The DOI matches its Crossref record.
Additive manufactured WE43 magnesium: A comparative study of the microstructure and mechanical properties with those of powder extruded and as-cast WE43
Abstract
Abstract Laser powder-bed fusion (L-PBF), an additive manufacturing (AM) method, was employed to produce WE43 magnesium cubes with minimal porosity. These samples were subjected to microstructural analysis by utilizing optical light and scanning electron microscopy techniques in addition to x-ray diffraction and compared to powder extruded and as-cast WE43 reference samples. The mechanical properties of the three materials were evaluated via tensile testing. Furthermore, the microstructure of the original powder material was investigated. The additive manufactured samples and the powder extruded (PE) samples showed an extremely fine, homogeneous microstructure with grain sizes of ~1 μm and very fine secondary phases; the crystallographic structure of these phases could not be indisputably identified via XRD except for yttrium oxides. The microstructure of the as-cast material revealed different phases. Laser scan traces can clearly be observed in the microstructure as a result of the applied exposure strategy or small clusters of orientated grains that may be correlated to differing heat impacts between the center and edge-near areas of the sample due to melt pool preservation during the direction change of the laser path. Tensile tests show a significant alteration of properties in comparison to the tested conventional as-cast material. The tensile tests of the additive manufactured and powder extruded material revealed an ultimate tensile strength of 308 and 306 MPa at 12 and 22% elongation to failure, respectively. For both materials, an upper and lower yield point phenomenon was observed which is attributed to the fine grain size. The presented investigations render the additive manufacturing (AM) process suitable to produce samples that show a homogeneous and dense microstructure, mostly independent of the build direction, with exceptional high mechanical properties and to exhibit to a great extend similar features to powder extruded samples.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Additive manufacturing of biodegradable metals: Current research status and future perspectives
Qin, Y., Wen, P., Guo, H., Xia, D., Zheng, Y., Jauer, L., Poprawe, R., Voshage, M., & Schleifenbaum, J. H. (2019) · Acta Biomaterialia · doi:10.1016/j.actbio.2019.04.046 · Cited by 303
Self-citationRecent progress and perspectives in additive manufacturing of magnesium alloys
Zeng, Z., Salehi, M., Kopp, A., Xu, S., Esmaily, M., & Birbilis, N. (2022) · Journal of Magnesium and Alloys · doi:10.1016/j.jma.2022.03.001 · Cited by 264
Design, printing, and engineering of regenerative biomaterials for personalized bone healthcare
Jia, Z., Xu, X., Zhu, D., & Zheng, Y. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2023.101072 · Cited by 176
Wang, Z., Liu, B., Yin, B., Zheng, Y., Tian, Y., & Wen, P. (2022) · Frontiers in Chemistry · doi:10.3389/fchem.2022.1066103 · Cited by 30
Metadata
- Authors
- Zumdick, N. A., Jauer, L., Kersting, L. C., Kutz, T. N., Schleifenbaum, J. H., & Zander, D.
- Venue
- Materials Characterization
- Publisher
- Elsevier BV
- Published
- 2019-01
- Volume
- 147
- Pages
- 384-397
- ISSN
- 1044-5803 (ISSN-L)
- OpenAlex
- W2900068464
- Cited by
- 215
- References
- 0
- FWCI
- 8.95
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Additive manufactured WE43 magnesium: A comparative study of the microstructure and mechanical properties with those of powder extruded and as-cast WE43. https://app.cochat.ai/papers/10.1016/j.matchar.2018.11.011
- The paper
- Zumdick, N. A., Jauer, L., Kersting, L. C., Kutz, T. N., Schleifenbaum, J. H., & Zander, D. (2019). Additive manufactured WE43 magnesium: A comparative study of the microstructure and mechanical properties with those of powder extruded and as-cast WE43. Materials Characterization. https://doi.org/10.1016/j.matchar.2018.11.011
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.