The DOI matches its Crossref record; 12 of the 12 references it cites were found in a registry or an index.
Preparation and characterization of biodegradable PLA polymeric blends
Abstract
The purpose of this study was to fine-tune the mechanical properties of high molecular-weight poly-L-lactic acid (PLLA), especially to increase its toughness without sacrificing too much of its original strength. Besides of its long degradation time, PLLA is usually hard and brittle, which hinders its usage in medical applications, i.e., orthopedic and dental surgery. Some modifications, such as the addition of plasticizers or surfactants/compatibilizers, are usually required to improve its original properties. PDLLA can degrade quickly due to its amorphous structure, thus shortening the degradation time of PLLA/PDLLA blends. Blends of biodegradable poly-L-lactic acid (PLLA) and poly-DL-lactic acid (PDLLA) or polycaprolactone (PCL), in addition to a third component, the surfactant-a copolymer of ethylene oxide and propylene oxide, were prepared by blending these three polymers at various ratios using dichloromethane as a solvent. The weight percentages of PLLA/PDLLA (or PCL) blends were 100%/0%, 80%/20%, 60%/40%, 50%/50%, 40%/60%, 20%/80% and 0%/100%, respectively. Physical properties such as the crystalline melting point, glass transition point (T(g)), phase behavior, degradation behavior, and other mechanical properties were characterized by thermogravimetric analysis, differential scanning calorimetry (DSC), infrared spectroscopy, gel permeation chromatography, and dynamic mechanical analysis (DMA). DSC data indicate that PLLA/PDLLA blends without the surfactant had two T(g)'s. With the addition of the surfactant, there was a linear shift of the single T(g) as a function of composition, with lower percentages of PLLA producing lower glass transition temperatures indicating that better miscibility had been achieved. DMA data show that the 40/60 PLLA/PDLLA blends without the surfactant had high elastic modulus and elongation, and similar results were observed after adding 2% surfactant into the blends. The 50/50 PLLA/PDLLA/2% surfactant blend had the highest elastic modulus, yield strength, and break strength compared with other ratios of PLLA/PDLLA/2% surfactant blends. The elongation at break of 50/50 PLLA/PDLLA was similar to that of PLLA. Again, the elongation at break of 50/50 PLLA/PDLLA/2% surfactant was almost 1.2-1.9 times higher than that of 50/50 PLLA/PDLLA and PLLA. Elongation of PLLA increased with the addition of PCL, but the strength decreased at the same time. In conclusions, adding PDLLA and surfactant to PLLA via solution-blending may be an effective way to make PLLA tougher and more suitable to use in orthopedic or dental applications.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“However, while a variety of synthetic methods have been studied for industrial and commercial use, none of these is simple, easy to operate, or economical.”
From Synthesis and Biological Application of Polylactic Acid (2020) · cites this paper as [9]
In the citing paper
“Commercially feasible methods for obtaining and purifying lactide involve steps such as condensing lactic acid at 115–179 °C, removing the condensed water, and removing the mesolactic acid and low-molecular polymer through recrystallization to obtain pure l- or d, l-lactide with high molecular weight [9,43,44].”
From Synthesis and Biological Application of Polylactic Acid (2020) · cites this paper as [9]
Citations
Cites
Biodegradable poly(lactic acid) polymers
Kulkarni, R. K., Moore, E. G., Hegyeli, A. F., & Leonard, F. (1971) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820050305 · Cited by 799
In vitro and in vivo degradation of porous poly(dl-lactic-co-glycolic acid) foams
Lu, L., Peter, S. J., D. Lyman, M., Lai, H.-L., Leite, S. M., Tamada, J. A., Uyama, S., Vacanti, J. P., Langer, R., & Mikos, A. G. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00047-8 · Cited by 668
Frazza, E. J., & Schmitt, E. E. (1971) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820050207 · Cited by 572
Biodegradable bone repair materials. Synthetic polymers and ceramics.
Hollinger, J. O., & Battistone, G. C. (1986) · PubMed · Cited by 486
Biodegradable Bone Repair Materials: Synthetic Polymers and Ceramics
HOLLINGER, J. O., & BATTISTONE, G. C. (1986) · Clinical Orthopaedics and Related Research · doi:10.1097/00003086-198606000-00046 · Cited by 381
Tonino, A., Davidson, C., Klopper, P., & Linclau, L. (1976) · The Journal of Bone and Joint Surgery. British volume · doi:10.1302/0301-620x.58b1.1270486 · Cited by 338
Tsuji, H., & Ikada, Y. (1996) · Journal of Applied Polymer Science · doi:10.1002/(sici)1097-4628(19960627)60:13<2367::aid-app8>3.0.co;2-c · Cited by 202
Long-term in vivo degradation and bone reaction to various polylactides. 1. One-year results.
