The DOI matches its Crossref record; 41 of the 43 references it cites were found in a registry or an index.
Microstructure evolution and corrosion behavior of dissimilar 304/430 stainless steel welded joints
Abstract
Abstract Microstructure and corrosion behavior of dissimilar welds between austenitic stainless steel AISI 304 and ferritic stainless steel AISI 430 were investigated. The phase evolution within each weld was analyzed using thermodynamics calculation and electron back-scattered diffraction (EBSD). Results indicated that the welded joints were mainly composed of martensite and ferrite phases. Thermodynamic calculations show that, during the high temperature phase transformation process, the high-temperature ferrite transforms into austenite to form a mixed state. This austenite further transforms into martensite during the following high rate cooling process. It was also found that increasing the melted-in AISI 304 portion in dissimilar welds led to an increase in the austenite portion at high temperature. This resulted in more portions of martensite being present in the weld at the room temperature. Potentiodynamic polarization curves showed that the corrosion resistance of welded joint decreased with increasing fusion ration of AISI 304, and then increased with further increase in fusion ratio. The initial decrease of corrosion resistance could be attributed to the increased martensite contents and fractions of phase boundaries, and the subsequent increase might contribute to increased Cr contents and decreased fractions of phase boundaries.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“There are some shortcomings in manual testing, such as low confidence and high labor intensity.”
From A New Steel Defect Detection Algorithm Based on Deep Learning (2021) · cites this paper as [3]
Citations
Cites
Calcagnotto, M., Ponge, D., Demir, E., & Raabe, D. (2010) · Materials Science and Engineering: A · doi:10.1016/j.msea.2010.01.004 · Cited by 2,319
Cui, Z., Wang, L., Ni, H., Hao, W., Man, C., Chen, S., Wang, X., Liu, Z., & Li, X. (2017) · Corrosion Science · doi:10.1016/j.corsci.2017.01.016 · Cited by 430
Microstructure and corrosion properties of CrMnFeCoNi high entropy alloy coating
Ye, Q., Feng, K., Li, Z., Lu, F., Li, R., Huang, J., & Wu, Y. (2017) · Applied Surface Science · doi:10.1016/j.apsusc.2016.11.176 · Cited by 408
Cui, Z., Chen, S., Dou, Y., Han, S., Wang, L., Man, C., Wang, X., Chen, S., Cheng, Y. F., & Li, X. (2019) · Corrosion Science · doi:10.1016/j.corsci.2019.02.002 · Cited by 397
Kocijan, A., Merl, D. K., & Jenko, M. (2010) · Corrosion Science · doi:10.1016/j.corsci.2010.11.010 · Cited by 285
EIS study of potentiostatically formed passive film on 304 stainless steel
Mohammadi, F., Nickchi, T., Attar, M. M., & Alfantazi, A. M. (2011) · Electrochimica Acta · doi:10.1016/j.electacta.2011.07.072 · Cited by 284
Dissimilar metal friction welding of austenitic–ferritic stainless steels
Satyanarayana, V. V., Reddy, G. M., & Mohandas, T. (2005) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2004.05.017 · Cited by 254
Kundu, A., & Field, D. P. (2016) · Materials Science and Engineering A · doi:10.1016/j.msea.2016.05.022 · Cited by 232
Hidalgo, J., Findley, K. O., & Santofimia, M. J. (2017) · Materials Science and Engineering A · doi:10.1016/j.msea.2017.03.017 · Cited by 232
Microstructural features of dissimilar welds between 316LN austenitic stainless steel and alloy 800
Sireesha, M., Shankar, V, Albert, S. K., & Sundaresan, S. (2000) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(00)00969-2 · Cited by 223
