The DOI matches its Crossref record; 41 of the 43 references it cites were found in a registry or an index.
Microstructure evolution and corrosion behavior of dissimilar 304/430 stainless steel welded joints
Abstract
Abstract Microstructure and corrosion behavior of dissimilar welds between austenitic stainless steel AISI 304 and ferritic stainless steel AISI 430 were investigated. The phase evolution within each weld was analyzed using thermodynamics calculation and electron back-scattered diffraction (EBSD). Results indicated that the welded joints were mainly composed of martensite and ferrite phases. Thermodynamic calculations show that, during the high temperature phase transformation process, the high-temperature ferrite transforms into austenite to form a mixed state. This austenite further transforms into martensite during the following high rate cooling process. It was also found that increasing the melted-in AISI 304 portion in dissimilar welds led to an increase in the austenite portion at high temperature. This resulted in more portions of martensite being present in the weld at the room temperature. Potentiodynamic polarization curves showed that the corrosion resistance of welded joint decreased with increasing fusion ration of AISI 304, and then increased with further increase in fusion ratio. The initial decrease of corrosion resistance could be attributed to the increased martensite contents and fractions of phase boundaries, and the subsequent increase might contribute to increased Cr contents and decreased fractions of phase boundaries.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“There are some shortcomings in manual testing, such as low confidence and high labor intensity.”
From A New Steel Defect Detection Algorithm Based on Deep Learning (2021) · cites this paper as [3]
Citations
Cites
Calcagnotto, M., Ponge, D., Demir, E., & Raabe, D. (2010) · Materials Science and Engineering: A · doi:10.1016/j.msea.2010.01.004 · Cited by 2,319
Cui, Z., Wang, L., Ni, H., Hao, W., Man, C., Chen, S., Wang, X., Liu, Z., & Li, X. (2017) · Corrosion Science · doi:10.1016/j.corsci.2017.01.016 · Cited by 430
Microstructure and corrosion properties of CrMnFeCoNi high entropy alloy coating
Ye, Q., Feng, K., Li, Z., Lu, F., Li, R., Huang, J., & Wu, Y. (2017) · Applied Surface Science · doi:10.1016/j.apsusc.2016.11.176 · Cited by 408
Cui, Z., Chen, S., Dou, Y., Han, S., Wang, L., Man, C., Wang, X., Chen, S., Cheng, Y. F., & Li, X. (2019) · Corrosion Science · doi:10.1016/j.corsci.2019.02.002 · Cited by 397
Kocijan, A., Merl, D. K., & Jenko, M. (2010) · Corrosion Science · doi:10.1016/j.corsci.2010.11.010 · Cited by 285
EIS study of potentiostatically formed passive film on 304 stainless steel
Mohammadi, F., Nickchi, T., Attar, M. M., & Alfantazi, A. M. (2011) · Electrochimica Acta · doi:10.1016/j.electacta.2011.07.072 · Cited by 284
Dissimilar metal friction welding of austenitic–ferritic stainless steels
Satyanarayana, V. V., Reddy, G. M., & Mohandas, T. (2005) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2004.05.017 · Cited by 254
Kundu, A., & Field, D. P. (2016) · Materials Science and Engineering A · doi:10.1016/j.msea.2016.05.022 · Cited by 232
Hidalgo, J., Findley, K. O., & Santofimia, M. J. (2017) · Materials Science and Engineering A · doi:10.1016/j.msea.2017.03.017 · Cited by 232
Microstructural features of dissimilar welds between 316LN austenitic stainless steel and alloy 800
Sireesha, M., Shankar, V, Albert, S. K., & Sundaresan, S. (2000) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(00)00969-2 · Cited by 223
Ha, H., Jang, M., Lee, T., & Moon, J. (2014) · Corrosion Science · doi:10.1016/j.corsci.2014.08.021 · Cited by 192
Application of EBSD to analysis of microstructures in commercial steels
