The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Electrically conductive nanocomposites for fused deposition modelling
Open accessAbstract
Abstract An acrylonitrile-butadiene-styrene (ABS) matrix was melt compounded with various amounts (from 1 to 8 wt%) of multi-walled carbon nanotubes (MWCNT) predispersed in an ABS carrier. The resulting materials were then i) compression molded (CM) to obtain plaques or ii) extruded in filaments used to feed a fused deposition modelling (FDM) machine. 3D printed samples were obtained under three different orientations. The nanofiller addition within the ABS matrix caused a remarkable increase of both stiffness and stress at yield of the bulk samples, accompanied by a strong reduction of the elongation at break. The mechanical properties of 3D printed samples resulted to be strongly dependent on the printing orientation. The addition of CNTs was very effective in improving the electrical conductivity with respect to neat ABS even at the smallest filler content. The FDM process determined a partial loss in the electrical conductivity of ABS nanocomposites, with a marked dependency on the printing orientation. For CNT amounts higher than 4 wt%, CM samples manifested a rapid heating by Joule effect, while the process was less efficient in the printed samples. CNT addition has high impact on thermal properties, resulting in a decrease of specific heat and a increase of thermal diffusivity and conductivity. Like observed for electric conductivity FDM also influences properties of thermal diffusivity and conductivity, resulted by a possible orientation of CNT.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Flash Method of Determining Thermal Diffusivity, Heat Capacity, and Thermal Conductivity
Parker, W. J., Jenkins, R. J., Butler, C. P., & Abbott, G. L. (1961) · Journal of Applied Physics · doi:10.1063/1.1728417 · Cited by 3,978
Studies on thermal and mechanical properties of polyimide–clay nanocomposites
Agag, T., Koga, T., & Takeichi, T. (2001) · Polymer · doi:10.1016/s0032-3861(00)00824-7 · Cited by 599
Cited by
Recent developments in polymers/polymer nanocomposites for additive manufacturing
Wu, H., Fahy, W. P., Kim, S., Kim, H., Zhao, N., Pilato, L., Kafi, A., Bateman, S., & Koo, J. H. (2020) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100638 · Cited by 531
Recent Developments in Fused Deposition Modeling-Based 3D Printing of Polymers and Their Composites
Rahim, T. N. A. T., Abdullah, A. M., & Md Akil, H. (2019) · Polymer Reviews · doi:10.1080/15583724.2019.1597883 · Cited by 452
Additive manufacturing of polymeric composites from material processing to structural design
Yuan, S., Li, S., Zhu, J., & Tang, Y. (2021) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2021.108903 · Cited by 267
Zhang, C., Li, Y., Kang, W., Liu, X., & Wang, Q. (2021) · SusMat · doi:10.1002/sus2.11 · Cited by 256
Metadata
- Authors
- Dorigato, A., Moretti, V., Dul, S., Unterberger, S. H., & Pegoretti, A.
- Venue
- Synthetic Metals
- Publisher
- Elsevier BV
- Published
- 2017-04
- Volume
- 226
- Pages
- 7-14
- ISSN
- 0379-6779 (ISSN-L)
- OpenAlex
- W2585078138
- Cited by
- 178
- References
- 2
- FWCI
- 7.79
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Electrically conductive nanocomposites for fused deposition modelling. https://app.cochat.ai/papers/10.1016/j.synthmet.2017.01.009
- The paper
- Dorigato, A., Moretti, V., Dul, S., Unterberger, S. H., & Pegoretti, A. (2017). Electrically conductive nanocomposites for fused deposition modelling. Synthetic Metals. https://doi.org/10.1016/j.synthmet.2017.01.009
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.