The DOI matches its Crossref record; 30 of the 30 references it cites were found in a registry or an index.
Environmental assessment of additive manufacturing in the automotive industry
Open accessAbstract
3D-printing, also known as Additive Manufacturing (AM), is an emerging technology with suggested potential to decrease environmental impacts in the manufacturing industry. Potential benefits from implementing the technology include reduced product weight, transportation and material losses, as well as improved functionality and possibility for printing of spare parts. Possible drawbacks are increased energy use in production and the slow printing process. As the technology is expected to grow significantly, it is important to assess potential environmental effects of implementation. In this study a Life Cycle Assessment (LCA) is used in the case of Powder Bed Fusion (PBF) of the metal parts of an engine in a light distribution truck. Conventional manufacturing is compared to scenarios with 3D-printing, one representing the present state of development of 3D-printing technology and one representing a possible future state. The results show that, in the future case, PBF potentially improves life cycle environmental performance by redesigning components for weight reduction. However, a clean electricity source was required as well as technological development allowing for printing of large components, with low-impact raw materials. When instead assessing AM in its present state of development, results showed only moderate or negligible environmental improvements. To achieve the future potential environmental benefits from AM it is important to use clean electricity and to develop the technology to be able to use low-impact feedstock materials such as low-alloy steel (avoiding materials based on e.g. nickel). Industries implementing AM should seek to exploit the benefits of the technology, such as weight reduction and functionality improvements as well as the potential offered for printing spare parts for remanufacturing and repairing.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing and sustainability: an exploratory study of the advantages and challenges
Ford, S., & Despeisse, M. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2016.04.150 · Cited by 1,889
The Eco-indicator 99 A damage oriented method for Life Cycle Impact Assessment Methodology Report
Goedkoop, M. J. (1999) · Medical Entomology and Zoology · Cited by 1,022
Selective laser melting of aluminium components
Louvis, E., Fox, P., & Sutcliffe, C. J. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.09.019 · Cited by 933
Global Trends in Renewable Energy Investment 2015
Kreibiehl, S. (2015) · Energy Security, Technology and Sustainability Challenges Across the Globe,38th IAEE International Conference,May 25-27, 2015 · Cited by 818
Huang, R., Riddle, M., Graziano, D., Warren, J., Das, S., Nimbalkar, S., Cresko, J., & Masanet, E. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2015.04.109 · Cited by 805
(2013) · Medical Entomology and Zoology · Cited by 690
Environmental Assessment of Emerging Technologies: Recommendations for Prospective LCA
Arvidsson, R., Tillman, A., Sandén, B. A., Janssen, M., Nordelöf, A., Kushnir, D., & Molander, S. (2018) · Journal of Industrial Ecology · doi:10.1111/jiec.12690 · Cited by 539
Self-citationFundamentals of Selective Laser Melting of alloyed steel powders
Rombouts, M., Kruth, J. P., Froyen, L., & Mercelis, P. (2006) · CIRP Annals · doi:10.1016/s0007-8506(07)60395-3 · Cited by 400
Environmental aspects of laser-based and conventional tool and die manufacturing
Morrow, W. R., Qi, H., Kim, I., Mazumder, J., & Skerlos, S. J. (2007) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2005.11.030 · Cited by 380
Kellens, K., Baumers, M., Gutowski, T. G., Flanagan, W., Lifset, R., & Duflou, J. R. (2017) · Journal of Industrial Ecology · doi:10.1111/jiec.12629 · Cited by 310
Dawes, J., Bowerman, R., & Trepleton, R. (2015) · Johnson Matthey Technology Review · doi:10.1595/205651315x688686 · Cited by 248
Wenzel, H., Hauschild, M. Z., & Alting, L. (1997) · Cited by 211
Environmental Impacts of Selective Laser Melting: Do Printer, Powder, Or Power Dominate?
