The DOI matches its Crossref record; 66 of the 66 references it cites were found in a registry or an index.
A critical review on additive manufacturing of Ti-6Al-4V alloy: microstructure and mechanical properties
Open accessAbstract
The most popular additive manufacturing (AM) technologies to produce titanium alloy parts are electron beam melting (EBM), selective laser melting (SLM) and directed energy deposition (DED). This investigation explores mainly these three techniques and compares these three methods comprehensively in terms of microstructure, tensile properties, porosity, surface roughness and residual stress based on the information available in the literature. It was found that the microstructure is affected by the highest temperature generated and the cooling rate which can be tailored by the input variables of the AM processes. The parts produced from EBM have strength comparable to that of conventionally fabricated counterparts. SLM and DED yield superior strength, which can be up to 25% higher than traditionally manufactured products. Due to the presence of larger tensile residual stress, surface roughness and porosity, AM fabricated parts have lower fatigue life compared to those of from traditional methods. EBM parts have slightly lower fracture toughness (i.e., lower fatigue life) than conventionally produced parts while SLM and DED have significantly lower fracture toughness. Annealing, hot isostatic pressing, stress relief and additional machining processes improve the characteristics of parts produced from AM. Ti–6Al–4V alloy parts fabricated via AM may have limited applications despite the high demands in aerospace or biomedical engineering. Since rapid product development using 3D printers leads to significant cost reductions more recently, it is expected that more opportunities may soon be available for the AM of titanium alloys with newer AM processes such as cold spray additive manufacturing (CSAM) and additive friction stir deposition (AFSD).
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
Gibson, I., Rosen, D., & Stucker, B. (2015) · doi:10.1007/978-1-4939-2113-3 · Cited by 3,299
Additive manufacturing of Ti6Al4V alloy: A review
Liu, S., & Shin, Y. C. (2019) · Materials & Design · doi:10.1016/j.matdes.2018.107552 · Cited by 2,472
Donachie, M. J. (1988) · Cited by 1,662
Carroll, B. E., Palmer, T. A., & Beese, A. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.12.054 · Cited by 1,507
Leuders, S., Thöne, M., Riemer, A., Niendorf, T., Tröster, T., Richard, H. A., & Maier, H. J. (2013) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2012.11.011 · Cited by 1,475
Vilaro, T., Colin, C., & Bartout, J. D. (2011) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-011-0731-y · Cited by 1,283
Phase transformations during cooling in α+β titanium alloys
Ahmed, T., & Rack, H. J. (1998) · Materials Science and Engineering A · doi:10.1016/s0921-5093(97)00802-2 · Cited by 1,224
Gong, H., Rafi, K., Gu, H., Starr, T., & Stucker, B. (2014) · Additive Manufacturing · doi:10.1016/j.addma.2014.08.002 · Cited by 1,038
Mechanical behavior of additive manufactured, powder-bed laser-fused materials
Mower, T. M., & Long, M. J. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.10.068 · Cited by 1,001
Rafi, H. K., Karthik, N. V., Gong, H., Starr, T. L., & Stucker, B. E. (2013) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-013-0658-0 · Cited by 987
Defect formation mechanisms in selective laser melting: a review