Ryde, L. (2006) · Materials Science and Technology · doi:10.1179/174328406x130948 · Cited by 192
Wang, S., Ma, Q.-H., & Li, Y. (2010) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2010.07.012 · Cited by 185
Khorrami, M. S., Mostafaei, M. A., Pouraliakbar, H., & Kokabi, A. H. (2014) · Materials Science and Engineering A · doi:10.1016/j.msea.2014.04.065 · Cited by 184
Ge, H.-H., Zhou, G., & Wu, W. (2003) · Applied Surface Science · doi:10.1016/s0169-4332(03)00355-6 · Cited by 166
Heat transfer and fluid flow in additive manufacturing
Raghavan, A., Wei, H., Palmer, T. A., & DebRoy, T. (2013) · Journal of Laser Applications · doi:10.2351/1.4817788 · Cited by 159
Man, C., Dong, C., Cui, Z., Xiao, K., Yu, Q., & Li, X. (2017) · Applied Surface Science · doi:10.1016/j.apsusc.2017.08.151 · Cited by 146
Hajiannia, I., SHAMANIAN, M., & Kasiri, M. (2013) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2013.03.029 · Cited by 140
Ebrahimi, N., Momeni, M., Kosari, A., Zakeri, M., & Moayed, M. H. (2012) · Corrosion Science · doi:10.1016/j.corsci.2012.02.026 · Cited by 128
Chen, T., John, H., Xu, J. J., Lu, Q., Hawk, J. A., & Liu, X. (2013) · Corrosion Science · doi:10.1016/j.corsci.2013.08.007 · Cited by 127
Ramkumar, T., Selvakumar, M., Narayanasamy, P., Begam, A. A., Mathavan, P., & Raj, A. (2017) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2017.09.028 · Cited by 121
Evidence of back diffusion reducing cracking during solidification
Liu, J., Duarte, H. P., & Kou, S. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.09.037 · Cited by 118
Wu, W., Hu, S., & Shen, J. (2014) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2014.09.064 · Cited by 95
Mechanical and Structural Properties of Similar and Dissimilar Steel Joints
Çelik, A., & Alsaran, A. (1999) · Materials Characterization · doi:10.1016/s1044-5803(99)00045-5 · Cited by 92
Laser beam welding of dissimilar stainless steels in a fillet joint configuration
Khan, M. M. A., Romoli, L., Fiaschi, M., Dini, G., & Sarri, F. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2011.11.011 · Cited by 90
Boissy, C., Ter-Ovanessian, B., Mary, N., & Normand, B. (2015) · Electrochimica Acta · doi:10.1016/j.electacta.2015.05.179 · Cited by 85
Marangoni convection in weld pools with a free surface
Tsai, M.-J., & Kou, S. (1989) · International Journal for Numerical Methods in Fluids · doi:10.1002/fld.1650091206 · Cited by 82
Lai, R., Cai, Y., Wu, Y., Li, F., & Hua, X. (2016) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2016.01.016 · Cited by 74
High-toughness joining of aluminum alloy 5754 and DQSK steel using hybrid clinching–welding process
Zhang, Y., Wang, C., Shan, H., Li, Y., & Luo, Z. (2018) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2018.04.021 · Cited by 70
Self-citationJia, Q., Guo, W., Wan, Z., Peng, Y. Y., Zou, G., Tian, Z., & Zhou, Y. (2018) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2018.04.020 · Cited by 56
Archie, F. M. F., Li, X., & Zaefferer, S. (2017) · Materials Science and Engineering A · doi:10.1016/j.msea.2017.06.094 · Cited by 53
Hsieh, C.-C., Lin, D., Chen, M.-C., & Wu, W. (2007) · Materials Science and Engineering A · doi:10.1016/j.msea.2007.05.037 · Cited by 48
Local electrochemical properties of fusion boundary region in SA508-309L/308L overlay welded joint
Lai, Z., Bi, P. Y., Wen, L., Xue, Y., & Jin, Y. J. (2019) · Corrosion Science · doi:10.1016/j.corsci.2019.04.021 · Cited by 40
•Microstructure Evolution and Solidification Cracking in Austenitic Stainless Steel Welds
American Welding Society (2018) · Welding Journal · doi:10.29391/2018.97.026 · Cited by 38
Kang, K., Kawahito, Y., Gao, M. X., & Zeng, X. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.03.049 · Cited by 37
