Heat treatment of Inconel 718 produced by selective laser melting: Microstructure and mechanical properties
The DOI matches its Crossref record; 22 of the 22 references it cites were found in a registry or an index.
Abstract
Abstract Inconel 718 (IN718) samples have been produced by selective laser melting (SLM). The effects of solution temperature, time and cooling rate as well as aging hardening on the microstructure and mechanical properties of SLMed IN718 have been studied. It is found that the as-fabricated IN718 is characterized with fine cellular dendrites with Laves phase precipitating in the subgrain boundaries, which is profoundly different from cast and wrought materials and needs different heat treatment schedules. The relationship between the minimum solution time and solution temperature is established and it provides a basis for the selection of solution treatment parameters. In addition, decreasing the cooling rate of solution treatment will contribute to the precipitation of strengthening phases. The precipitation temperatures of γ′ and γ″ are about the same for SLMed and wrought IN718, but the former has a faster aging response. The tensile properties of SLMed IN718 can be tuned in a large range by properly varying the microstructure. The highest elongation of 39.1% can be obtained after solution treatment (water quenching) without aging treatment and the highest yield and tensile strength (1374/1545 MPa) can be obtained after the direct aging treatment. The match of strength and ductility is able to be tailored by controlling the amount of strengthening phases, which can be realized by adjusting the cooling rate of solution treatment and aging time.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Vrancken, B., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2012.07.022 · Cited by 1,896
Microstructures and mechanical behavior of Inconel 718 fabricated by selective laser melting
Amato, K. N., Gaytan, S. M., Murr, L. E., Martinez, E., Shindo, P. W., Hernandez, J., Collins, S., & Medina, F. (2012) · Acta Materialia · doi:10.1016/j.actamat.2011.12.032 · Cited by 1,166
The microstructure and mechanical properties of deposited-IN718 by selective laser melting
Wang, Z., Guan, K., Gao, M., Li, X., Chen, X., & Zeng, X. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2011.10.107 · Cited by 812
Self-citationChlebus, E., Gruber, K., Kuźnicka, B., Kurzac, J., & Kurzynowski, T. (2015) · Materials Science and Engineering A · doi:10.1016/j.msea.2015.05.035 · Cited by 787
Zhang, D., Niu, W., Cao, X., & Liu, Z. (2015) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.06.021 · Cited by 723
Tucho, W. M., Cuvillier, P., Sjolyst-Kverneland, A., & Hansen, V. F. (2017) · Materials Science and Engineering A · doi:10.1016/j.msea.2017.02.062 · Cited by 682
Li, X. P., Wang, X. J., Saunders, M., Suvorova, A., Zhang, L. C., Liu, Y. J., Fang, M. H., Huang, Z. H., & Sercombe, T. B. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.05.017 · Cited by 654
Qi, H., Azer, M. N., & Ritter, A. M. (2009) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-009-9949-3 · Cited by 618
Lu, Y., Wu, S., Gan, Y., Huang, T., Yang, C., Junjie, L., & Lin, J. (2015) · Optics & Laser Technology · doi:10.1016/j.optlastec.2015.07.009 · Cited by 600
Popovich, V., Borisov, E. V., Popovich, A., Sufiiarov, V. S., Masaylo, D. V., & Alzina, L. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.10.075 · Cited by 580
Trosch, T., Strößner, J., Völkl, R., & Glatzel, U. (2016) · Materials Letters · doi:10.1016/j.matlet.2015.10.136 · Cited by 556
Vilaro, T., Colin, C., Bartout, J. D., Nazé, L., & Sennour, M. (2012) · Materials Science and Engineering: A · doi:10.1016/j.msea.2011.11.092 · Cited by 381
Microstructure and residual stress of laser rapid formed Inconel 718 nickel-base superalloy
Liu, F., Lin, X., Yang, G., Song, M., Chen, J., & Huang, W. (2010) · Optics & Laser Technology · doi:10.1016/j.optlastec.2010.06.015 · Cited by 348
Self-citationStructural characterization of the aged Inconel 718
Slama, C., & Abdellaoui, M. (2000) · Journal of Alloys and Compounds · doi:10.1016/s0925-8388(00)00789-1 · Cited by 327
Nadammal, N., Cabeza, S., Mishurova, T., Thiede, T. B., Kromm, A., Seyfert, C., Farahbod-Sternahl, L., Haberland, C., Schneider, J., Portella, P. D., et al. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.08.049 · Cited by 304
On the Precipitation Hardening of Selective Laser Melted AlSi10Mg
Aboulkhair, N. T., Tuck, C., Ashcroft, I., Maskery, I., & Everitt, N. M. (2015) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-015-2980-7 · Cited by 286
The mechanical and microstructural characteristics of laser-deposited IN718
Blackwell, P. L. (2005) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2005.05.005 · Cited by 266
Superior creep strength of a nickel-based superalloy produced by selective laser melting
Pröbstle, M., Neumeier, S., Hopfenmüller, J., Freund, L. P., Niendorf, T., Schwarze, D., & Göken, M. (2016) · Materials Science and Engineering A · doi:10.1016/j.msea.2016.07.061 · Cited by 243
Effect of weld cooling rate on Laves phase formation in Inconel 718 fusion zone
Manikandan, S. G. K., Sivakumar, D., Rao, K. P., & Kamaraj, M. (2013) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2013.09.006 · Cited by 180
Wang, X., & Chou, K. (2017) · Additive manufacturing · doi:10.1016/j.addma.2017.08.016 · Cited by 117
Microstructural evolution of Al–Cu–Mg–Ag alloy during homogenization
Liu, X. Y., Pan, Q. L., Fan, X. G., He, Y. B., Li, W. B., & Liang, W. J. (2009) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2009.05.046 · Cited by 111
Thermophysical properties of solid and liquid Inconel 718 alloy
Hosaeus, H., Seifter, A., Kaschnitz, E., & Pottlacher, G. (2001) · High Temperatures-High Pressures · doi:10.1068/htwu340 · Cited by 53
Cited by
Powder Bed Fusion of nickel-based superalloys: A review
Sanchez, S., Smith, P., Xu, Z., Gaspard, G., Hyde, C. J., Wits, W. W., Ashcroft, I. A., Chen, H., & Clare, A. T. (2021) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2021.103729 · Cited by 541
Heat treatment for metal additive manufacturing
Laleh, M., Sadeghi, E., Revilla, R. I., Chao, Q., Haghdadi, N., Hughes, A. E., Xu, W., De Graeve, I., Qian, M., Gibson, I., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101051 · Cited by 538
Post-Process Treatments for Additive-Manufactured Metallic Structures: A Comprehensive Review
Ge, J., Pillay, S., & Ning, H. (2023) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-023-08051-9 · Cited by 157
Metadata
- Authors
- Huang, W., Yang, J., Yang, H., Jing, G., Wang, Z., & Zeng, X.
- Venue
- Materials Science and Engineering: A
- Publisher
- Elsevier BV
- Published
- 2019-03
- Volume
- 750
- Pages
- 98-107
- ISSN
- 0921-5093 (ISSN-L)
- OpenAlex
- W2912115825
- Cited by
- 274
- References
- 22
- FWCI
- 14.79
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.