The DOI matches its Crossref record; 42 of the 42 references it cites were found in a registry or an index.
Linking rheology and printability of a multicomponent gel system of carrageenan-xanthan-starch in extrusion based additive manufacturing
Abstract
3D food printing is an emerging technology with a potential to influence the food manufacturing sector. Rheological properties of food inks are critical for their successful 3D printing. However, the relationships between rheological properties and 3D printability have not been clearly defined in food systems. In this work, a gel model system composed of carrageenan-xanthan-starch was prepared for an extrusion-based 3D food printer. The 3D printing process was divided into three stages and the corresponding rheological properties of inks for each stage were determined, namely extrusion stage (yield stress, viscosity and shear-thinning behaviour), recovery stage (shear recovery and temperature recovery properties) and self-supporting stage (complex modulus G* and yield stress at room temperature). Finally, 3D printability of the model inks was systematically studied starting with printing lines/pentagram (one dimensional, 1D structure) to printing lattice scaffold (two dimensional, 2D structure) and finally printing cylinders (three dimensional, 3D structure). Results demonstrated that addition of starch and xanthan gum in k-carrageenan based inks increased inks’ gelation temperature (Tgelation), viscosity (within shear rate of 0.01–100 1/s), yield stress, G* enhanced shear-thinning (thixotropic) behaviour and reduced time-dependence of modulus (temperature recovery). Rheological responses of yield stress (cross-over point where G′ (elastic modulus) equals to G′′ (viscous modulus) in the stress sweep tests) and shear-thinning behaviour (viscosity decreased when shear rate increased) were closely related to ink's extrudability. Inks’ gelation temperature (Tgelation) and time-dependent behaviour (gelation time, tgel) significantly affected their printability and shape retention performance. The mechanical strength of the ink is important to be self-supporting, especially for 3D structures. Insights achieved from this study could provide guidance on improving 3D printability of foods that use hydrocolloids as a printing aid.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Direct Ink Writing of 3D Functional Materials
Lewis, J. A. (2006) · Advanced Functional Materials · doi:10.1002/adfm.200600434 · Cited by 1,740
Bioink properties before, during and after 3D bioprinting
Hölzl, K., Lin, S., Tytgat, L., Van Vlierberghe, S., Gu, L., & Ovsianikov, A. (2016) · Biofabrication · doi:10.1088/1758-5090/8/3/032002 · Cited by 1,070
Ouyang, L., Yao, R., Zhao, Y., & Sun, W. (2016) · Biofabrication · doi:10.1088/1758-5090/8/3/035020 · Cited by 1,045
Paxton, N., Smolan, W., Böck, T., Melchels, F., Groll, J., & Jungst, T. (2017) · Biofabrication · doi:10.1088/1758-5090/aa8dd8 · Cited by 950
3D printing: Printing precision and application in food sector
Liu, Z., Zhang, M., Bhandari, B., & Wang, Y. (2017) · Trends in Food Science & Technology · doi:10.1016/j.tifs.2017.08.018 · Cited by 858
Self-citationDirect Ink Writing of Three‐Dimensional Ceramic Structures
Lewis, J. A., Smay, J. E., Stuecker, J., & Cesarano, J. (2006) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2006.01382.x · Cited by 823
From rapid prototyping to home fabrication: How 3D printing is changing business model innovation
Rayna, T., & Striukova, L. (2016) · Technological Forecasting and Social Change · doi:10.1016/j.techfore.2015.07.023 · Cited by 816
Research on the printability of hydrogels in 3D bioprinting
He, Y., Yang, F., Zhao, H., Gao, Q., Xia, B., & Fu, J. (2016) · Scientific Reports · doi:10.1038/srep29977 · Cited by 654
Applicability of protein and fiber-rich food materials in extrusion-based 3D printing
Lille, M., Nurmela, A., Nordlund, E., Metsä-Kortelainen, S., & Sozer, N. (2018) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2017.04.034 · Cited by 615
Bio-ink properties and printability for extrusion printing living cells
Chung, J. H. Y., Naficy, S., Yue, Z., Kapsa, R., Quigley, A., Moulton, S. E., & Wallace, G. G. (2013) · Biomaterials Science · doi:10.1039/c3bm00012e · Cited by 610
Cited by
Yu, J., Wang, X.-Y., Li, D., Wang, L.-J., & Wang, Y. (2022) · Food Hydrocolloids · doi:10.1016/j.foodhyd.2022.107824 · Cited by 285
3D food printing: a categorised review of inks and their development
Voon, S. L., An, J., Wong, G., Zhang, Y., & Chua, C. K. (2019) · Virtual and Physical Prototyping · doi:10.1080/17452759.2019.1603508 · Cited by 175
3D printing to innovate biopolymer materials for demanding applications: A review
Li, N., Qiao, D., Zhao, S., Lin, Q., Zhang, B., & Xie, F. (2021) · Materials Today Chemistry · doi:10.1016/j.mtchem.2021.100459 · Cited by 142
Outrequin, T. C. R., Gamonpilas, C., Siriwatwechakul, W., & Sreearunothai, P. (2023) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2022.111371 · Cited by 113
Abedini, A., Sohrabvandi, S., Sadighara, P., Hosseini, H., Farhoodi, M., Assadpour, E., Alizadeh Sani, M., Zhang, F., Seyyedi-Mansour, S., & Jafari, S. M. (2024) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2024.103181 · Cited by 71
Metadata
- Authors
- Liu, Z., Bhandari, B., Prakash, S., Mantihal, S., & Zhang, M.
- Venue
- Food Hydrocolloids
- Publisher
- Elsevier BV
- Published
- 2019-02
- Volume
- 87
- Pages
- 413-424
- ISSN
- 0268-005X (ISSN-L)
- OpenAlex
- W2887391136
- Cited by
- 530
- References
- 42
- FWCI
- 15.37
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Linking rheology and printability of a multicomponent gel system of carrageenan-xanthan-starch in extrusion based additive manufacturing. https://app.cochat.ai/papers/10.1016/j.foodhyd.2018.08.026
- The paper
- Liu, Z., Bhandari, B., Prakash, S., Mantihal, S., & Zhang, M. (2019). Linking rheology and printability of a multicomponent gel system of carrageenan-xanthan-starch in extrusion based additive manufacturing. Food Hydrocolloids. https://doi.org/10.1016/j.foodhyd.2018.08.026
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.