The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Dual extrusion 3D printing of mashed potatoes/strawberry juice gel
Abstract
Abstract Currently most of food printers apply one printhead to extrude a single or a mixture of multiple materials. Such a printhead cannot control the materials distribution in a drop-on-demand way, while a multi-extruder printer enables the fabrication of highly attractive multi-material constructs with higher geometric complexity. In this study, the effects of extruder offset and retraction on the printing behavior were firstly optimized, followed by the preliminary tests of two methods of dual extrusion 3D printing. Method A is to create a multi-part model and assign each of them to one extruder. Method B is to create a single part model and assign different roles to each extruder. Some constructs with different inside shape were created using Method A. Product hardness and gumminess increased linearly with mashed potatoes (MP) percentage but showed no correlation with inside shape. Porous samples with special texture were printed using Method B by varying infill levels. Total printing time, firmness, hardness and gumminess increased with infill levels, and a clear discrimination was observed by principle component analysis (PCA). This suggested that dual extrusion 3D printing enables the fabrication of attractive multi-material constructs and has a potential to tailor textural properties of samples through varying infill percentage.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
3D printing: Printing precision and application in food sector
Liu, Z., Zhang, M., Bhandari, B., & Wang, Y. (2017) · Trends in Food Science & Technology · doi:10.1016/j.tifs.2017.08.018 · Cited by 858
Self-citationVancauwenberghe, V., Verboven, P., Lammertyn, J., & Nicolaï, B. (2018) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2018.01.008 · Cited by 96
Cited by
Liu, Z., Bhandari, B., Prakash, S., Mantihal, S., & Zhang, M. (2019) · Food Hydrocolloids · doi:10.1016/j.foodhyd.2018.08.026 · Cited by 530
Self-citation3D food printing of fresh vegetables using food hydrocolloids for dysphagic patients
Pant, A., Lee, A. Y., Karyappa, R., Lee, C. P., An, J., Hashimoto, M., Tan, U.-X., Wong, G., Chua, C. K., & Zhang, Y. (2021) · Food Hydrocolloids · doi:10.1016/j.foodhyd.2020.106546 · Cited by 371
Yu, J., Wang, X.-Y., Li, D., Wang, L.-J., & Wang, Y. (2022) · Food Hydrocolloids · doi:10.1016/j.foodhyd.2022.107824 · Cited by 285
Dick, A., Bhandari, B., & Prakash, S. (2019) · Meat Science · doi:10.1016/j.meatsci.2019.03.005 · Cited by 264
3D food printing: main components selection by considering rheological properties
Jiang, H., Zheng, L., Zou, Y., Tong, Z., Han, S., & Wang, S. (2019) · Critical Reviews in Food Science and Nutrition · doi:10.1080/10408398.2018.1514363 · Cited by 226
Metadata
- Authors
- Liu, Z., Zhang, M., & Yang, C.-H.
- Venue
- LWT
- Publisher
- Elsevier BV
- Published
- 2018-10
- Volume
- 96
- Pages
- 589-596
- ISSN
- 0023-6438 (ISSN-L)
- OpenAlex
- W2806759458
- Cited by
- 203
- References
- 2
- FWCI
- 8.01
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Dual extrusion 3D printing of mashed potatoes/strawberry juice gel. https://app.cochat.ai/papers/10.1016/j.lwt.2018.06.014
- The paper
- Liu, Z., Zhang, M., & Yang, C.-H. (2018). Dual extrusion 3D printing of mashed potatoes/strawberry juice gel. LWT. https://doi.org/10.1016/j.lwt.2018.06.014
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.