Research works printed but not linked: 2
- Saunders, 1998, 1
- Houldcroft, 1954, Dilution and uniformity in aluminum alloy weld beads, Br Weld J, 1, 468
Cited by
A New Steel Defect Detection Algorithm Based on Deep Learning
Zhao, W., Chen, F., Huang, H., Li, D., & Cheng, W. (2021) · Computational Intelligence and Neuroscience · doi:10.1155/2021/5592878 · Cited by 259
Wang, C., Yu, J., Yu, Y., Zhao, Y., Zhang, Y., & Han, X. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.05.093 · Cited by 104
Self-citationSelected corrosion of X80 pipeline steel welded joints induced by Desulfovibrio desulfuricans
Wang, Q. L., Zhou, X., Ma, Q., Wu, T., Liu, M., Zhang, M., Li, Z., & Yin, F. (2022) · Corrosion Science · doi:10.1016/j.corsci.2022.110313 · Cited by 69
Laser Dissimilar Welding of AISI 430F and AISI 304 Stainless Steels
Pańcikiewicz, K., Świerczyńska, A., Hućko, P., & Tumidajewicz, M. (2020) · Materials · doi:10.3390/ma13204540 · Cited by 65
Research on Steel Surface Defect Detection Based on YOLOv5 with Attention Mechanism
Shi, J., Yang, J., & Zhang, Y. (2022) · Electronics · doi:10.3390/electronics11223735 · Cited by 61
Self-citationWang, S., Luo, K. C., Sun, T., Li, G., & Cui, J. (2021) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.02.039 · Cited by 52
Tembhurkar, C. K., Kataria, R., Ambade, S. P., Verma, J., Sharma, A., & Sarkar, S. (2021) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-020-05395-4 · Cited by 51
Wang, C., Yu, Y., Zhang, H., Xu, L., Ma, X., Wang, F., & Song, B. (2021) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2021.10.042 · Cited by 47
Self-citationRaj, S., & Biswas, P. (2023) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2023.04.021 · Cited by 46
Kumar, C. M. P., Chandrashekarappa, M. P. G., Kulkarni, R. M., Pimenov, D. Y., & Giasin, K. (2021) · Materials · doi:10.3390/ma14092253 · Cited by 45
Effect of the macro-segregation on corrosion behavior of CrMnFeCoNi coating prepared by arc cladding
Wang, C., Yu, Y., Yu, J., Zhang, Y., Wang, F., & Li, H. (2020) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2020.156263 · Cited by 41
Self-citationShao, Q. C., Shi, Y., Wang, X., Li, M., Chang, Y., Gan, Y., & Cai, B. (2023) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2023.02.061 · Cited by 37
Feng, R., Yang, F., Shao, Y., Roy, K., Lim, J. B. P., & Chen, B. (2024) · Structures · doi:10.1016/j.istruc.2024.106141 · Cited by 36
Pu, Y., Chen, S., Hou, Y., Hou, S., Feng, F., Guo, Z., Zhu, C., & Cheng, Y. F. (2024) · Corrosion Science · doi:10.1016/j.corsci.2024.111947 · Cited by 31
Sengottaiyan, S., Shaisundaram, V. S., Basha, M. S., Deepanraj, B., & Senthilkumar, N. (2025) · Results in Engineering · doi:10.1016/j.rineng.2025.104818 · Cited by 30
Fang, Y., Zhang, Y., Kim, M.-K., Kim, H.-I., No, J., Duan, Z., Yuan, Q. P., & Suhr, J. (2022) · Materials Science and Engineering A · doi:10.1016/j.msea.2022.143891 · Cited by 28
Self-citationLiu, F., Zhou, X., Chen, X., Gong, X., Wu, L., Chen, B., Chen, K., & Tan, C. (2022) · Optics & Laser Technology · doi:10.1016/j.optlastec.2022.108024 · Cited by 25
Ramakrishnan, A., Rameshkumar, T., Rajamurugan, G., Sundarraju, G., & Selvamuthukumaran, D. (2021) · Materials Today Proceedings · doi:10.1016/j.matpr.2021.03.502 · Cited by 25
Rajalingam, P., Rajakumar, S., Sonar, T., & Kavitha, S. (2024) · International Journal of Lightweight Materials and Manufacture · doi:10.1016/j.ijlmm.2024.04.001 · Cited by 24
Cao, J., Wang, Y., Liu, X., Xu, G., Zeng, X., & Wei, K. (2024) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2024.04.236 · Cited by 24
