The DOI matches its Crossref record; 17 of the 17 references it cites were found in a registry or an index.
Comparative study on 3D printing of polyamide 12 by selective laser sintering and multi jet fusion
Abstract
Abstract Selective laser sintering (SLS) and Multi Jet Fusion (MJF) are two of the most developed powder bed fusion additive manufacturing techniques for the manufacture of polymeric components. In this work, a systematic benchmark and comparison of polyamide 12 (PA12) parts printed by SLS and MJF was conducted on the physicochemical characterization of raw powder materials (EOS PA2200 and HP 3D HR PA12) and their printed specimens, as well as the mechanical performance and printing characteristics of printed objects. Both designated-supply PA12 powders for each technique possessed almost identical thermal features, phase constitutions, functional groups, and chemical states. The mechanical strength of the MJF-printed specimens was slightly stronger than that of SLS-printed counterparts due to the synergistic effect of an area fusion mode and carbon black additive in the MJF process. The SLS-printed specimens had a better surface finish on the top surface, but the MJF-printed specimens showed much smoother front and side surfaces. Scaled-down merlions were printed by both processes for the printing accuracy assessment. The results show that the SLS-printed merlion presented higher profile deviations than those of the MJF-printed counterpart, especially in areas with sharp contours. These fundamental experimental results can provide a comprehensive understanding of SLS and MJF processes and serve as a valuable guideline for their industrial applications.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Additive manufacturing: scientific and technological challenges, market uptake and opportunities
Tofail, S. A. M., Koumoulos, E. P., Bandyopadhyay, A., Bose, S., O’Donoghue, L., & Charitidis, C. (2018) · Materials Today · doi:10.1016/j.mattod.2017.07.001 · Cited by 2,136
Laser sintering of polyamides and other polymers
Goodridge, R. D., Tuck, C. J., & Hague, R. J. M. (2012) · Progress in Materials Science · doi:10.1016/j.pmatsci.2011.04.001 · Cited by 835
Recent Progress on Polymer Materials for Additive Manufacturing
Tan, L. J., Zhu, W., & Zhou, K. (2020) · Advanced Functional Materials · doi:10.1002/adfm.202003062 · Cited by 740
Self-citationDependence of mechanical properties of polyamide components on build parameters in the SLS process
Caulfield, B., McHugh, P. E., & Lohfeld, S. (2007) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2006.09.007 · Cited by 598
Effects of processing on microstructure and properties of SLS Nylon 12
Zarringhalam, H., Hopkinson, N., Kamperman, N. F., & de Vlieger, J. J. (2006) · Materials Science and Engineering: A · doi:10.1016/j.msea.2006.07.084 · Cited by 295
Characterization of polyamide powders for determination of laser sintering processability
Verbelen, L., Dadbakhsh, S., Van den Eynde, M., Kruth, J.-P., Goderis, B., & Van Puyvelde, P. (2016) · European Polymer Journal · doi:10.1016/j.eurpolymj.2015.12.014 · Cited by 208
Effect of PA12 powder reuse on coalescence behaviour and microstructure of SLS parts
Dadbakhsh, S., Verbelen, L., Verkinderen, O., Strobbe, D., Van Puyvelde, P., & Kruth, J.-P. (2017) · European Polymer Journal · doi:10.1016/j.eurpolymj.2017.05.014 · Cited by 204
Van Hooreweder, B., Moens, D., Boonen, R., Kruth, J.-P., & Sas, P. (2013) · Polymer Testing · doi:10.1016/j.polymertesting.2013.04.014 · Cited by 190
O’Connor, H. J., Dickson, A. N., & Dowling, D. P. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2018.05.035 · Cited by 185
Cited by
Additive manufacturing of polymeric composites from material processing to structural design
Yuan, S., Li, S., Zhu, J., & Tang, Y. (2021) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2021.108903 · Cited by 267
Study on Geometry, Dimensional Accuracy and Structure of Parts Produced by Multi Jet Fusion
Adach, M., Sokołowski, P., Piwowarczyk, T., & Nowak, K. (2021) · Materials · doi:10.3390/ma14164510 · Cited by 27
Ponticelli, G. S., Tagliaferri, F., Venettacci, S., Horn, M., Giannini, O., & Guarino, S. (2021) · Applied Sciences · doi:10.3390/app11167375 · Cited by 23
Metadata
- Authors
- Cai, C., Tey, W. S., Chen, J., Zhu, W., Liu, X., Liu, T., Zhao, L., & Zhou, K.
- Venue
- Journal of Materials Processing Technology
- Publisher
- Elsevier BV
- Published
- 2021-02
- Volume
- 288
- Pages
- 116882
- ISSN
- 0924-0136 (ISSN-L)
- OpenAlex
- W3051157269
- Cited by
- 288
- References
- 17
- FWCI
- 15.24
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Comparative study on 3D printing of polyamide 12 by selective laser sintering and multi jet fusion. https://app.cochat.ai/papers/10.1016/j.jmatprotec.2020.116882
- The paper
- Cai, C., Tey, W. S., Chen, J., Zhu, W., Liu, X., Liu, T., Zhao, L., & Zhou, K. (2021). Comparative study on 3D printing of polyamide 12 by selective laser sintering and multi jet fusion. Journal of Materials Processing Technology. https://doi.org/10.1016/j.jmatprotec.2020.116882
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.