performance and Characterization of Discharged Products (A) First charge-discharge curves of lithium-oxygen (Li-O2) cells at a current density of 100 mA g−1, and a specific capacity limit of 500 mAh g−1. (B) Photographs of the pristine electrolyte (left), RuNCs@RCC3 (middle), and RuNPs/RCC3 (right) catalysts in CH2Cl2/TEGDME (v/v, 1/2) at different stages (Cm = 6.67 mg/mL). (C) An electrochemical mechanism for the aggregation of Li2O2 on the surface of the CNT with RuNCs@RCC3, versus without catalyst. (D and E) The rate capability (D) of the Li-O2 cells with three types of catalysts at different current densities. Galvanostatic discharge and recharge curves (E) of the Li-O2 cells with three kinds of catalysts at a current density of 100 mA g−1. See also Figures S12 and S13. (F and G) FESEM image of the discharged CNT cathode without catalyst (F) and with RuNCs@RCC3 (G) at a current density of 200 mA g−1 and a specific capacity of 2,000 mAh g−1. The inset of (G) represents the corresponding enlarged FESEM image. See also Figure S14.
Figure 3 Electrochemical Performance and Characterization of Discharged Products (A) First charge-discharge curves of lithium-oxygen (Li-O2) cells at a current density of 100 mA g−1, and a specific capacity limit of 500 mAh g−1. (B) Photographs of the pristine electrolyte (left), RuNCs@RCC3 (middle), and RuNPs/RCC3 (right) catalysts in CH2Cl2/TEGDME (v/v, 1/2) at different stages (Cm = 6.67 mg/mL). (C) An electrochemical mechanism for the aggregation of Li2O2 on the surface of the CNT with RuNCs@RCC3, versus without catalyst. (D and E) The rate capability (D) of the Li-O2 cells with three types of catalysts at different current densities. Galvanostatic discharge and recharge curves (E) of the Li-O2 cells with three kinds of catalysts at a current density of 100 mA g−1. See also Figures S12 and S13. (F and G) FESEM image of the discharged CNT cathode without catalyst (F) and with RuNCs@RCC3 (G) at a current density of 200 mA g−1 and a specific capacity of 2,000 mAh g−1. The inset of (G) represents the corresponding enlarged FESEM image. See also Figure S14.CC BY · PubMed Central
Figure 4 Cycle Stability and Characterization of Charged Products (A–C) FESEM images of the recharged CNT cathode with RuNCs@RCC3 at a current density of 200 mA g−1 and charge capacities of 500 (A), 1,000 (B), and 2,000 mAh g−1 (C). Insets in (A–C) show the corresponding enlarged FESEM images. (D) FESEM image of the recharged CNT cathode with RuNPs at a current density of 200 mA g−1 with a charge capacity of 1,000 mAh g−1. (E and F) Schematic of the Li2O2 oxidation mechanism in electrolyte with RuNCs@RCC3 (E) and without catalyst (F). (G) Variation of the terminal voltage upon the discharge of the Li-O2 cells at a current density of 200 mA g−1 and a specific capacity limit of 500 mAh g−1 with three types of catalysts. See also Figure S19.
Figure 4 Cycle Stability and Characterization of Charged Products (A–C) FESEM images of the recharged CNT cathode with RuNCs@RCC3 at a current density of 200 mA g−1 and charge capacities of 500 (A), 1,000 (B), and 2,000 mAh g−1 (C). Insets in (A–C) show the corresponding enlarged FESEM images. (D) FESEM image of the recharged CNT cathode with RuNPs at a current density of 200 mA g−1 with a charge capacity of 1,000 mAh g−1. (E and F) Schematic of the Li2O2 oxidation mechanism in electrolyte with RuNCs@RCC3 (E) and without catalyst (F). (G) Variation of the terminal voltage upon the discharge of the Li-O2 cells at a current density of 200 mA g−1 and a specific capacity limit of 500 mAh g−1 with three types of catalysts. See also Figure S19.CC BY · PubMed Central
Figure 5 Cathode Morphology upon Cycling (A–F) FESEM images of the recharged CNT cathode without catalyst at a current density of 200 mA g−1 and a charge capacity of 1,000 mAh g−1 after the fifth recharging (A) and the 20th recharge (B). FESEM images of the recharged CNT cathode with RuNPs at a current density of 200 mA g−1 and a charge of 1,000 mAh g−1 after the fifth(C) and the 20th recharge (D). FESEM images of the recharged CNT cathode with RuNCs@RCC3 at a current density of 200 mA g−1 and a charge capacity of 1,000 mAh g−1 after the fifth recharge (E) and the 20th recharge (F). (G) 1H NMR spectra of the CNT cathodes without catalyst or with RuNCs@RCC3 after the fifth and 20th recharge. The spectra for TEGDME, HCO2Li, and CH2CO2Li are also shown for reference. See also Figure S20.
Figure 5 Cathode Morphology upon Cycling (A–F) FESEM images of the recharged CNT cathode without catalyst at a current density of 200 mA g−1 and a charge capacity of 1,000 mAh g−1 after the fifth recharging (A) and the 20th recharge (B). FESEM images of the recharged CNT cathode with RuNPs at a current density of 200 mA g−1 and a charge of 1,000 mAh g−1 after the fifth(C) and the 20th recharge (D). FESEM images of the recharged CNT cathode with RuNCs@RCC3 at a current density of 200 mA g−1 and a charge capacity of 1,000 mAh g−1 after the fifth recharge (E) and the 20th recharge (F). (G) 1H NMR spectra of the CNT cathodes without catalyst or with RuNCs@RCC3 after the fifth and 20th recharge. The spectra for TEGDME, HCO2Li, and CH2CO2Li are also shown for reference. See also Figure S20.CC BY · PubMed Central
Figure 6 The Morphology and Crystallinity of the Discharged Product upon Cycling (A–D) FESEM images of the fifth (A) and the 20th (B) discharged CNT cathodes without catalyst at a current density of 200 mAh g−1 and a specific capacity of 1,000 mAh g−1. FESEM images of the fifth (C) and the 20th (D) discharged CNT cathodes with RuNCs@RCC3 at a current density of 200 mA g−1 and a specific capacity of 1,000 mAh g−1. Insets in (C and D) show the corresponding enlarged FESEM images. (E and F) PXRD patterns of the discharge products on the CNT cathodes without catalyst (E) and with RuNCs@RCC3 (F). See also Figure S17.
Figure 6 The Morphology and Crystallinity of the Discharged Product upon Cycling (A–D) FESEM images of the fifth (A) and the 20th (B) discharged CNT cathodes without catalyst at a current density of 200 mAh g−1 and a specific capacity of 1,000 mAh g−1. FESEM images of the fifth (C) and the 20th (D) discharged CNT cathodes with RuNCs@RCC3 at a current density of 200 mA g−1 and a specific capacity of 1,000 mAh g−1. Insets in (C and D) show the corresponding enlarged FESEM images. (E and F) PXRD patterns of the discharge products on the CNT cathodes without catalyst (E) and with RuNCs@RCC3 (F). See also Figure S17.CC BY · PubMed Central