Xu, Y., Wang, R., Sato, Y. S., Tokita, S., Zhao, Y., Yi, Z., & Wu, A. (2024) · Additive manufacturing · doi:10.1016/j.addma.2024.104629 · Cited by 23
Self-citationHedaiat, F., Dehmolaei, R., Khorasanian, M., & Lotfi, B. (2021) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2021.127605 · Cited by 22
Microstructure and corrosion behavior of linear friction welded TA15 and TC17 dissimilar joint
Wang, C., Guo, Q., Shao, M., Zhang, H., Wang, F., Song, B., Ya-juan, J., & Li, H. (2022) · Materials Characterization · doi:10.1016/j.matchar.2022.111871 · Cited by 21
Self-citationAguilar-Ruiz, A. A., Sánchez-Duarte, R. G., Orozco-Carmona, V. M., Dévora‐Isiordia, G. E., Villegas‐Peralta, Y., & Sánchez, J. Á. (2024) · Coatings · doi:10.3390/coatings14101244 · Cited by 20
Selective corrosion behavior of X80 steel heat affected zone by SRB in coastal saline soil
Yu, Y., Xu, J., Liu, B., Chai, T., & Sun, C. (2023) · International Journal of Pressure Vessels and Piping · doi:10.1016/j.ijpvp.2023.104924 · Cited by 19
Self-citationGupta, S. K., Patil, A. P., Rathod, R. C., Tandon, V., & Gupta, A. (2023) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2023.05.107 · Cited by 19
Touileb, K., Djoudjou, R., Hedhibi, A. C., Ouis, A., Benselama, A. S., Albaijan, I., Abdo, H. S., & Samad, U. A. (2022) · Metals · doi:10.3390/met12040635 · Cited by 19
Zhang, T., Liu, W., Dong, B., Wu, Y., Yang, W., Zhao, Y., Fan, Y., & Chen, L. (2021) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2021.125365 · Cited by 17
Self-citationMartin, U., Birbilis, N., Macdonald, D. D., & Bastidas, D. M. (2023) · npj Materials Degradation · doi:10.1038/s41529-023-00406-w · Cited by 16
Corrosion resistance of GTA-welded super duplex and nitronic steel in marine environments
Maurya, A. K., Chhibber, R., & Pandey, C. (2024) · Journal of Materials Science · doi:10.1007/s10853-024-09902-z · Cited by 16
Roy, R., Qu, H. J., Mao, K., & Wharry, J. P. (2025) · Scripta Materialia · doi:10.1016/j.scriptamat.2025.116652 · Cited by 16
Corrosion of Al-Fe self-pierce riveting joints with multiphysics-based modeling and experiments
Bansal, P., Zheng, Z., Pan, B., Meng, Y., Wen, W., Banu, M., Li, J., Carlson, B. E., Shao, C., Wang, P., et al. (2023) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2023.04.014 · Cited by 16
Huang, C.-H., Hou, C.-H., Hsieh, T.-S., Tsai, L., & Chiang, C. (2022) · Science Progress · doi:10.1177/00368504221126795 · Cited by 15
Xiao, H. B., Wang, P., Yi, B., Chen, X., Li, A., Tang, H., Li, W., & Zhang, J. (2020) · Metals · doi:10.3390/met11010006 · Cited by 15
Steel Sheet Defect Detection using Feature Pyramid Network and RESNET
Uraon, P. K., Verma, A., & Badholia, A. (2022) · International Conference on Edge Computing and Applications (ICECAA) · doi:10.1109/icecaa55415.2022.9936318 · Cited by 14
Wang, Z., Zhang, B., Liao, H., Wu, X., Tian, J., & Zhang, Q. (2024) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-024-13191-w · Cited by 12
Kavishwar, S., Bhaiswar, V., Kochhar, S., & Fande, A. W. (2024) · Welding International · doi:10.1080/09507116.2024.2402285 · Cited by 12
Huang, J., Li, S., Zhong, H., Xiao, S., & Li, D. (2021) · steel research international · doi:10.1002/srin.202100541 · Cited by 12
Kovačina, J., Jegdić, B. V., Radojković, B., Marunkić, D. D., Stevanović, S., & Simović, A. R. (2021) · Materials and Corrosion · doi:10.1002/maco.202012241 · Cited by 12
Biswas, A. R., BANERJEE, N., Sen, A., Maity, S. R., Bains, P. S., Sharma, S. K., Kalyani, T., & Abbas, M. A. (2024) · steel research international · doi:10.1002/srin.202400485 · Cited by 11
