The DOI matches its Crossref record; 60 of the 60 references it cites were found in a registry or an index.
A review: drilling performance and hole quality of aluminium alloys for aerospace applications
Open accessAbstract
Despite the growth of composites and other lightweight materials, aluminium alloys remain an attractive choice of the aerospace industry due to their mature manufacturing processes, good resistance to fatigue crack growth and superior damage tolerance. In the aerospace industry, the drilling process is the most challenging among all the other machining process as millions of holes are required for producing riveted and bolted joints in the assembly operation of the aircraft's structures. The major challenges which arise from the drilling of these alloys are characterized by the poor hole quality which might initiate cracks within the airframe structure and reduces their reliability. This results in the rejection of parts at the assembly stage which directly impacts the manufacturing cost. Hence, appropriate selection of tool geometry, tool material and coatings, optimal cutting speed and feed rate, as well as drilling machines, is required to meet the requirement of machined parts. This motivates both academia and industries to further research on the application of drilling operations in the aircraft industry. This review aims to document details on drilling forces, drilling parameters, drill tool geometry, drill materials and coatings, chips formation, analysis of tool wear and hole metrics such as the hole size and circularity error, surface roughness, and burrs formation during the drilling of different aluminium alloys used in the aerospace industry. The focus will be mainly on Al2024 and Al7075 alloys since they are most commonly used and reported in the open literature.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Recent developments in advanced aircraft aluminium alloys
Dursun, T., & Soutis, C. (2014) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2013.12.002 · Cited by 2,807
Idris, M. H., Jafari, H., Harandi, S. E., Mirshahi, M., & Koleyni, S. J. (2012) · Advanced materials research · Cited by 2,357
Williams, J. C., & Starke, E. A. (2003) · Acta Materialia · doi:10.1016/j.actamat.2003.08.023 · Cited by 2,342
Fundamentals of modern manufacturing
Groover, M. P. (1996) · Cited by 1,841
Metal Cutting Theory and Practice
Stephenson, D. A., & Agapiou, J. (2016) · CRC Press eBooks · doi:10.1201/9781315373119 · Cited by 969
A review of mechanical drilling for composite laminates
Liu, D., Tang, Y., & Cong, W. L. (2012) · Composite Structures · doi:10.1016/j.compstruct.2011.11.024 · Cited by 781
Karataş, M. A., & Gökkaya, H. (2018) · Defence Technology · doi:10.1016/j.dt.2018.02.001 · Cited by 755
Klocke, F., & Eisenblätter, G. (1997) · CIRP Annals · doi:10.1016/s0007-8506(07)60877-4 · Cited by 742
Dry machining: Machining of the future
Sreejith, P. S., & Ngoi, B. K. A. (2000) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(00)00445-3 · Cited by 684
Machining of Polymer Composites
Sheikh-Ahmad, J. Y. (2009) · Springer eBooks · doi:10.1007/978-0-387-68619-6 · Cited by 644
Fundamentals of Metal Machining and Machine Tools
Knight, W. A., & Boothroyd, G. (2019) · CRC Press eBooks · doi:10.1201/9780429114243 · Cited by 527
Introduction to Aerospace Materials
Mouritz, A. (2012) · American Institute of Aeronautics and Astronautics eBooks · doi:10.2514/4.869198 · Cited by 511
Geier, N., Davim, J. P., & Szalay, T. (2019) · Composites Part A Applied Science and Manufacturing · doi:10.1016/j.compositesa.2019.105552 · Cited by 413
Recent advances in drilling of carbon fiber–reinforced polymers for aerospace applications: a review
Aamir, M., Tolouei-Rad, M., Giasin, K., & Nosrati, A. (2019) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-019-04348-z · Cited by 329
Self-citationMachining of aluminum alloys: a review
Santos, M. C., Machado, A. R., Sales, W. F., Barrozo, M. A. S., & Ezugwu, E. O. (2016) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-016-8431-9 · Cited by 326
Study of drilling of composite material and aluminium stack
