Student or educator? Sign up with your school email and get 6 months of Pro free.
Cited by 391

The DOI matches its Crossref record; 12 of the 12 references it cites were found in a registry or an index.

Dry machining of Inconel 718, workpiece surface integrity

Open access
Devillez, A., Le Coz, G., Dominiak, S., Dudzinski, D. · 2011 · Journal of Materials Processing Technology

Abstract

In the machining of Inconel 718, nickel based heat resistant superalloy and classified difficult-to-cut material, the consumption of cooling lubricant is very important. To reduce the costs of production and to make the processes environmentally safe, the goal is to move toward dry cutting by eliminating cutting fluids. This goal can be achieved by using coated carbide tool and by increasing cutting speed. The present paper firstly reviews the main works on surface integrity and especially residual stresses when machining Inconel 718 superalloy. It focuses then on the effect of dry machining on surface integrity. Wet and dry turning tests were performed at various cutting speeds, with semi-finishing conditions (0.5 mm depth of cut and 0.1 mm/rev feed rate) and using a coated carbide tool. For each cutting test, cutting force was measured, machined surface was observed, and residual stress profiles were determined. An optimal cutting speed of 60 m/min was determined, and additional measurements and observations were performed. Microhardness increment and the microstructure alteration beneath the machined surface were analysed. It is demonstrated that dry machining with a coated carbide tool leads to potentially acceptable surface quality with residual stresses and microhardness values in the machining affected zone of the same order than those obtained in wet conditions when using the optimised cutting speed value; in addition, no severe microstructure alteration was depicted.

Overview

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1016/j.jmatprotec.2011.04.011

Cites

12 of 12 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 12 references

Cited by

See all 391

Metadata

Authors
Devillez, A., Le Coz, G., Dominiak, S., & Dudzinski, D.
Venue
Journal of Materials Processing Technology
Publisher
Elsevier BV
Published
2011-10
Volume
211
Issue
10
Pages
1590-1598
ISSN
0924-0136 (ISSN-L)
OpenAlex
W1965308830
Cited by
391
References
12
FWCI
33.58
Type
journal article
Language
en
Open access
green

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Dry machining of Inconel 718, workpiece surface integrity. https://app.cochat.ai/papers/10.1016/j.jmatprotec.2011.04.011
The paper
Devillez, A., Le Coz, G., Dominiak, S., & Dudzinski, D. (2011). Dry machining of Inconel 718, workpiece surface integrity. Journal of Materials Processing Technology. https://doi.org/10.1016/j.jmatprotec.2011.04.011

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.