Wang, Y., Xu, L., Zhao, L. J., Han, Y., Hao, K., & Ren, W. (2023) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2023.130350 · Cited by 11
Hietala, M., Hamada, A., Keskitalo, M., Jaskari, M., Kumpula, J., & Jarvenpää, A. (2021) · Key engineering materials · doi:10.4028/www.scientific.net/kem.883.250 · Cited by 11
He, J., Sun, J., Meng, Y., Yang, F., & Tang, H. (2021) · Journal of Materials Science · doi:10.1007/s10853-021-06415-x · Cited by 10
Tig Welding of Dissimilar Steel: A Review
Echezona, N., Akinlabi, S. A., Jen, T., Fatoba, O. S., Hassan, S., & Akinlabi, E. T. (2021) · Lecture notes in mechanical engineering · doi:10.1007/978-981-16-3641-7_1 · Cited by 10
Effect of microstructure on initial corrosion behavior of T92/HR3C dissimilar metal welded joint
Si, M., Wang, H., Wang, Q., Yang, J., & Kang, J. (2023) · Journal of Materials Science · doi:10.1007/s10853-023-09139-2 · Cited by 10
Vengaloor, R. P., & Muralidhar, R. (2023) · The International Arab Journal of Information Technology · doi:10.34028/iajit/21/1/9 · Cited by 10
Liao, H., Peng, C., You, L., Hu, J., Cheng, L., Zhang, Q., Wu, X., Xu, L., & Wang, Z. (2026) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2026.119196 · Cited by 9
Cold metal transfer welding of 316L/430 dissimilar stainless-steel welds
Tembhurkar, C. K., Ambade, S. P., Kataria, R., Verma, J., & Moon, A. P. (2023) · Anti-Corrosion Methods and Materials · doi:10.1108/acmm-03-2023-2774 · Cited by 9
On the bending of MS1-P20 hybrid steels additively manufactured using laser powder bed fusion
Shakerin, S., Sanjari, M., Pirgazi, H., Amirkhiz, B. S., & Mohammadi, M. (2022) · Materialia · doi:10.1016/j.mtla.2022.101501 · Cited by 8
Mayai, A., Prasomthong, S., & Pookamnerd, Y. (2025) · EUREKA Physics and Engineering · doi:10.21303/2461-4262.2025.003606 · Cited by 7
Deep learning-based methods for detecting surface defects in steel plates
Patil, S., Miglani, A., Kankar, P. K., & Roy, D. (2022) · Elsevier eBooks · doi:10.1016/b978-0-323-90789-7.00001-4 · Cited by 8
Kaba, L., Kellai, A., Dehimi, S., Kahla, S., Boutaghou, Z., & Bendris, T. (2024) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-024-09973-8 · Cited by 7
Kumar, A., Maji, K., & Samanta, A. (2024) · Journal of Adhesion Science and Technology · doi:10.1080/01694243.2024.2419886 · Cited by 7
Wang, H., Zhang, C., Zhou, Z., Zhang, Y., Wang, K., Wang, W., Peng, H., Lu, Y., Li, X., Liu, Y., et al. (2022) · Materials Research Express · doi:10.1088/2053-1591/ac80a4 · Cited by 7
Self-citationWang, H., Zhang, F., & Yi, R. (2025) · Sensors · doi:10.3390/s25226890 · Cited by 6
Pu, Y., Chen, Z., Zhang, B., Dong, C., Tang, D., Zeng, H., & Chen, S. (2025) · Nano Materials Science · doi:10.1016/j.nanoms.2025.11.016 · Cited by 6
Liu, H., Zhao, J. L., Han, K., Xu, F., Liu, H., & Li, F. (2024) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-024-14676-4 · Cited by 6
Simion, G., Rosca, J. C. M., Voiculescu, I., & Scutelnicu, E. (2024) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2024.11.082 · Cited by 6
Hafizi, M., Kasiri-Asgarani, M., Naalchian, M., Bakhsheshi‐Rad, H. R., & Berto, F. (2022) · Micromachines · doi:10.3390/mi13111801 · Cited by 4
Effect of Temperature on Corrosion Behavior of Laser-Remelted CrFeCoNi Coating
Wang, C., Yu, Y., Shao, M., & Zhang, H. (2022) · Metals · doi:10.3390/met12060970 · Cited by 4
Self-citationYurchenko, Y. V., Сіора, О. В., Соколовський, М. В., Harder, D. A., & Bernatskyi, A. V. (2025) · ВІСНИК СХІДНОУКРАЇНСЬКОГО НАЦІОНАЛЬНОГО УНІВЕРСИТЕТУ імені Володимира Даля · doi:10.33216/1998-7927-2025-287-1-12-20 · Cited by 3