Zitoune, R., Krishnaraj, V., & Collombet, F. (2010) · Composite Structures · doi:10.1016/j.compstruct.2009.10.010 · Cited by 323
Experimental analysis and optimisation of tool wear in dry machining of aluminium alloys
Nouari, M., List, G., Girot, F., & Coupard, D. (2003) · Wear · doi:10.1016/s0043-1648(03)00105-4 · Cited by 284
Minimal lubrication machining of aluminium alloys
Kelly, J. F., & Cotterell, M. G. (2002) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(01)01126-8 · Cited by 242
Recent advances in drilling hybrid FRP/Ti composite: A state-of-the-art review
Xu, J., Mkaddem, A., & El Mansori, M. (2016) · Composite Structures · doi:10.1016/j.compstruct.2015.09.028 · Cited by 242
The effect of vibratory drilling on hole quality in polymeric composites
Arul, S., Vijayaraghavan, L., Malhotra, S. K., & Krishnamurthy, R. (2005) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2005.05.023 · Cited by 227
Mohan, N. S., Ramachandra, A., & Kulkarni, S. M. (2005) · Composite Structures · doi:10.1016/j.compstruct.2005.09.039 · Cited by 201
Kurt, M., Bagci, E., & Kaynak, Y. (2009) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-007-1368-2 · Cited by 198 · cited 3×
“↑ Speed [53,70–73,75] [58,96] [72,73,78,96] [24,52,97] [53,70,71,74,75] – ↑ Feed [24,53,58,70–73,75] [52] [72,73,96,97] [52] [53,70,71,75] [53] ↑ Point angle [75] [52,58,72] [78] [52,58,72] [75] – ↑ Helix angle [52] [58] – ↑ Drill diameter [73] – [73]”
BackgroundWear behaviour of cemented carbide tools in dry machining of aluminium alloy
List, G., Nouari, M., Gehin, D., et al. (2005) · Wear · doi:10.1016/j.wear.2005.02.056 · Cited by 187
Environmentally Friendly Machining
Dixit, U. S., Sarma, D. K., & Davim, J. P. (2012) · SpringerBriefs in Applied Sciences and Technology · doi:10.1007/978-1-4614-2308-9 · Cited by 165
Kılıçkap, E. (2010) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-009-2469-x · Cited by 153
Effect of machining parameters and coating on wear mechanisms in dry drilling of aluminium alloys
Nouari, M., List, G., Girot, F. A., et al. (2005) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2005.01.026 · Cited by 150
MECHANICAL DRILLING PROCESSES FOR TITANIUM ALLOYS: A LITERATURE REVIEW
Zhang, P. F., Churi, N. J., Pei, Z. J., & Treadwell, C. (2008) · Machining Science and Technology · doi:10.1080/10910340802519379 · Cited by 141
Drilling on fiber reinforced polymer/nanopolymer composite laminates: a review
Panchagnula, K. K., & Kuppan, P. (2017) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2017.06.003 · Cited by 136
Giasin, K., & Ayvar-Soberanis, S. (2016) · Composite Structures · doi:10.1016/j.compstruct.2016.10.015 · Cited by 134
Self-citationHelical milling: An enabling technology for hard machining precision holes in AISI D2 tool steel
Iyer, R. M., Koshy, P., & Ng, E. (2006) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2006.04.006 · Cited by 127
Giasin, K., Hodzic, A., Phadnis, V. A., & Ayvar-Soberanis, S. (2016) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-016-8563-y · Cited by 118
Self-citationEvaluating Hole Quality in Drilling of Al 6061 Alloys
Uddin, M., Basak, A., Pramanik, A., Singh, S., Krolczyk, G. M., & Prakash, C. (2018) · Materials · doi:10.3390/ma11122443 · Cited by 109
Analysis of burr formation in drilling with a new-concept drill
Ko, S.-L., & Lee, J.-K. (2001) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(01)00717-8 · Cited by 109
Evaluation of drilled hole quality in Al 2024 alloy
Kurt, M., Kaynak, Y., & Bagci, E. (2008) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-007-1049-1 · Cited by 102
Introduction to aerospace materials
(2012) · Elsevier eBooks · doi:10.1533/9780857095152.1 · Cited by 97
Kalidas, S., DeVor, R. E., & Kapoor, S. G. (2001) · Surface and Coatings Technology · doi:10.1016/s0257-8972(01)01349-4 · Cited by 92
Drilling of Polymer-Matrix Composites
Krishnaraj, V., Zitoune, R., & Davim, J. P. (2013) · SpringerBriefs in applied sciences and technology · doi:10.1007/978-3-642-38345-8 · Cited by 92
Aamir, M., Tu, S., Tolouei-Rad, M., Giasin, K., & Vafadar, A. (2020) · Materials · doi:10.3390/ma13030680 · Cited by 86 · cited 2×
“[26] Aamir M, Tu S, Tolouei-Rad M, Giasin K, Vafadar A.”
