The DOI matches its Crossref record; 66 of the 66 references it cites were found in a registry or an index.
A critical review on additive manufacturing of Ti-6Al-4V alloy: microstructure and mechanical properties
Open accessAbstract
The most popular additive manufacturing (AM) technologies to produce titanium alloy parts are electron beam melting (EBM), selective laser melting (SLM) and directed energy deposition (DED). This investigation explores mainly these three techniques and compares these three methods comprehensively in terms of microstructure, tensile properties, porosity, surface roughness and residual stress based on the information available in the literature. It was found that the microstructure is affected by the highest temperature generated and the cooling rate which can be tailored by the input variables of the AM processes. The parts produced from EBM have strength comparable to that of conventionally fabricated counterparts. SLM and DED yield superior strength, which can be up to 25% higher than traditionally manufactured products. Due to the presence of larger tensile residual stress, surface roughness and porosity, AM fabricated parts have lower fatigue life compared to those of from traditional methods. EBM parts have slightly lower fracture toughness (i.e., lower fatigue life) than conventionally produced parts while SLM and DED have significantly lower fracture toughness. Annealing, hot isostatic pressing, stress relief and additional machining processes improve the characteristics of parts produced from AM. Ti–6Al–4V alloy parts fabricated via AM may have limited applications despite the high demands in aerospace or biomedical engineering. Since rapid product development using 3D printers leads to significant cost reductions more recently, it is expected that more opportunities may soon be available for the AM of titanium alloys with newer AM processes such as cold spray additive manufacturing (CSAM) and additive friction stir deposition (AFSD).
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
Gibson, I., Rosen, D., & Stucker, B. (2015) · doi:10.1007/978-1-4939-2113-3 · Cited by 3,299
Additive manufacturing of Ti6Al4V alloy: A review
Liu, S., & Shin, Y. C. (2019) · Materials & Design · doi:10.1016/j.matdes.2018.107552 · Cited by 2,472
Donachie, M. J. (1988) · Cited by 1,662
Carroll, B. E., Palmer, T. A., & Beese, A. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.12.054 · Cited by 1,507
Leuders, S., Thöne, M., Riemer, A., Niendorf, T., Tröster, T., Richard, H. A., & Maier, H. J. (2013) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2012.11.011 · Cited by 1,475
Vilaro, T., Colin, C., & Bartout, J. D. (2011) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-011-0731-y · Cited by 1,283
Phase transformations during cooling in α+β titanium alloys
Ahmed, T., & Rack, H. J. (1998) · Materials Science and Engineering A · doi:10.1016/s0921-5093(97)00802-2 · Cited by 1,224
Gong, H., Rafi, K., Gu, H., Starr, T., & Stucker, B. (2014) · Additive Manufacturing · doi:10.1016/j.addma.2014.08.002 · Cited by 1,038
Mechanical behavior of additive manufactured, powder-bed laser-fused materials
Mower, T. M., & Long, M. J. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.10.068 · Cited by 1,001
Cited by
Chowdhury, S., Yadaiah, N., Prakash, C., Ramakrishna, S., Dixit, S., Gupta, L. R., & Buddhi, D. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.07.121 · Cited by 784
Self-citationMukherjee, T., Elmer, J. W., Wei, H. L., Lienert, T. J., Zhang, W., Kou, S., & DebRoy, T. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2023.101153 · Cited by 267
Metadata
- Authors
- Nguyen, H. D., Pramanik, A., Basak, A. K., Dong, Y., Prakash, C., Debnath, S., Shankar, S., Jawahir, I. S., Dixit, S., & Buddhi, D.
- Venue
- Journal of Materials Research and Technology
- Publisher
- Elsevier BV
- Published
- 2022-05
- Volume
- 18
- Pages
- 4641-4661
- ISSN
- 2214-0697 (ISSN-L)
- 2238-7854
- OpenAlex
- W4226237687
- Cited by
- 634
- References
- 66
- FWCI
- 45.50
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: A critical review on additive manufacturing of Ti-6Al-4V alloy: microstructure and mechanical properties. https://app.cochat.ai/papers/10.1016/j.jmrt.2022.04.055
- The paper
- Nguyen, H. D., Pramanik, A., Basak, A. K., Dong, Y., Prakash, C., Debnath, S., Shankar, S., Jawahir, I. S., Dixit, S., & Buddhi, D. (2022). A critical review on additive manufacturing of Ti-6Al-4V alloy: microstructure and mechanical properties. Journal of Materials Research and Technology. https://doi.org/10.1016/j.jmrt.2022.04.055
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.