The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Micro-cable reinforced geopolymer composite for extrusion-based 3D printing
Abstract
Abstract Geopolymer has been applied to accommodate the rapid development of 3D printing in civil engineering practices and contributed this technique to reach its maximum eco-friendly potentials by eliminating the use of Portland cement. However, inherent problems with 3D printing concrete lie in the low tensile strength and poor ductility due to non-reinforcement, which greatly limit the application of 3D printing materials and structures. Hence, this study experimentally explores the feasibility of directly entraining a continuous micro steel cable (1.2 mm) during filaments (12 mm) deposition process, forming a reinforced geopolymer composite material. Three different printing path configurations are deigned to verify the applicability of micro-cable reinforced geopolymer composite for extrusion-based 3D printing. Flexural bending capacities of the proposed composite is measured and evaluated through four-point bending test. The results prove the well bonding and coordination of the micro-cable and geopolymer. Significant improvement of mechanical strength, toughness and post-cracking deformation of geopolymer composite are demonstrated.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Costs and carbon emissions for geopolymer pastes in comparison to ordinary portland cement
McLellan, B. C., Williams, R. P., Lay, J., van Riessen, A., & Corder, G. D. (2011) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2011.02.010 · Cited by 1,949
Cited by
Craveiro, F., Duarte, J. P., Bartolo, H., & Bartolo, P. J. (2019) · Automation in Construction · doi:10.1016/j.autcon.2019.03.011 · Cited by 455
Extrusion-based concrete 3D printing from a material perspective: A state-of-the-art review
Mohan, M. K., Rahul, A. V., De Schutter, G., & Van Tittelboom, K. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103855 · Cited by 384
Zhao, J., Tong, L., Li, B., Chen, T., Wang, C., Yang, G., & Zheng, Y. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2021.127085 · Cited by 369
Environmental and economic assessment on 3D printed buildings with recycled concrete
Han, Y., Yang, Z., Ding, T., & Xiao, J. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.123884 · Cited by 322
Metadata
- Authors
- Ma, G., Li, Z., Wang, L., & Bai, G.
- Venue
- Materials Letters
- Publisher
- Elsevier BV
- Published
- 2019-01
- Volume
- 235
- Pages
- 144-147
- ISSN
- 0167-577X (ISSN-L)
- OpenAlex
- W2895668282
- Cited by
- 196
- References
- 1
- FWCI
- 14.67
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Micro-cable reinforced geopolymer composite for extrusion-based 3D printing. https://app.cochat.ai/papers/10.1016/j.matlet.2018.09.159
- The paper
- Ma, G., Li, Z., Wang, L., & Bai, G. (2019). Micro-cable reinforced geopolymer composite for extrusion-based 3D printing. Materials Letters. https://doi.org/10.1016/j.matlet.2018.09.159
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.