Faludi, J., Baumers, M., Maskery, I., & Hague, R. (2017) · Journal of Industrial Ecology · doi:10.1111/jiec.12528 · Cited by 204
Life cycle assessment of municipal waste water systems
Tillman, A.-M., Svingby, M., & Lundström, H. (1998) · The International Journal of Life Cycle Assessment · doi:10.1007/bf02978823 · Cited by 194
Self-citationRapid prototyping: energy and environment in the spotlight
Mognol, P., Lepicart, D., & Perry, N. (2006) · Rapid Prototyping Journal · doi:10.1108/13552540610637246 · Cited by 185
Note on the Rate and Energy Efficiency Limits for Additive Manufacturing
Gutowski, T., Jiang, S., Cooper, D., Corman, G., Hausmann, M., Manson, J., Schudeleit, T., Wegener, K., Sabelle, M., Ramos‐Grez, J., et al. (2017) · Journal of Industrial Ecology · doi:10.1111/jiec.12664 · Cited by 158
Huang, R., Riddle, M. E., Graziano, D., Das, S., Nimbalkar, S. U., Cresko, J., & Masanet, E. R. (2017) · Journal of Industrial Ecology · doi:10.1111/jiec.12641 · Cited by 123
Walachowicz, F., Bernsdorf, I., Papenfuss, U., Zeller, C., Graichen, A., Navrotsky, V., Rajvanshi, N., & Kiener, C. (2017) · Journal of Industrial Ecology · doi:10.1111/jiec.12637 · Cited by 117
Evaluating Eco‐Efficiency of 3D Printing in the Aeronautic Industry
Mami, F., Revéret, J., Fallaha, S., & Margni, M. D. (2017) · Journal of Industrial Ecology · doi:10.1111/jiec.12693 · Cited by 95
Dhingra, R., & Das, S. (2014) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2014.08.107 · Cited by 90
Cost- and energy-efficient manufacture of gears by laser beam melting
Kamps, T., Lutter-Günther, M., Seidel, C., Gutowski, T. G., & Reinhart, G. (2018) · CIRP journal of manufacturing science and technology · doi:10.1016/j.cirpj.2018.01.002 · Cited by 87
Priarone, P. C., Ingarao, G., Lorenzo, R. D., & Settineri, L. (2016) · Journal of Industrial Ecology · doi:10.1111/jiec.12523 · Cited by 83
Liu, Z., Jiang, Q., Cong, W., Li, T., & Zhang, H. (2017) · International Journal of Environmental Science and Technology · doi:10.1007/s13762-017-1622-6 · Cited by 73
Holmström, J., & Gutowski, T. G. (2017) · Journal of Industrial Ecology · doi:10.1111/jiec.12580 · Cited by 67
Charting the Environmental Dimensions of Additive Manufacturing and 3D Printing
Baumers, M., Duflou, J. R., Flanagan, W. P., Gutowski, T. G., Kellens, K., & Lifset, R. (2017) · Journal of Industrial Ecology · doi:10.1111/jiec.12668 · Cited by 67
Life cycle assessment-based selection of a sustainable lightweight automotive engine hood design
Sun, X., Liu, J., Lü, B., Zhang, P., & Zhao, M. (2017) · The International Journal of Life Cycle Assessment · doi:10.1007/s11367-016-1254-y · Cited by 53
Additive Manufacturing of Steel Alloys Using Laser Powder-Bed Fusion
Jamshidinia, M., sadek, A. A., Wang, W., & Kelly, S. M. (2015) · AM&P Technical Articles · doi:10.31399/asm.amp.2015-01.p020 · Cited by 45
Environmental analysis of SLM and SLS manufacturing processes
Kellens, K., Dewulf, W., Deprez, W., Yasa, E., & Duflou, J. R. (2010) · Lirias · Cited by 39
Lavery, N., Jarvis, D. J., Brown, S. G. R., Adkins, N. J. E., & Wilson, B. P. (2012) · The International Journal of Life Cycle Assessment · doi:10.1007/s11367-012-0478-8 · Cited by 23
3D Printing and Industrial Ecology
Lifset, R. (2017) · Journal of Industrial Ecology · doi:10.1111/jiec.12669 · Cited by 15
Cited by
du Plessis, A., Yadroitsava, I., & Yadroitsev, I. (2020) · Materials & Design · doi:10.1016/j.matdes.2019.108385 · Cited by 712
Chen, L.-Y., Liang, S.-X., Liu, Y., & Zhang, L.-C. (2021) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2021.100648 · Cited by 603
Role of additive manufacturing applications towards environmental sustainability
Javaid, M., Haleem, A., Singh, R. P., Suman, R., & Rab, S. (2021) · Advanced Industrial and Engineering Polymer Research · doi:10.1016/j.aiepr.2021.07.005 · Cited by 419
Environmental and economic assessment on 3D printed buildings with recycled concrete
Han, Y., Yang, Z., Ding, T., & Xiao, J. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.123884 · Cited by 322
Colorado, H. A., Velásquez, E. I. G., & Monteiro, S. N. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.04.062 · Cited by 320
Metadata
- Authors
- Böckin, D., & Tillman, A.-M.
- Venue
- Journal of Cleaner Production
- Publisher
- Elsevier BV
- Published
- 2019-07
- Volume
- 226
- Pages
- 977-987
- ISSN
- 0959-6526 (ISSN-L)
- OpenAlex
- W2937244939
- Cited by
- 307
- References
- 30
- FWCI
- 14.65
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.