The DOI matches its Crossref record; 7 of the 7 references it cites were found in a registry or an index.
Influence of Powder Bed Preheating on Microstructure and Mechanical Properties of H13 Tool Steel SLM Parts
Open accessAbstract
Powder bed preheating is a promising development in selective laser melting (SLM), mainly applied to avoid large thermal stresses in the material. This study analyses the effect of in-process preheating on microstructure, mechanical properties and residual stresses during SLM of H13 tool steel. Sample parts are produced without any preheating and are compared to the corresponding parts made with preheating at 100°, 200°, 300°, and 400°C. Interestingly, internal stresses at the top surface of the parts evolve from compressive (-324MPa) without preheating to tensile stresses (371MPa) with preheating at 400°C. Nevertheless, application of powder bed preheating results in a more homogeneous microstructure with better mechanical properties compared to H13 SLM parts produced without preheating. The fine bainitic microstructure leads to hardness values of 650-700Hv and ultimate tensile strength of 1965MPa, which are comparable to or even better than those of conventionally made and heat treated H13 tool steel.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Laser additive manufacturing of metallic components: materials, processes and mechanisms
Gu, D. D., Meiners, W., Wissenbach, K., & Poprawe, R. (2012) · International Materials Reviews · doi:10.1179/1743280411y.0000000014 · Cited by 3,197
Selective Laser Melting of Crack-Free High Density M2 High Speed Steel Parts by Baseplate Preheating
Kempen, K., Vrancken, B., Buls, S., Thijs, L., Van Humbeeck, J., & Kruth, J.-P. (2014) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4028513 · Cited by 308
Self-citationNanocrystalline TiC-reinforced H13 steel matrix nanocomposites fabricated by selective laser melting
AlMangour, B., Grzesiak, D., & Yang, J. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.02.022 · Cited by 205
Microstructure and properties of FeCrMoVC tool steel produced by selective laser melting
Sander, J., Hufenbach, J., Giebeler, L., Wendrock, H., Kühn, U., & Eckert, J. (2016) · Materials & Design · doi:10.1016/j.matdes.2015.09.148 · Cited by 168
Direct additive laser manufacturing using gas- and water-atomised H13 tool steel powders
Pinkerton, A. J., & Li, L. (2004) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-003-1844-2 · Cited by 112
Cottam, R. E., Wang, J., & Luzin, V. (2014) · Journal of materials research/Pratt's guide to venture capital sources · doi:10.1557/jmr.2014.190 · Cited by 98
Eser, A., Broeckmann, C., & Şimşir, C. (2015) · Computational Materials Science · doi:10.1016/j.commatsci.2015.11.020 · Cited by 53
Cited by
Steels in additive manufacturing: A review of their microstructure and properties
Bajaj, P., Hariharan, A., Kini, A., Kürnsteiner, P., Raabe, D., & Jägle, E. A. (2020) · Materials Science and Engineering: A · doi:10.1016/j.msea.2019.138633 · Cited by 1,020
Residual Stress in Metal Additive Manufacturing
Li, C., Liu, Z. Y., Fang, X. Y., & Guo, Y. B. (2018) · Procedia CIRP · doi:10.1016/j.procir.2018.05.039 · Cited by 708
Fayazfar, H., Salarian, M., Rogalsky, A., Sarker, D., Russo, P., Paserin, V., & Toyserkani, E. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.02.018 · Cited by 665
Additive manufacturing of steels: a review of achievements and challenges
Haghdadi, N., Laleh, M., Moyle, M., & Primig, S. (2021) · Journal of Materials Science · doi:10.1007/s10853-020-05109-0 · Cited by 622
Heat treatment for metal additive manufacturing
Laleh, M., Sadeghi, E., Revilla, R. I., Chao, Q., Haghdadi, N., Hughes, A. E., Xu, W., De Graeve, I., Qian, M., Gibson, I., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101051 · Cited by 538
Metadata
- Authors
- Mertens, R., Vrancken, B., Holmstock, N., Kinds, Y., Kruth, J.-P., & Van Humbeeck, J.
- Venue
- Physics Procedia
- Publisher
- Elsevier BV
- Published
- 2016
- Volume
- 83
- Pages
- 882-890
- ISSN
- 1875-3892 (ISSN-L)
- OpenAlex
- W2520771015
- Cited by
- 301
- References
- 7
- FWCI
- 14.46
- Type
- journal article
- Language
- en
- Open access
- diamond
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Influence of Powder Bed Preheating on Microstructure and Mechanical Properties of H13 Tool Steel SLM Parts. https://app.cochat.ai/papers/10.1016/j.phpro.2016.08.092
- The paper
- Mertens, R., Vrancken, B., Holmstock, N., Kinds, Y., Kruth, J.-P., & Van Humbeeck, J. (2016). Influence of Powder Bed Preheating on Microstructure and Mechanical Properties of H13 Tool Steel SLM Parts. Physics Procedia. https://doi.org/10.1016/j.phpro.2016.08.092
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.