Zhang, B., Li, Y., & Bai, Q. (2017) · Chinese Journal of Mechanical Engineering · doi:10.1007/s10033-017-0121-5 · Cited by 924
Fatigue performance evaluation of selective laser melted Ti–6Al–4V
Edwards, P., & Ramulu, M. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2014.01.041 · Cited by 874
Al-Bermani, S. S., Blackmore, M., Zhang, W., & Todd, I. (2010) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-010-0397-x · Cited by 860
Wang, Z., Palmer, T. A., & Beese, A. M. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.03.019 · Cited by 830
Parry, L., Ashcroft, I. A., & Wildman, R. D. (2016) · Additive Manufacturing · doi:10.1016/j.addma.2016.05.014 · Cited by 739
Improvement of fatigue resistance and ductility of TiAl6V4 processed by selective laser melting
Kasperovich, G., & Hausmann, J. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.01.025 · Cited by 735
Zhao, X., Li, S., Zhang, M., Liu, Y., Sercombe, T. B., Wang, S., Hao, Y., Yang, R., & Murr, L. E. (2016) · Materials & Design · doi:10.1016/j.matdes.2015.12.135 · Cited by 673
Economics of additive manufacturing for end-usable metal parts
Atzeni, E., & Salmi, A. (2012) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3878-1 · Cited by 630
Baufeld, B., Brandl, E., & der Biest, O. V. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2011.01.018 · Cited by 537
Yadroitsev, I., Krakhmalev, P., & Yadroitsava, I. (2014) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2013.08.183 · Cited by 515
Effects of Defects in Laser Additive Manufactured Ti-6Al-4V on Fatigue Properties
Wycisk, E., Solbach, A., Siddique, S., Herzog, D., Walther, F., & Emmelmann, C. (2014) · Physics Procedia · doi:10.1016/j.phpro.2014.08.120 · Cited by 509
Characterization of Metal Powders Used for Additive Manufacturing
Slotwinski, J. A., Garboczi, E. J., Stutzman, P. E., Ferraris, C. F., Watson, S. S., & Peltz, M. A. (2014) · Journal of Research of the National Institute of Standards and Technology · doi:10.6028/jres.119.018 · Cited by 506
The Influence of Porosity on Fatigue Crack Initiation in Additively Manufactured Titanium Components
Tammas-Williams, S., Withers, P. J., Todd, I., & Prangnell, P. B. (2017) · Scientific Reports · doi:10.1038/s41598-017-06504-5 · Cited by 494
Additive Manufacturing of Titanium Alloys by Electron Beam Melting: A Review
Zhang, L., Liu, Y., Li, S., & Hao, Y. (2018) · Advanced Engineering Materials · doi:10.1002/adem.201700842 · Cited by 486
Electron Beam Additive Manufacturing of Titanium Components: Properties and Performance
Edwards, P., O'Conner, A., & Ramulu, M. (2013) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4025773 · Cited by 450
Microstructures of laser-deposited Ti–6Al–4V
Wu, X., Liang, J., Mei, J., Mitchell, C., Goodwin, P. S., & Voice, W. (2004) · Materials & Design · doi:10.1016/j.matdes.2003.09.009 · Cited by 436
Tan, J. H., Wong, W. L. E., & Dalgarno, K. W. (2017) · Additive Manufacturing · doi:10.1016/j.addma.2017.10.011 · Cited by 407
de Formanoir, C., Michotte, S., Rigo, O., Germain, L., & Godet, S. (2015) · Materials Science and Engineering A · doi:10.1016/j.msea.2015.11.052 · Cited by 404
On the Texture Formation of Selective Laser Melted Ti-6Al-4V
Simonelli, M., Tse, Y. Y., & Tuck, C. J. (2014) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-014-2218-0 · Cited by 391
Problems and solutions in machining of titanium alloys
Pramanik, A. (2014) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-013-5326-x · Cited by 382
