The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
3D-printed PLA/HA composite structures as synthetic trabecular bone: A feasibility study using fused deposition modeling
Abstract
Additive manufacturing has significant advantages, in the biomedical field, allowing for customized medical products where complex architectures can be achieved directly. While additive manufacturing can be used to fabricate synthetic bone models, this approach is limited by the printing resolution, at the level of the trabecular bone architecture. Therefore, the aim of this study was to evaluate the possibilities of using fused deposition modeling (FDM) to this end. To better mimic real bone, both in terms of mechanical properties and biodegradability, a composite of degradable polymer, poly(lactic acid) (PLA), and hydroxyapatite (HA) was used as the filament. Three PLA/HA composite formulations with 5-10-15 wt% HA were evaluated, and scaled up human trabecular bone models were printed using these materials. Morphometric and mechanical properties of the printed models were evaluated by micro-computed tomography, compression and screw pull out tests. It was shown that the trabecular architecture could be reproduced with FDM and PLA by applying a scaling factor of 2-4. The incorporation of HA particles reduced the printing accuracy, with respect to morphology, but showed potential for enhancement of the mechanical properties. The scaled-up models displayed comparable, or slightly enhanced, strength compared to the commonly used polymeric foam synthetic bone models (i.e. Sawbones). Reproducing the trabecular morphology by 3D printed PLA/HA composites appears to be a promising strategy for synthetic bone models, when high printed resolution can be achieved.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Zhang, H., Mao, X., Du, Z., Jiang, W., Han, X., Zhao, D., Han, D., & Li, Q. (2016) · Science and Technology of Advanced Materials · doi:10.1080/14686996.2016.1145532 · Cited by 208
Lin, P.-L., Fang, H.-W., Tseng, T., & Lee, W.-H. (2007) · Materials Letters · doi:10.1016/j.matlet.2006.10.064 · Cited by 87
Cited by
Additive manufacturing of structural materials
Liu, G., Zhang, X., Chen, X., He, Y., Cheng, L., Huo, M., Yin, J., Hao, F., Chen, S., Wang, P., et al. (2021) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2020.100596 · Cited by 707
Fused deposition modeling: process, materials, parameters, properties, and applications
Rajan, K., Samykano, M., Kadirgama, K., Harun, W. S. W., & Rahman, M. M. (2022) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-08860-7 · Cited by 426
Fabrication of Biomedical Scaffolds Using Biodegradable Polymers.
Kirillova, A., Yeazel, T. R., Asheghali, D., Petersen, S. R., Dort, S., Gall, K., & Becker, M. L. (2021) · Chemical Reviews · doi:10.1021/acs.chemrev.0c01200 · Cited by 368
Åkerlund, E., Diez-Escudero, A., Grzeszczak, A., & Persson, C. (2022) · Polymers · doi:10.3390/polym14163305 · Cited by 80
Self-citation
Metadata
- Authors
- Wu, D., Spanou, A., Diez-Escudero, A., & Persson, C.
- Venue
- Journal of the Mechanical Behavior of Biomedical Materials
- Publisher
- Elsevier BV
- Published
- 2020-03
- Volume
- 103
- Pages
- 103608
- ISSN
- 1751-6161 (ISSN-L)
- OpenAlex
- W2970801947
- Cited by
- 161
- References
- 2
- FWCI
- 5.80
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: 3D-printed PLA/HA composite structures as synthetic trabecular bone: A feasibility study using fused deposition modeling. https://app.cochat.ai/papers/10.1016/j.jmbbm.2019.103608
- The paper
- Wu, D., Spanou, A., Diez-Escudero, A., & Persson, C. (2020). 3D-printed PLA/HA composite structures as synthetic trabecular bone: A feasibility study using fused deposition modeling. Journal of the Mechanical Behavior of Biomedical Materials. https://doi.org/10.1016/j.jmbbm.2019.103608
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.