Abbasi, R., Dehghan, S., & Loh-Mousavi, M. (2021) · Welding International · doi:10.1080/09507116.2021.1993108 · Cited by 3
Electrochemical Corrosion Behavior of CrFeCoNi and CrMnFeCoNi Coatings in Salt Solution
Wang, C., Yu, Y., He, P., Zhang, J., Ma, X., Zhang, H., Li, H., & Shao, M. (2022) · Metals · doi:10.3390/met12101752 · Cited by 3
Self-citationEffect of electrode composition over performance of dissimilar stainless-steel welds
Bakhla, M., Shukla, S., & Kumar, B. (2023) · Materials Today Proceedings · doi:10.1016/j.matpr.2023.08.164 · Cited by 3
Corrosion behavior of X80 pipeline steel in a simulated soil solution at different temperatures
Ren, G., Shi, X., Xue, Y., Zhao, Y., Liu, M., Tian, C., & Luo, S. (2026) · International Journal of Electrochemical Science · doi:10.1016/j.ijoes.2026.101358 · Cited by 2
Self-citationNagarajan, A., & Balakrishnan, M. (2023) · Materials Research Express · doi:10.1088/2053-1591/acf9de · Cited by 2
Microwave joining of SS-430 with a nano SS-316L powder
Sahota, D. S., Bansal, A., & Kumar, V. (2023) · Welding International · doi:10.1080/09507116.2023.2276709 · Cited by 2
Keskitalo, M., Hamada, A., Hietala, M., Jaskari, M., & Jarvenpää, A. (2021) · Key engineering materials · doi:10.4028/www.scientific.net/kem.883.258 · Cited by 1
Wu, Y., Liu, X., He, G., Zhou, Y., Zhou, Z., Liu, Y., Liao, Y., Wang, Z., Li, R., & Meng, Q. (2024) · The Physics of Metals and Metallography · doi:10.1134/s0031918x23602263 · Cited by 1
Balasubramani, S., Jhaa, G., Karthikeyan, R., Vincent, S., Kumar, J., Banerjee, R., Lee, M. J., & Park, E. S. (2026) · Applied Surface Science · doi:10.1016/j.apsusc.2026.166443 · Cited by 1
Microstructural and Mechanical Characteristics of Welded CoCrNi‐Based Medium Entropy Alloys
Madewu, F., Malatji, N., Shongwe, M. B., & Kanyane, L. R. (2026) · Journal of Engineering · doi:10.1155/je/1640530 · Cited by 1
Rezende, I. T., Santos, E. S., Labiapari, W. D. S., Corrêa, E. C. S., & Dumont, M. R. (2023) · Global Journal of Engineering and Technology Advances · doi:10.30574/gjeta.2023.16.2.0136 · Cited by 1
Steel Defect Detection Based on Attention Mechanism
Li, W., Yao, X., Yang, W., & Li, Y. (2023) · IEEE International Conference on Electronic Measurement & Instruments · doi:10.1109/icemi59194.2023.10269960 · Cited by 1
Bonding Strength of 12Cr-0.4C/Low Carbon Steel (LCS) Weld Joint After Solid Solution Heat Treatment
Zhu, W., Wang, Y., Zhou, J., Mao, C., Li, Y., & Gao, S. (2024) · JOM · doi:10.1007/s11837-024-06506-5 · Cited by 1
Aras, S., & Ertan, R. (2024) · Materiali in tehnologije · doi:10.17222/mit.2023.1054 · Cited by 1
Kathiresan, G., Prabakaran, M. P., Govindarasan, D., & Madeshwaren, V. (2024) · ITEGAM- Journal of Engineering and Technology for Industrial Applications (ITEGAM-JETIA) · doi:10.5935/jetia.v10i47.1045 · Cited by 1
Çuğ, H., & DAĞLAR, F. (2020) · Düzce Üniversitesi Bilim ve Teknoloji Dergisi · doi:10.29130/dubited.632999
MANUAL ARGON-ARC WELDING OPTIMIZATION OF DIFFERENT AUSTENITE STEELS 12KH18N10T AND AISI 316
Akbolatov, Y. Z., & Коровиков, А. Г. (2022) · NNC RK Bulletin · doi:10.52676/1729-7885-2021-4-22-29
"Analysis of Welding Parameters on TIG with 316 Stainless Steel Alloy"
Amin, S. A., & Rana, A. S. (2022) · International Journal of Innovative Research in Computer Science & Technology · doi:10.55524/ijircst.2022.10.4.21
Yürük, A. (2023) · Eskişehir Osmangazi Üniversitesi mühendislik ve mimarlık fakültesi dergisi :/Osmangazi Üniversitesi Mühendislik-Mimarlık Fakültesi dergisi · doi:10.31796/ogummf.1255850