Self-citationA review of powder additive manufacturing processes for metallic biomaterials
Harun, W. S. W., Kamariah, M. S. I. N., Muhamad, N., Ghani, S. A. C., Ahmad, F., & Mohamed, Z. (2018) · Powder Technology · doi:10.1016/j.powtec.2017.12.058 · Cited by 379
Fatigue behavior and failure mechanisms of direct laser deposited Ti–6Al–4V
Sterling, A. J., Torries, B., Shamsaei, N., Thompson, S. M., & Seely, D. W. (2015) · Materials Science and Engineering A · doi:10.1016/j.msea.2015.12.026 · Cited by 372
Hrabe, N., Gnäupel-Herold, T., & Quinn, T. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.04.022 · Cited by 355
Hrabe, N. W., & Quinn, T. P. (2013) · Materials Science and Engineering A · doi:10.1016/j.msea.2013.02.065 · Cited by 349
Galarraga, H., Lados, D. A., Dehoff, R., Kirka, M. M., & Nandwana, P. (2016) · Additive manufacturing · doi:10.1016/j.addma.2016.02.003 · Cited by 334
Chan, K. S., Koike, M., Mason, R. L., & Okabe, T. (2013) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-012-1470-4 · Cited by 320
Fabrication of large Ti–6Al–4V structures by direct laser deposition
Qiu, C., Ravi, G. A., Dance, C., Ranson, A., Dilworth, S., & Attallah, M. M. (2015) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2014.12.234 · Cited by 304
Laser and Electron Beam Additive Manufacturing Methods of Fabricating Titanium Bone Implants
Wysocki, B., Maj, P., Sitek, R., Buhagiar, J., Kurzydłowski, K., & Święszkowski, W. (2017) · Applied Sciences · doi:10.3390/app7070657 · Cited by 300
Seifi, M., Salem, A. A., Satko, D. P., Shaffer, J., & Lewandowski, J. J. (2016) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.06.001 · Cited by 291
Facchini, L., Magalini, E., Robotti, P., & Molinari, A. (2009) · Rapid Prototyping Journal · doi:10.1108/13552540910960262 · Cited by 290
Koike, M., Greer, P., Owen, K., Guo, L., Murr, L. E., Gaytan, S. M., Martinez, E., & Okabe, T. H. (2011) · Materials · doi:10.3390/ma4101776 · Cited by 270
Biomedical titanium alloys and their additive manufacturing
Hao, Y., Li, S., & Yang, R. (2016) · Rare Metals · doi:10.1007/s12598-016-0793-5 · Cited by 267
Predicting tensile properties of Ti-6Al-4V produced via directed energy deposition
Hayes, B. J., Martin, B. W., Welk, B. A., Kuhr, S. J., Ales, T. K., Brice, D. A., Ghamarian, I., Baker, A. H., Haden, C. V., Harlow, D. G., et al. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.05.025 · Cited by 257
Chastand, V., Quaegebeur, P., Maia, W., & Charkaluk, E. (2018) · Materials Characterization · doi:10.1016/j.matchar.2018.03.028 · Cited by 234
Porosity formation and gas bubble retention in laser metal deposition
Ng, G. K. L., Jarfors, A. E. W., Bi, G., & Zheng, H. Y. (2009) · Applied Physics A · doi:10.1007/s00339-009-5266-3 · Cited by 230
Influence of tempering temperature and time on the α′-Ti-6Al-4V martensite
Gil, F. X., Rius, D. R., & Planell, J. A. (1996) · Journal of Alloys and Compounds · doi:10.1016/0925-8388(95)02057-8 · Cited by 230
Chern, A. H., Nandwana, P., Yuan, T., Kirka, M. M., Dehoff, R. R., Liaw, P. K., & Duty, C. E. (2019) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2018.09.022 · Cited by 216
Titanium in Medical and Dental Applications
(2018) · Elsevier eBooks · doi:10.1016/c2016-0-03591-x · Cited by 206
Liu, Q. C., Elambasseril, J., Sun, S. J., Leary, M., Brandt, M., & Sharp, P. K. (2014) · Advanced Materials Research · doi:10.4028/www.scientific.net/amr.891-892.1519 · Cited by 201
Material Properties of Ti6Al4V Parts Produced by Laser Metal Deposition