Verification

Claims the paper makes

0 Valid · 0 Not valid · 11 Not checked · 0 Own results and interpretations

16 references still to check

A free account verifies the references that are still open.

Verify all 16 references — free account
  • It may state two separate claims as one. 5
  • Probably not a substantial claim. 6

Create a free account to see these claims.

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

Each contradiction between two passages listed here was confirmed by an independent check.

2 of 2

Citations

Cites

Show all 40 references

Cited by

See all 34

Metadata

Authors
Song, L.-N., Zou, L.-C., Wang, X.-X., Luo, N., Xu, J.-J., & Yu, J.-H.
Affiliations
Jilin University (CN)
Corresponding author
Xu, Ji-Jing
Venue
iScience
Publisher
Elsevier BV
Published
2019-04
Volume
14
Pages
36-46
ISSN
2589-0042 (ISSN-L)
OpenAlex
W2921114080
Cited by
34
References
40
Citations by year
2026: 4 · 2025: 2 · 2024: 1 · 2023: 6 · 2022: 11 · 2021: 5 · 2020: 5
FWCI
1.90
Type
journal article
Language
en
Open access
Licence
Locations
  • iScience (publishedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • Europe PMC (PubMed Central) (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
Funders
  • National Natural Science Foundation of China (51771177, 21571075, 21621001, 21835002, 21673220)
  • JLU Science and Technology Innovative Research Team
  • Jilin Province (JJKH20190113KJ)
  • Jilin Province Science and Technology Development (20190303104SF)
  • Jilin University (SXGJSF2017-3)
Topics
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced Battery Materials and Technologies
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
  • Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
Keywords
lithium-oxygen batteries, Li2O2 formation and decomposition, ruthenium nanoclusters, round-trip efficiency, electrode-electrolyte interface, overpotential, cycling stability

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

A language model drew the claims from the paper on 2026-11-20, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-11-20 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Realizing Formation and Decomposition of Li2O2 on Its Own Surface with a Highly Dispersed Catalyst for High Round-Trip Efficiency Li-O2 Batteries. https://app.cochat.ai/papers/10.1016/j.isci.2019.03.013
The paper
Song, L.-N., Zou, L.-C., Wang, X.-X., Luo, N., Xu, J.-J., & Yu, J.-H. (2019). Realizing Formation and Decomposition of Li2O2 on Its Own Surface with a Highly Dispersed Catalyst for High Round-Trip Efficiency Li-O2 Batteries. iScience. https://doi.org/10.1016/j.isci.2019.03.013

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.