Welding behavior of dissimilar joints of stainless steel: A metadata study
Pandey, P. K., Rathi, R., & Verma, J. (2023) · AIP conference proceedings · doi:10.1063/5.0162810
MIG Welded Dissimilar AISI 430/304L Butt Joint: Microstructure and Joint PerformancePreprint
SERİNDAĞ, H. T., & Çam, G. (2024) · Research Square · doi:10.21203/rs.3.rs-3774033/v1
Sil, A., Tiwari, Y., Mandal, S., Mukherjee, M., Samanta, A., & Porwal, R. K. (2024) · Advances in Materials and Processing Technologies · doi:10.1080/2374068x.2024.2373581
Corrosion properties of low-carbon steel welded joint in synthetic sea water environment
Bučko, M., Jovanović, M., Perić, S., Lazić, D., Marinković, J., & Radovanović, R. (2024) · International Scientific Conference on Defensive Technologies (OTEX) · doi:10.5937/oteh24109b
Fahem, A. H., Elmukashfi, E., & Dong, H. (2026) · steel research international · doi:10.1002/srin.202501144
Zhang, Z., Jian, Z., Xue, W., Han, K., Liu, H., Li, F., Jiao, Y., & Yuan, Z. (2026) · Research Square · doi:10.21203/rs.3.rs-9483910/v1
Abedi, M. J., Anjabin, N., Paydar, M. H., & Mazaheri, Y. (2026) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2026.07.311
Roy, R., Westraadt, J. E., & Wharry, J. P. (2026) · Research Square · doi:10.21203/rs.3.rs-10491066/v1
Jayaramaiah, C., & Nayaka, Y. A. (2026) · Surfaces and Interfaces · doi:10.1016/j.surfin.2026.110587
Yang, Y., Zhang, Y., Li, Z., Su, J., Muhammad, I. K., & Luo, Z. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.7493382
Self-citationJayaramaiah, C., & Yanjerappa, A. N. (2026) · New Journal of Chemistry · doi:10.1039/d6nj03141b
Zhu, G., Wu, Z.-Y., Xu, G.-L., Hong-ya, Y., Wang, M., Du, X.-Y., Xu-kai, R., & Chai, Y. (2026) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2026.10.179
Ribeiro, G. M. (2026) · Portuguese National Funding Agency for Science, Research and Technology (RCAAP Project by FCT)
Sharma, A., Wattal, R., & Niranjan, M. S. (2026) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-026-15425-2
Metadata
- Authors
- Wang, C., Yu, Y., Yu, J., Zhang, Y., Zhao, Y., & Yuan, Q.
- Affiliations
- Tianjin University (CN)
- Tsinghua University (CN)
- Corresponding author
- Yu, Yang
- Venue
- Journal of Manufacturing Processes
- Publisher
- Elsevier BV
- Published
- 2020-02
- Volume
- 50
- Pages
- 183-191
- ISSN
- 1526-6125 (ISSN-L)
- OpenAlex
- W2998466051
- Cited by
- 93
- References
- 43
- Citations by year
- 2026: 13 · 2025: 6 · 2024: 21 · 2023: 17 · 2022: 16 · 2021: 15 · 2020: 5
- FWCI
- 5.06
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- www.elsevier.com/tdm/userlicense/1.0/ (tdm)
- www.elsevier.com/legal/tdmrep-license (tdm)
- Locations
- Journal of Manufacturing Processes (publishedVersion)
- Funders
- National Youth Foundation of China
- Science and Technology Major Project of Guangxi
- National Natural Science Foundation of China
- China Postdoctoral Science Foundation
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Welding Techniques and Residual Stresses
- Physical Sciences › Engineering › Mechanical Engineering › Advanced Welding Techniques Analysis
- Physical Sciences › Materials Science › Metals and Alloys › Hydrogen embrittlement and corrosion behaviors in metals
- Keywords
- dissimilar metal welding, 304 stainless steel, AISI 430 stainless steel, weld microstructure, phase transformation, martensite, ferrite, austenite, corrosion resistance, phase boundaries, chromium content, high-temperature phase transitions
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.