The DOI matches its Crossref record; 17 of the 17 references it cites were found in a registry or an index.
Selective laser melting of AlSi10Mg: Influence of post-processing on the microstructural and tensile properties development
Open accessAbstract
The study looks into the impact of thermal post-processing using Hot Isostatic Pressing (HIPping) and/or T6-peak aging treatment, post-process machining, as well as the build orientation on the microstructural and mechanical properties development in AlSi10Mg alloy fabricated using Selective Laser Melting (SLM). The builds contained fine columnar grains, with a fine Si-enriched cellular dendritic network, resulting in tensile strengths exceeding the castings. To elucidate the as-fabricated microstructure and strength, thermal modelling was employed, predicting cooling rates of 105–106 °C/s. Voids, mostly due to oxide films, were observed using Micro-CT in the as-fabricated condition. HIPping collapsed most voids, showing virtually no trace even after a further T6 treatment. Generally, the tensile properties of the majority of conditions were significantly better than in the cast + T6 equivalent alloy. Post-process machining was also found to improve the strength (compared to the as-fabricated surface). However, HIPping + T6 allowed the builds to achieve the required tensile properties, without surface machining. By assessing the influence of powder recycling, it was found that the void content linked to oxide layer formation increased following powder recycling, resulting in a drop in tensile properties. The interaction between the microstructure, surface condition, thermal post-processing, and fracture mode is discussed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
Khairallah, S. A., Anderson, A. T., Rubenchik, A., & King, W. E. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.02.014 · Cited by 2,766
Thijs, L., Kempen, K., Kruth, J.-P., & Van Humbeeck, J. (2013) · Acta Materialia · doi:10.1016/j.actamat.2012.11.052 · Cited by 1,917
Read, N., Wang, W., Essa, K., & Attallah, M. M. (2015) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2014.09.044 · Cited by 1,218
Self-citationBrandl, E., Heckenberger, U., Holzinger, V., & Buchbinder, D. (2012) · Materials & Design · doi:10.1016/j.matdes.2011.07.067 · Cited by 1,151
Mechanical Properties of AlSi10Mg Produced by Selective Laser Melting
Kempen, K., Thijs, L., Van Humbeeck, J., & Kruth, J.-P. (2012) · Physics Procedia · doi:10.1016/j.phpro.2012.10.059 · Cited by 849
Carter, L. N., Martin, C., Withers, P. J., & Attallah, M. M. (2014) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2014.06.172 · Cited by 751
Self-citationThe heat treatment of Al–Si–Cu–Mg casting alloys
Sjölander, E., & Seifeddine, S. (2010) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.03.020 · Cited by 559
Kunze, K., Etter, T., Grässlin, J., & Shklover, V. (2014) · Materials Science and Engineering A · doi:10.1016/j.msea.2014.10.003 · Cited by 515
Tang, H. P., Qian, M., Liu, N., Zhang, X. Z., Yang, G. Y., & Wang, J. (2015) · JOM · doi:10.1007/s11837-015-1300-4 · Cited by 483
Ardila, L. C., Garciandia, F., González-Díaz, J. B., Álvarez, P., Echeverria, A., Petite, M. M., Deffley, R., & Ochoa, J. (2014) · Physics Procedia · doi:10.1016/j.phpro.2014.08.152 · Cited by 268
Rosenthal, I., Stern, A., & Frage, N. (2014) · Metallography Microstructure and Analysis · doi:10.1007/s13632-014-0168-y · Cited by 256
Investigation of Aging Processes of Ti-6Al-4 V Powder Material in Laser Melting
Seyda, V., Kaufmann, N., & Emmelmann, C. (2012) · Physics Procedia · doi:10.1016/j.phpro.2012.10.057 · Cited by 166
Artificial ageing of Al–Si–Cu–Mg casting alloys
Sjölander, E., & Seifeddine, S. (2011) · Materials Science and Engineering A · doi:10.1016/j.msea.2011.06.036 · Cited by 130
Additive Manufacturing of Al-12Si Alloy Via Pulsed Selective Laser Melting
Chou, R., Milligan, J., Paliwal, M., & Brochu, M. (2015) · JOM · doi:10.1007/s11837-014-1272-9 · Cited by 129
Microstructural control during direct laser deposition of a β-titanium alloy
Qiu, C., Ravi, G. A., & Attallah, M. M. (2015) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2015.05.031 · Cited by 92
Self-citation
Cited by
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Aboulkhair, N. T., Simonelli, M., Parry, L., Ashcroft, I., Tuck, C., & Hague, R. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2019.100578 · Cited by 1,552
Beretta, S., & Romano, S. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.06.020 · Cited by 635
Making sustainable aluminum by recycling scrap: The science of “dirty” alloys
Raabe, D., Ponge, D., Uggowitzer, P. J., Roscher, M., Paolantonio, M., Liu, C., Antrekowitsch, H., Kozeschnik, E., Seidmann, D., Gault, B., et al. (2022) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.100947 · Cited by 626
Defects and anomalies in powder bed fusion metal additive manufacturing
Mostafaei, A., Zhao, C., He, Y., Reza Ghiaasiaan, S., Shi, B., Shao, S., Shamsaei, N., Wu, Z., Kouraytem, N., Sun, T., et al. (2022) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2021.100974 · Cited by 491
Metadata
- Authors
- Tradowsky, U., White, J., Ward, R. M., Read, N., Reimers, W., & Attallah, M. M.
- Venue
- Materials & Design
- Publisher
- Elsevier BV
- Published
- 2016-09
- Volume
- 105
- Pages
- 212-222
- ISSN
- 0264-1275 (ISSN-L)
- OpenAlex
- W2400659316
- Cited by
- 332
- References
- 17
- FWCI
- 21.84
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.