Yu, J., Rombouts, M., Maes, G., & Motmans, F. (2012) · Physics Procedia · doi:10.1016/j.phpro.2012.10.056 · Cited by 193
Keist, J. S., & Palmer, T. A. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.05.045 · Cited by 173
Balla, V. K., DeVasConCellos, P. D., Xue, W., Bose, S., & Bandyopadhyay, A. (2009) · Acta Biomaterialia · doi:10.1016/j.actbio.2009.01.011 · Cited by 170
Guo, S., Lu, Y., Wu, S., Liu, L., He, M., Zhao, C., Gan, Y., Lin, J., Luo, J., Xu, X., et al. (2017) · Materials Science and Engineering: C · doi:10.1016/j.msec.2016.11.126 · Cited by 163
Gu, D., Hagedorn, Y., Meiners, W., Wissenbach, K., & Poprawe, R. (2010) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2010.11.051 · Cited by 144
Analysis of effect of alloying elements on martensite start temperature of steels
Capdevila, C., Caballero, F. G., & de Andrés, C. G. (2003) · Materials Science and Technology · doi:10.1179/026708303225001902 · Cited by 101
Han, C., Wang, Q., Song, B., Li, W., Wei, Q., Wen, S., Liu, J., & Shi, Y. (2017) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2017.02.021 · Cited by 100
Cooke, A., & Slotwinski, J. A. (2012) · doi:10.6028/nist.ir.7873 · Cited by 90
Xu, X., Lu, Y., Li, S., Guo, S., He, M., Luo, K., & Lin, J. (2018) · Materials Science and Engineering C · doi:10.1016/j.msec.2018.04.046 · Cited by 90
Effect of Melt Scan Rate on Microstructure and Macrostructure for Electron Beam Melting of Ti-6Al-4V
Puebla, K., Murr, L. E., Gaytan, S. M., Martinez, E., Medina, F. R., & Wicker, R. B. (2012) · Materials Sciences and Applications · doi:10.4236/msa.2012.35038 · Cited by 85
Wei, C., Liu, L., Cao, H., Zhong, X., Xu, X., Gu, Y., Cheng, D., Huang, Y., Li, Z., Guo, W., et al. (2022) · Additive manufacturing · doi:10.1016/j.addma.2021.102588 · Cited by 67
Dislocation Strengthening without Ductility Trade-off in Metastable Austenitic Steels
Liu, J., Jin, Y., Fang, X., Chen, C., Feng, Q., Liu, X., Chen, Y. Z., Suo, T., Zhao, F., Huang, T., et al. (2016) · Scientific Reports · doi:10.1038/srep35345 · Cited by 57
Gu, D., Chen, H., & Meng, G. (2011) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-011-0876-8 · Cited by 51
Brogini, S., Sartori, M., Giavaresi, G., Cremascoli, P., Alemani, F., Bellini, D., Martini, L., Maglio, M., Pagani, S., & Fini, M. (2020) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2020.104262 · Cited by 45
Fathi-Hafshejani, P., Johnson, H. A., Ahmadi, Z., Roach, M. D., Shamsaei, N., & Mahjouri‐Samani, M. (2020) · ACS Omega · doi:10.1021/acsomega.0c01671 · Cited by 34
Razavi, N., Bordonaro, G., Ferro, P., Torgersen, J., & Berto, F. (2018) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406218813384 · Cited by 30
Cited by
Chowdhury, S., Yadaiah, N., Prakash, C., Ramakrishna, S., Dixit, S., Gupta, L. R., & Buddhi, D. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.07.121 · Cited by 784
Self-citationMukherjee, T., Elmer, J. W., Wei, H. L., Lienert, T. J., Zhang, W., Kou, S., & DebRoy, T. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2023.101153 · Cited by 267
Metadata
- Authors
- Nguyen, H. D., Pramanik, A., Basak, A. K., Dong, Y., Prakash, C., Debnath, S., Shankar, S., Jawahir, I. S., Dixit, S., & Buddhi, D.
- Venue
- Journal of Materials Research and Technology
- Publisher
- Elsevier BV
- Published
- 2022-05
- Volume
- 18
- Pages
- 4641-4661
- ISSN
- 2214-0697 (ISSN-L)
- 2238-7854
- OpenAlex
- W4226237687
- Cited by
- 634
- References
- 66
- FWCI
- 45.50
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.