The DOI matches its Crossref record; 39 of the 39 references it cites were found in a registry or an index.
Vertical continuous compound casting of copper aluminum bilayer rods
Open accessAbstract
Abstract A vertical continuous compound casting technology for the production of rotationally symmetric bilayer rods consisting of brass CuZn37 and aluminum AA7075 was developed. The interface of the metallurgically bonded semi-finished products was composed of four intermetallic layers and an anomalous eutectic area of Al2Cu (θ-AlCu), Al solid solution (α-Al), and other intermetallic precipitates. The intermetallic layers were CuZn (β-CuZn), a suggested two-phase region of Al3Cu5Zn2 (τ-AlCuZn) and Cu5Zn8 (γ-CuZn), Al4Cu3Zn (τ′-AlCuZn), and AlCu (η2-AlCu). The correlation between the process parameters casting speed, cladding temperature, and tool tempering and the interface formation was studied. The experimental investigations were accompanied by a numerical FEM analysis. The casting speed and the cladding temperature were found to be key factors, that influence the formation of a cohesion between the joining partners.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The thermal conditions in the casting process and, sequentially, the formation of intermetallic phases can be modified via several process parameters depending on the respective process.For example, these can be the pouring temperature [2,3], preheating temperature of the insert [4] or mold temperature/cladding temperature [5].”
From Investigation of the Microstructure and Properties of Aluminum–Copper Compounds Fabricated by the High-Pressure Die Casting Process (2022) · cites this paper as [5]
In the citing paper
“However, cavities are reported only as a characteristic of a poor bond formation in the interfacial layer, which can be reduced by increasing the heat impact [2,3,5,16].”
From Investigation of the Microstructure and Properties of Aluminum–Copper Compounds Fabricated by the High-Pressure Die Casting Process (2022) · cites this paper as [5]
Citations
Cites
New equations for heat and mass transfer in turbulent pipe and channel flow
Gnielinski, V. (1976) · Medical Entomology and Zoology · Cited by 4,037
Moody, M. P., Stephenson, L. T., Ceguerra, A. V., & Ringer, S. P. (2008) · Microscopy Research and Technique · doi:10.1002/jemt.20582 · Cited by 235
Interface formation in aluminium–aluminium compound casting
Papis, K., Hallstedt, B., Löffler, J. F., et al. (2008) · Acta Materialia · doi:10.1016/j.actamat.2008.02.042 · Cited by 123
Structure Data of Elements and Intermetallic Phases
Hellwege, K.-H., & Hellwege, A. M. (1971) · Springer eBooks · doi:10.1007/b19971 · Cited by 111
Improved steel/aluminum bonding in bimetallic castings by a compound casting process
Jiang, W., Fan, Z., & Li, C. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.06.032 · Cited by 107
Jiang, Z., Fan, Z., Jiang, W., Li, G., Wu, Y., Guan, F., & Jiang, H. (2018) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2018.06.013 · Cited by 83
Jiang, W., Li, G., Fan, Z., Wang, L., & Liu, F. (2016) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-016-3395-9 · Cited by 71
Investigation on interface of Al/Cu couples in compound casting
Zare, G. R., Divandari, M., & Arabi, H. (2013) · Materials Science and Technology · doi:10.1179/1743284712y.0000000096 · Cited by 68
Study of Al/Cu rich phases formed in A356 alloy by inserting Cu wire in pattern in LFC process
Divandari, M., & Golpayegani, A. R. V. (2009) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2009.01.008 · Cited by 43
Pintore, M., Starykov, O., Mittler, T., Volk, W., & Tonn, B. (2017) · International Journal of Metalcasting · doi:10.1007/s40962-017-0140-0 · Cited by 40
Self-citation
Research works printed but not linked: 1
- Ißleib, 1995, Compound casting of iron-carbon alloys – fundamental metallurgical reactions at the interface – part II [Verbundgießen von Eisen-Kohlenstoff-Legierungen – grundlegende metallurgische Reaktionen an der Grenzfläche – Teil II], Gießerei-Praxis, 23/24, 442
Cited by
Nolte, N., Lukasczyk, T., & Mayer, B. (2022) · Metals · doi:10.3390/met12081314 · Cited by 5
“poor bond formation in the interfacial layer, which can be reduced by increasing the heat impact [2,3,5,16].”
BackgroundRingel, A., Demirezen, A. Z., Hoyer, J., Bailly, D., Kammerloher, S., Volk, W., & Lian, J. (2026) · Materials Science Forum · doi:10.4028/p-ifcfc6
“The resulting composite rod is extracted from the mold using rolling drawers that employ a go-stop withdrawal technique to avoid tearing the rod due to friction [24].”
Self-citation
Metadata
- Authors
- Greß, T., Glück Nardi, V., Schmid, S., Hoyer, J., Rizaiev, Y., Boll, T., Seils, S., Tonn, B., & Volk, W.
- Affiliations
- Technical University of Munich (DE)
- Karlsruhe Institute of Technology (DE)
- Clausthal University of Technology (DE)
- Corresponding author
- Greß, Thomas
- Venue
- Journal of Materials Processing Technology
- Publisher
- Elsevier BV
- Published
- 2021-02
- Volume
- 288
- Pages
- 116854
- ISSN
- 0924-0136 (ISSN-L)
- OpenAlex
- W3046437208
- Cited by
- 22
- References
- 39
- Citations by year
- 2026: 4 · 2025: 2 · 2024: 3 · 2023: 6 · 2022: 6 · 2021: 1
- FWCI
- 1.56
- Type
- journal article
- Language
- en
- Open access
- Licence
- cc-by-nc-nd
- www.elsevier.com/tdm/userlicense/1.0/ (tdm)
- www.elsevier.com/legal/tdmrep-license (tdm)
- Locations
- Journal of Materials Processing Technology (publishedVersion)
- Repository KITopen (Karlsruhe Institute of Technology) (acceptedVersion, cc-by-nc-nd)
- mediaTUM – the media and publications repository of the Technical University Munich (Technical University Munich) (submittedVersion, cc-by-nc-nd)
- KITopen
- Funders
- Deutsche Forschungsgemeinschaft (VO-1487/41-1, numberVO-1487/41-1)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced Welding Techniques Analysis
- Physical Sciences › Materials Science › Metals and Alloys › Aluminum Alloy Microstructure Properties
- Physical Sciences › Materials Science › Metals and Alloys › Metallurgy and Material Science
- Keywords
- intermetallic compound layer, interface formation, cladding temperature, casting speed, finite element analysis
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Vertical continuous compound casting of copper aluminum bilayer rods. https://app.cochat.ai/papers/10.1016/j.jmatprotec.2020.116854
- The paper
- Greß, T., Glück Nardi, V., Schmid, S., Hoyer, J., Rizaiev, Y., Boll, T., Seils, S., Tonn, B., & Volk, W. (2021). Vertical continuous compound casting of copper aluminum bilayer rods. Journal of Materials Processing Technology. https://doi.org/10.1016/j.jmatprotec.2020.116854
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.
