The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Effect of powder size distribution on densification and microstructural evolution of binder-jet 3D-printed alloy 625
Open accessAbstract
Binder-jet 3D-printing is a powder bed additive manufacturing process that selectively deposits binder on a powder bed layer-by-layer to fabricate a green part followed by a sintering step for densification. Gas-atomized alloy 625 powders of three different powder size distributions including 16–63 μm (full), 16–25 μm (fine) and 53–63 μm (coarse) powders were 3D-printed with green relative bulk densities of about 52%, 45% and 48%, respectively, followed by vacuum-sintering at temperatures between 1225 and 1300 °C for 4 h. For the fine and coarse powders with narrow size distribution, printing defects with high pore coordination numbers may form during the binder jetting process which cannot be removed during the final sintering stage even during supersolidus liquid phase sintering. However, the full particle size distribution gave higher green density with fewer large, highly coordinated pores so supersolidus liquid phase sintering was able to reach near-full density. Additionally, the fine powders gave non-uniform, anisotropic linear shrinkage during sintering which is unfavorable for designing complex structures. The results suggest that particle size distribution is a determining factor for supersolidus liquid phase sintering, pore removal and final microstructure, if printing parameters such as layer thickness, binder saturation, printhead binder droplet size and drying time are similar.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
NIH Image to ImageJ: 25 years of image analysis
Schneider, C. A., Rasband, W. S., & Eliceiri, K. W. (2012) · Nature Methods · doi:10.1038/nmeth.2089 · Cited by 64,638
Cited by
Binder jet 3D printing—Process parameters, materials, properties, modeling, and challenges
Mostafaei, A., Elliott, A. M., Barnes, J. E., Li, F., Tan, W., Cramer, C. L., Nandwana, P., & Chmielus, M. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100707 · Cited by 1,093
Self-citationBinder jetting: A review of process, materials, and methods
Ziaee, M., & Crane, N. B. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.05.031 · Cited by 819
Additive Manufacturing: A Comprehensive Review
Zhou, L., Miller, J., Vezza, J., Mayster, M., Raffay, M., Justice, Q., Al Tamimi, Z., Hansotte, G., Sunkara, L. D., & Bernat, J. (2024) · Sensors · doi:10.3390/s24092668 · Cited by 599
Metal Binder Jetting Additive Manufacturing: A Literature Review
Li, M., Du, W., Elwany, A., Pei, Z., & Ma, C. (2020) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4047430 · Cited by 334
Metadata
- Authors
- Mostafaei, A., Rodriguez De Vecchis, P., Nettleship, I., & Chmielus, M.
- Venue
- Materials & Design
- Publisher
- Elsevier BV
- Published
- 2019-01
- Volume
- 162
- Pages
- 375-383
- ISSN
- 0264-1275 (ISSN-L)
- OpenAlex
- W2902823367
- Cited by
- 236
- References
- 1
- FWCI
- 9.27
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effect of powder size distribution on densification and microstructural evolution of binder-jet 3D-printed alloy 625. https://app.cochat.ai/papers/10.1016/j.matdes.2018.11.051
- The paper
- Mostafaei, A., Rodriguez De Vecchis, P., Nettleship, I., & Chmielus, M. (2019). Effect of powder size distribution on densification and microstructural evolution of binder-jet 3D-printed alloy 625. Materials & Design. https://doi.org/10.1016/j.matdes.2018.11.051
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.