The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Electrospun poly lactic acid (PLA) fibres: Effect of different solvent systems on fibre morphology and diameter
Open accessAbstract
The selection of an appropriate non-hazardous solvent or solvent system is essential to determine the rheological properties and electrospinnability of the solution, the productivity, and the morphology of nanofibres. In this study, poly lactic acid (PLA) solutions were prepared in various pure solvents and binary-solvent systems to investigate the effect of different solution properties on nanofibre morphology and diameter. Viscosity, conductivity and surface tension of each solution were measured. Nanofibre morphology was observed by scanning electron microscopy (SEM). Of all the solvent systems used acetone/dimethylformamide gave the highest fibre productivity and finest defect-free nanofibres. Therefore this solvent system was studied in more detail, varying the solvent ratio. Also the polymer concentration in this solvent system was varied to investigate the effect on nanofibre morphology and solution properties. Morphological investigations were done in correlation with rheological measurements: beaded nanofibrous structures were collected from solutions with concentration around the critical chain entanglement concentration (Ce), while defect-free nanofibres were produced when the concentration was increased to about twice the entanglement concentration. Further investigation of the effect of the PLA concentration on the elastic (G′) and the plastic (G″) moduli showed a sudden increase of the elastic moduli (G′) at the critical chain entanglement concentration. The results showed that the solvent properties, boiling point, viscosity, conductivity and surface tension, have a significant effect on process productivity, morphology and diameter distribution of the PLA nanofibres.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A Literature Review of Poly(Lactic Acid)
Garlotta, D. (2001) · Journal of Polymers and the Environment · doi:10.1023/a:1020200822435 · Cited by 3,707
Cited by
Yang, G., Li, X., He, Y., Ma, J., Ni, G., & Zhou, S. (2018) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2017.12.003 · Cited by 336
Wen, P., Zhu, D.-H., Feng, K., Liu, F.-J., Lou, W.-Y., Li, N., Zong, M.-H., & Wu, H. (2016) · Food Chemistry · doi:10.1016/j.foodchem.2015.10.043 · Cited by 330
Porous electrospun polycaprolactone (PCL) fibres by phase separation
Katsogiannis, K. A. G., Vladisavljević, G. T., & Georgiadou, S. (2015) · European Polymer Journal · doi:10.1016/j.eurpolymj.2015.01.028 · Cited by 266
Self-citationRashedi, S., Afshar, S., Rostami, A., Ghazalian, M., & Nazockdast, H. (2021) · International Journal of Polymeric Materials and Polymeric Biomaterials · doi:10.1080/00914037.2020.1740987 · Cited by 36
Metadata
- Authors
- Casasola, R., Thomas, N. L., Trybala, A., & Georgiadou, S.
- Venue
- Polymer
- Publisher
- Elsevier BV
- Published
- 2014-09
- Volume
- 55
- Issue
- 18
- Pages
- 4728-4737
- ISSN
- 0032-3861 (ISSN-L)
- OpenAlex
- W1998213702
- Cited by
- 382
- References
- 1
- FWCI
- 6.76
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Electrospun poly lactic acid (PLA) fibres: Effect of different solvent systems on fibre morphology and diameter. https://app.cochat.ai/papers/10.1016/j.polymer.2014.06.032
- The paper
- Casasola, R., Thomas, N. L., Trybala, A., & Georgiadou, S. (2014). Electrospun poly lactic acid (PLA) fibres: Effect of different solvent systems on fibre morphology and diameter. Polymer. https://doi.org/10.1016/j.polymer.2014.06.032
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.