The DOI matches its Crossref record; 7 of the 7 references it cites were found in a registry or an index.
The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al–6.3Cu alloy
Open accessAbstract
Abstract Wire + Arc Additive Manufacture (WAAM) attracts great interest from the aerospace industry for producing components with aluminum alloys, particularly Al–Cu alloy of the 2000 series such as 2219 alloy. However the application is restricted by the low strength properties of the as-deposited WAAM metal. In this study two strengthening methods were investigated – inter-layer cold working and post-deposition heat treatment. Straight wall samples were prepared with 2319 aluminum alloy wire. Inter-layer rolling with loads of 15 kN, 30 kN and 45 kN were employed during deposition. The ultimate tensile strength (UTS) and yield strength (YS) of the inter-layer rolled alloy with 45 kN load can achieve 314 MPa and 244 MPa respectively. The influence of post-deposition T6 heat treatment was investigated on the WAAM alloy with or without rolling. Compared with inter-layer rolling, post-deposition heat treatment can provide much greater enhancement of the strength. After T6 treatment, the UTS and YS of both of the as-deposited and 45 kN rolled alloys exceeded 450 MPa and 305 MPa respectively, which are higher than the properties of the wrought 2219−T6 alloy. The strengthening mechanisms of this additively manufactured Al–6.3Cu alloy were investigated through microstructure analysis.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Application of modern aluminum alloys to aircraft
Starke, E. A., & Staley, J. T. (1996) · Progress in Aerospace Sciences · doi:10.1016/0376-0421(95)00004-6 · Cited by 1,463
(2017) · Corrosion Handbook · doi:10.1002/9783527610433.chb3603003 · Cited by 806
Microstructure and Mechanical Properties of Wire and Arc Additive Manufactured Ti-6Al-4V
Wang, F., Williams, S., Colegrove, P., & Antonysamy, A. A. (2013) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-012-1444-6 · Cited by 737
Self-citationInvestigation of the benefits of plasma deposition for the additive layer manufacture of Ti–6Al–4V
Martina, F., Mehnen, J., Williams, S., Colegrove, P. A., & Wang, F. (2012) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2012.02.002 · Cited by 641
Self-citation(1994) · Choice Reviews Online · doi:10.5860/choice.31-6064 · Cited by 637
Cong, B., Ding, J., & Williams, S. (2014) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-014-6346-x · Cited by 581
Self-citationColegrove, P. A., Coules, H., Fairman, J., Martina, F., Kashoob, T., Mamash, H., & Cozzolino, L. D. (2013) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2013.04.012 · Cited by 567
Cited by
Design for Additive Manufacturing: Trends, opportunities, considerations, and constraints
Thompson, M. K., Moroni, G., Vaneker, T., Fadel, G., Campbell, R. I., Gibson, I., Bernard, A., Schulz, J., Graf, P., Ahuja, B., et al. (2016) · CIRP Annals · doi:10.1016/j.cirp.2016.05.004 · Cited by 2,017
Wu, B., Pan, Z., Ding, D., Cuiuri, D., Li, H., Xu, J., & Norrish, J. (2018) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2018.08.001 · Cited by 1,577
Directed Energy Deposition (DED) Process: State of the Art
Ahn, D.-G. (2021) · International Journal of Precision Engineering and Manufacturing-Green Technology · doi:10.1007/s40684-020-00302-7 · Cited by 803
Current Status and Perspectives on Wire and Arc Additive Manufacturing (WAAM)
Rodrigues, T. A., Duarte, V., Miranda, R. M., Santos, T. G., & Oliveira, J. P. (2019) · Materials · doi:10.3390/ma12071121 · Cited by 779
Vafadar, A., Guzzomi, F., Rassau, A., & Hayward, K. (2021) · Applied Sciences · doi:10.3390/app11031213 · Cited by 748
Metadata
- Authors
- Gu, J., Ding, J., Williams, S. W., Gu, H., Bai, J., Zhai, Y., & Ma, P.
- Venue
- Materials Science and Engineering: A
- Publisher
- Elsevier BV
- Published
- 2016-01
- Volume
- 651
- Pages
- 18-26
- ISSN
- 0921-5093 (ISSN-L)
- OpenAlex
- W2218648427
- Cited by
- 413
- References
- 7
- FWCI
- 9.48
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al–6.3Cu alloy. https://app.cochat.ai/papers/10.1016/j.msea.2015.10.101
- The paper
- Gu, J., Ding, J., Williams, S. W., Gu, H., Bai, J., Zhai, Y., & Ma, P. (2016). The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al–6.3Cu alloy. Materials Science and Engineering: A. https://doi.org/10.1016/j.msea.2015.10.101
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.