Mainil-Varlet, P., Rahn, B., & Gogolewski, S. (1997) · Biomaterials · doi:10.1016/s0142-9612(96)00126-3 · Cited by 134
Aslan, S., Calandrelli, L., Laurienzo, P., Malinconico, M., & Migliaresi, C. (2000) · Journal of Materials Science · doi:10.1023/a:1004787326273 · Cited by 123
Sawhney, A. S., & Hubbell, J. A. (1990) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820241011 · Cited by 118
Research works printed but not linked: 2
- Cochran, 1969, Effect of internal fixation plates on mechanical deformation of bone, Surg Forum, 20, 469
- Case, 1994, Will my polymer mix? Methods for studying polymer miscibility, Trends Polym Sci, 2, 256
Cited by
Poly(lactic acid) modifications
Rasal, R. M., Janorkar, A. V., & Hirt, D. E. (2010) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2009.12.003 · Cited by 2,204
Polymer blends and composites from renewable resources
Yu, L., Dean, K., & Li, L. (2006) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2006.03.002 · Cited by 2,107
“[59] prepared blends of biodegradable PLLA and PDLLA, in addition to a third component, the surfactant—a copolymer of ethylene oxide and propylene oxide—at various ratios using dichloromethane as a solvent.”
MethodPoly(lactic acid)—Mass production, processing, industrial applications, and end of life
Castro-Aguirre, E., Iñiguez-Franco, F., Samsudin, H., Fang, X., & Auras, R. (2016) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2016.03.010 · Cited by 1,329
Elfaleh, I., Abbassi, F., Habibi, M., Ahmad, F., Guedri, M., Nasri, M., & Garnier, C. (2023) · Results in Engineering · doi:10.1016/j.rineng.2023.101271 · Cited by 1,034
Mundargi, R. C., Babu, V. R., Rangaswamy, V., Patel, P., & Aminabhavi, T. M. (2008) · Journal of Controlled Release · doi:10.1016/j.jconrel.2007.09.013 · Cited by 1,025
“, are explored for CR applications [26,27].”
Metadata
- Authors
- Chen, C.-C., Chueh, J.-Y., Tseng, H., Huang, H.-M., & Lee, S.-Y.
- Affiliations
- Taipei Medical University (TW)
- Wan Fang Hospital (TW)
- Corresponding author
- Lee, Sheng-Yang
- Venue
- Biomaterials
- Publisher
- Elsevier BV
- Published
- 2003-03
- Volume
- 24
- Issue
- 7
- Pages
- 1167-1173
- ISSN
- 0142-9612 (ISSN-L)
- OpenAlex
- W2084344211
- Cited by
- 583
- References
- 12
- Citations by year
- 2026: 12 · 2025: 22 · 2024: 19 · 2023: 22 · 2022: 33 · 2021: 29 · 2020: 34 · 2019: 25 · 2018: 36 · 2017: 28 · 2016: 33 · 2015: 31 · 2014: 36 · 2013: 37 · 2012: 41
- FWCI
- 4.64
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- www.elsevier.com/tdm/userlicense/1.0/ (tdm)
- Locations
- Biomaterials (publishedVersion)
- PubMed (publishedVersion)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Engineering › Biomedical Engineering › Bone Tissue Engineering Materials
- Keywords
- poly(L-lactic acid), poly(D,L-lactide), polycaprolactone, polymer blends, glass transition temperature, phase behavior, mechanical properties, toughness, biodegradable polymers, biodegradation
- MeSH terms
- Biocompatible Materials, Biodegradation, Environmental, Ethylene Oxide, Polyesters, Surface-Active Agents
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Preparation and characterization of biodegradable PLA polymeric blends. https://app.cochat.ai/papers/10.1016/s0142-9612(02)00466-0
- The paper
- Chen, C.-C., Chueh, J.-Y., Tseng, H., Huang, H.-M., & Lee, S.-Y. (2003). Preparation and characterization of biodegradable PLA polymeric blends. Biomaterials. https://doi.org/10.1016/s0142-9612(02)00466-0
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.