BackgroundSelf-citationEvaluation of novel tool geometries in dry drilling aluminium 2024-T351/titanium Ti6Al4V stack
Zhu, Z., Guo, K., Sun, J., Li, J., Liu, Y., Zheng, Y., & Chen, L. (2018) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2018.04.044 · Cited by 84
Tool wear and hole quality investigation in dry helical milling of Ti-6Al-4V alloy
Li, H., He, G., Qin, X., Wang, G., Lu, C., & Gui, L. (2014) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-013-5570-0 · Cited by 84
Coelho, R. T., Yamada, S., Aspinwall, D. K., et al. (1995) · International Journal of Machine Tools and Manufacture · doi:10.1016/0890-6955(95)93044-7 · Cited by 84
Fundamentals of Machining Processes: Conventional and Nonconventional Processes
El-Hofy, H. (2006) · Cited by 83
Sun, D., Lemoine, P., Keys, D., Doyle, P., Malinov, S., Zhao, Q., Qin, X., & Jin, Y. (2018) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-016-9850-3 · Cited by 80
Evolution of 3D chip morphology and phase transformation in dry drilling Ti6Al4V alloys
Zhu, Z., Guo, K., Sun, J., Li, J., Liu, Y., Chen, L., & Zheng, Y. (2018) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2018.07.001 · Cited by 78
Machining Technology: Machine Tools and Operations
Youssef, H. A., & El-Hofy, H. (2008) · Medical Entomology and Zoology · Cited by 76
Machining technology: machine tools and operations
(2008) · Choice Reviews Online · doi:10.5860/choice.46-0911 · Cited by 75
Finite Element Analysis of Drilling of Titanium Alloy
Isbilir, O., & Ghassemieh, E. (2011) · Procedia Engineering · doi:10.1016/j.proeng.2011.04.312 · Cited by 74
Machinability of Al2024, Al6061, and Al5083 alloys using multi-hole simultaneous drilling approach
Aamir, M., Tolouei‐Rad, M., Giasin, K., & Vafadar, A. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.07.078 · Cited by 71
Self-citationFatigue performance of production-quality aircraft fastener holes
Ralph, W. C., Johnson, W. S., Makeev, A., & Newman, J. C. (2006) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2006.10.016 · Cited by 48
Effect of detail design on fatigue performance of fastener hole
Li, X., Xu, H., Zhai, H., & Yue, Z. F. (2009) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2009.08.016 · Cited by 43
Álvarez-Alcón, M., de Lacalle, L. N. L., & Fernández-Zacarías, F. (2020) · Materials · doi:10.3390/ma13122796 · Cited by 32
Neseli, S. (2014) · Advances in Mechanical Engineering · doi:10.1155/2014/925382 · Cited by 30
Optimization of facing process by indigenously developed force dynamometer
Hanif, M. I., Aamir, M., Ahmed, N., Maqsood, S., Muhammad, R., Akhtar, R., & Hussain, I. (2019) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-018-2829-5 · Cited by 29
Self-citationProcessing Techniques and Tribological Behavior of Composite Materials
Tyagi, R., & Davim, J. P. (2015) · Advances in chemical and materials engineering book series · doi:10.4018/978-1-4666-7530-8 · Cited by 26
Aamir, M., Tu, S., Giasin, K., & Tolouei‐Rad, M. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.02.026 · Cited by 26
Self-citationBurr height monitoring while drilling CFRP/titanium/aluminium stacks
Rimpault, X., Châtelain, J.-F., Klemberg-Sapieha, J. E., & Balazinski, M. (2017) · Mechanics & Industry · doi:10.1051/meca/2015073 · Cited by 22
Machining Fibre Metal Laminates and Al2024-T3aluminium alloy
Giasin, K. (2017) · White Rose eTheses Online (University of Leeds, The University of Sheffield, University of York) · Cited by 21
Self-citationEffect of drilling process on fatigue life of open holes
Gu, W., Xu, H., Liu, J., & Yue, Z. (2009) · Tsinghua Science & Technology · doi:10.1016/s1007-0214(10)70031-6 · Cited by 16
Intelligent Analysis of Utilization of Special Purpose Machines for Drilling Operations
Tolouei‐Rad, M. (2012) · Intelligent Systems · doi:10.5772/36896 · Cited by 14
Self-citationC.Thirupathaiah, A. S. R. G. V. K. (2013) · International Journal of Innovative Research in Science Engineering and Technology · Cited by 6
Metadata
- Authors
- Aamir, M., Giasin, K., Tolouei-Rad, M., & Vafadar, A.
- Venue
- Journal of Materials Research and Technology
- Publisher
- Elsevier BV
- Published
- 2020-11
- Volume
- 9
- Issue
- 6
- Pages
- 12484-12500
- ISSN
- 2214-0697 (ISSN-L)
- 2238-7854
- OpenAlex
- W3088802907
- Cited by
- 286
- References
- 60
- FWCI
- 16.28
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.