The DOI matches its Crossref record.
Residual stress and texture control in Ti-6Al-4V wire + arc additively manufactured intersections by stress relief and rolling
Open accessAbstract
Abstract Additively manufactured intersections have the theoretical risk to contain hydrostatic tensile residual stresses, which eventually cannot be thermally stress relieved. The stresses in Ti-6Al-4V wire + arc additively manufactured (WAAM) intersections are lower compared to single pass walls and stresses in continuous walls are larger compared to discontinuous walls with otherwise identical geometry. Thermal stress relief was found to virtually eliminate them. Inter-pass rolling can yield the desired grain refinement, without having any noteworthy influence on the development of residual stresses. The strain measurement itself by neutron diffraction is facilitated by the refined microstructure, because the otherwise textured microstructure produces anisotropic peak intensity, not allowing Pawley refinement. Without rolling, the 10 1 ¯ 1 and 10 1 ¯ 3 family of hcp planes are the only ones that diffract consistently in the three principal directions.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Additive manufacturing of Ti6Al4V alloy: A review
Liu, S., & Shin, Y. C. (2019) · Materials & Design · doi:10.1016/j.matdes.2018.107552 · Cited by 2,472
Current Status and Perspectives on Wire and Arc Additive Manufacturing (WAAM)
Rodrigues, T. A., Duarte, V., Miranda, R. M., Santos, T. G., & Oliveira, J. P. (2019) · Materials · doi:10.3390/ma12071121 · Cited by 779
State of the Art in Directed Energy Deposition: From Additive Manufacturing to Materials Design
Dass, A., & Moridi, A. (2019) · Coatings · doi:10.3390/coatings9070418 · Cited by 667
Surface post-treatments for metal additive manufacturing: Progress, challenges, and opportunities
Maleki, E., Bagherifard, S., Bandini, M., & Guagliano, M. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2020.101619 · Cited by 528
A review on wire and arc additive manufacturing of titanium alloy
Lin, Z., Song, K., & Yu, X. (2021) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.08.018 · Cited by 374
Metadata
- Authors
- Hönnige, J. R., Colegrove, P. A., Ahmad, B., Fitzpatrick, M. E., Ganguly, S., Lee, T. L., & Williams, S. W.
- Venue
- Materials & Design
- Publisher
- Elsevier BV
- Published
- 2018-07
- Volume
- 150
- Pages
- 193-205
- ISSN
- 0264-1275 (ISSN-L)
- OpenAlex
- W2795889866
- Cited by
- 200
- References
- 0
- FWCI
- 14.39
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Residual stress and texture control in Ti-6Al-4V wire + arc additively manufactured intersections by stress relief and rolling. https://app.cochat.ai/papers/10.1016/j.matdes.2018.03.065
- The paper
- Hönnige, J. R., Colegrove, P. A., Ahmad, B., Fitzpatrick, M. E., Ganguly, S., Lee, T. L., & Williams, S. W. (2018). Residual stress and texture control in Ti-6Al-4V wire + arc additively manufactured intersections by stress relief and rolling. Materials & Design. https://doi.org/10.1016/j.matdes.2018.03.065
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.