The DOI matches its Crossref record.
Influence of post treatment on microstructure, porosity and mechanical properties of additive manufactured H13 tool steel
Abstract
Abstract Additive manufacturing (AM) is an attractive manufacturing technology in tooling applications. It provides unique opportunities to manufacture tools with complex shapes, containing inner channels for conformal cooling. In this investigation, H13, a widely used tool steel, was manufactured using a laser powder bed fusion method. Microstructure, tensile mechanical properties, hardness, and porosity of the AM H13 after stress relieve (SR), standard hardening and tempering (SR + HT), and hot isostatic pressing (SR + HIP + HT) were investigated. It was found that the microstructure of directly solidified colonies of prior austenite, which is typical for AM, disappeared after austenitizing at the hardening heat treatment. In specimens SR + HT and SR + HIP + HT, a microstructure similar to the conventional but finer was observed. Electron microscopy showed that SR and SR + HT specimens contained lack of fusion, and spherical gas porosity, which resulted in remarkable scatter in the observed elongation to break values. Application of HIP resulted in the highest strength values, higher than those observed for conventional H13 heat treated in the same way. The conclusion is that HIP promotes reduction of porosity and lack of fusion defects and can be efficiently used to improve the mechanical properties of AM H13 tool steel.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Steels in additive manufacturing: A review of their microstructure and properties
Bajaj, P., Hariharan, A., Kini, A., Kürnsteiner, P., Raabe, D., & Jägle, E. A. (2020) · Materials Science and Engineering: A · doi:10.1016/j.msea.2019.138633 · Cited by 1,020
Heat treatment for metal additive manufacturing
Laleh, M., Sadeghi, E., Revilla, R. I., Chao, Q., Haghdadi, N., Hughes, A. E., Xu, W., De Graeve, I., Qian, M., Gibson, I., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101051 · Cited by 538
Surface post-treatments for metal additive manufacturing: Progress, challenges, and opportunities
Maleki, E., Bagherifard, S., Bandini, M., & Guagliano, M. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2020.101619 · Cited by 528
Narasimharaju, S. R., Zeng, W., See, T. L., Zhu, Z., Scott, P., Jiang, X., & Lou, S. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.12.033 · Cited by 508
Al-Maharma, A. Y., Patil, S. P., & Markert, B. (2020) · Materials Research Express · doi:10.1088/2053-1591/abcc5d · Cited by 404
Metadata
- Authors
- Åsberg, M., Fredriksson, G., Hatami, S., Fredriksson, W., & Krakhmalev, P.
- Venue
- Materials Science and Engineering: A
- Publisher
- Elsevier BV
- Published
- 2019-01
- Volume
- 742
- Pages
- 584-589
- ISSN
- 0921-5093 (ISSN-L)
- OpenAlex
- W2886868493
- Cited by
- 184
- References
- 0
- FWCI
- 8.15
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Influence of post treatment on microstructure, porosity and mechanical properties of additive manufactured H13 tool steel. https://app.cochat.ai/papers/10.1016/j.msea.2018.08.046
- The paper
- Åsberg, M., Fredriksson, G., Hatami, S., Fredriksson, W., & Krakhmalev, P. (2019). Influence of post treatment on microstructure, porosity and mechanical properties of additive manufactured H13 tool steel. Materials Science and Engineering: A. https://doi.org/10.1016/j.msea.2018.08.046
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.