Pourabbas, M., Abdollah-Zadeh, A., Sarvari, M., Pouranvari, M., & Miresmaeili, R. (2018) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2018.12.002 · Cited by 36
Austenite reversion in low-carbon martensitic stainless steels – a CALPHAD-assisted review
Nießen, F. (2018) · Materials Science and Technology · doi:10.1080/02670836.2018.1449179 · Cited by 35
Pasupathi, S., & Manikandan, M. (2018) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2018.06.037 · Cited by 24
Zhang, X., Zhang, Y., Wu, Y., Ao, S., & Luo, Z. (2019) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2018.12.025 · Cited by 15
Self-citationLaser weldability of 21Cr-6Ni-9Mn stainless steel: Part I - Impurity effects and solidifcation mode
Tate, S., Javernick, D. A., Lienert, T. J., & Liu, S. (2016) · OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) · Cited by 2
Laser weldability of 21Cr-6Ni-9Mn stainless steel: Part II - Weldability diagrams
Tate, S., Javernick, D. A., Lienert, T. J., & Liu, S. (2016) · OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) · Cited by 2
Research works printed but not linked: 2
- Saunders, 1998, 1
- Houldcroft, 1954, Dilution and uniformity in aluminum alloy weld beads, Br Weld J, 1, 468
Cited by
A New Steel Defect Detection Algorithm Based on Deep Learning
Zhao, W., Chen, F., Huang, H., Li, D., & Cheng, W. (2021) · Computational Intelligence and Neuroscience · doi:10.1155/2021/5592878 · Cited by 259
Wang, C., Yu, J., Yu, Y., Zhao, Y., Zhang, Y., & Han, X. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.05.093 · Cited by 104
Self-citationSelected corrosion of X80 pipeline steel welded joints induced by Desulfovibrio desulfuricans
Wang, Q. L., Zhou, X., Ma, Q., Wu, T., Liu, M., Zhang, M., Li, Z., & Yin, F. (2022) · Corrosion Science · doi:10.1016/j.corsci.2022.110313 · Cited by 69
Laser Dissimilar Welding of AISI 430F and AISI 304 Stainless Steels
Pańcikiewicz, K., Świerczyńska, A., Hućko, P., & Tumidajewicz, M. (2020) · Materials · doi:10.3390/ma13204540 · Cited by 65
Research on Steel Surface Defect Detection Based on YOLOv5 with Attention Mechanism
Shi, J., Yang, J., & Zhang, Y. (2022) · Electronics · doi:10.3390/electronics11223735 · Cited by 58
Self-citation
Metadata
- Authors
- Wang, C., Yu, Y., Yu, J., Zhang, Y., Zhao, Y., & Yuan, Q.
- Affiliations
- Tianjin University (CN)
- Tsinghua University (CN)
- Corresponding author
- Yu, Yang
- Venue
- Journal of Manufacturing Processes
- Publisher
- Elsevier BV
- Published
- 2020-02
- Volume
- 50
- Pages
- 183-191
- ISSN
- 1526-6125 (ISSN-L)
- OpenAlex
- W2998466051
- Cited by
- 93
- References
- 43
- Citations by year
- 2026: 13 · 2025: 6 · 2024: 21 · 2023: 17 · 2022: 16 · 2021: 15 · 2020: 5
- FWCI
- 5.06
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- www.elsevier.com/tdm/userlicense/1.0/ (tdm)
- www.elsevier.com/legal/tdmrep-license (tdm)
- Locations
- Journal of Manufacturing Processes (publishedVersion)
- Funders
- National Youth Foundation of China
- Science and Technology Major Project of Guangxi
- National Natural Science Foundation of China
- China Postdoctoral Science Foundation
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Welding Techniques and Residual Stresses
- Physical Sciences › Engineering › Mechanical Engineering › Advanced Welding Techniques Analysis
- Physical Sciences › Materials Science › Metals and Alloys › Hydrogen embrittlement and corrosion behaviors in metals
- Keywords
- dissimilar metal welding, 304 stainless steel, AISI 430 stainless steel, weld microstructure, phase transformation, martensite, ferrite, austenite, corrosion resistance, phase boundaries, chromium content, high-temperature phase transitions
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.