Student or educator? Sign up with your school email and get 6 months of Pro free.
Cited by 318

The DOI matches its Crossref record; 27 of the 27 references it cites were found in a registry or an index.

Speciation of the most soluble phases in a sequential extraction procedure adapted for geochemical studies of copper sulfide mine waste

Open access
Dold, Bernhard·2003·Journal of Geochemical Exploration

Abstract

Abstract Sequential extractions are widely used for exploration purposes and to study element speciation in systems such as soil and sediments, and more recently to understand the complex biogeochemical element cycling in mine waste environments. This method is however often the focus of criticism due to uncertainty in the selectivity of specific leaches utilized. In this study, a procedure is presented how sequential extractions can be adapted to specific mineralogy in order to increase the selectivity and the accuracy of geochemical data interpretation. The application of dissolution kinetic tests and the control of dissolved phases in sequential extractions by X-ray diffraction (XRD) and differential X-ray diffraction (DXRD) indicate which minerals are dissolved in each leach. This information is crucial for the interpretation of geochemical data obtained from sequential extractions and enables to increase the selectivity of the sequence applied. A seven-step sequence was adapted to the specific secondary and primary mineralogy of mine tailings from Cu-sulfide ores, both from porphyry copper and from Fe-oxide Cu–Au deposits. As result of the study, the following seven-step sequence shows best selectivity for the aim of the study of Cu-sulfide mine waste: Step 1 liberates the water-soluble fraction (1.0-g sample into 50-ml deionized H2O shake for 1 h at room temperature [RT]) dissolving gypsum and metal salts (e.g., chalcanthite (CuSO4·5H2O), pickeringite (MgAl2(SO4)4·22H2O)). Step 2 liberates the exchangeable fraction (1 M NH4-acetate, pH 4.5, shaken for 2 h, RT) as adsorbed ions, but also dissolves calcite and breaks down a typical secondary vermiculite-type mixed-layer mineral from the low pH oxidation zone. Step 3 addresses the Fe(III) oxyhydroxides fraction (0.2 M NH4-oxalate, pH 3.0, shaken for 1 h in darkness, RT) and dissolves schwertmannite, two-line ferrihydrite, Mn-hydroxides, secondary jarosite partially, as well as goethite acid mine drainage formed. Step 4 dissolves the Fe(III) oxides fraction (0.2 M NH4-oxalate, pH 3.0, heat in water bath 80 °C for 2 h) and removes all secondary ferric minerals occurring as higher ordered ferrihydrite (e.g., six-line), goethite, primary and secondary jarosite, natrojarosite, and primary hematite. Step 5 consists of a change from reducing to oxidizing condition and is performed by a H2O2 leach (35% H2O2 heat in water bath for 1 h), which dissolves organic matter and supergene Cu-sulfides such as covellite and chalcocite–digenite. Step 6 (KClO3 and HCl, followed by 4 M HNO3 boiling) dissolves primary sulfides and Step 7 (HCl, HF, HClO4, HNO3) the residual fraction (silicates). The application of this extraction sequence to 5 Cu-sulfide mine tailings have shown that sequential extractions can be a powerful tool for detection of element mobilization and retention processes. This is especially the case in dry climates, where it is difficult to obtain pore-water geochemistry. A detailed mineralogical study should however go hand in hand with every geochemical study of mine waste to ensure the accuracy of the geochemical interpretations.

Overview

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1016/s0375-6742(03)00182-1

Cites

27 of 27 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 27 references

Cited by

See all 318

Metadata

Authors
Dold, B.
Venue
Journal of Geochemical Exploration
Publisher
Elsevier BV
Published
2003-08
Volume
80
Issue
1
Pages
55-68
ISSN
0375-6742 (ISSN-L)
OpenAlex
W2025084080
Cited by
318
References
27
FWCI
4.55
Type
journal article
Language
en
Open access
green

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Speciation of the most soluble phases in a sequential extraction procedure adapted for geochemical studies of copper sulfide mine waste. https://app.cochat.ai/papers/10.1016/s0375-6742(03)00182-1
The paper
Dold, B. (2003). Speciation of the most soluble phases in a sequential extraction procedure adapted for geochemical studies of copper sulfide mine waste. Journal of Geochemical Exploration. https://doi.org/10.1016/s0375-6742(03)00182-1

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.