Catalyst Slurry Preparation Using a Hydrodynamic Cavitation Dispersion Method for Polymer Electrolyte Fuel Cells
The DOI matches its Crossref record; 22 of the 22 references it cites were found in a registry or an index.
Abstract
In this study, we used a hydrodynamic cavitation method to disperse catalyst slurries for polymer electrolyte fuel cells (PEFCs) for the first time. Continuous flow processing using this method enables the mass production of a membrane–electrode assembly (MEA) for PEFCs. Here, a hydrodynamic cavitation method was compared with a batch-type ball-milling method that achieves a state-of-the-art performance Pt/C catalyst layer. Additionally, this method was compared with a simple sonication method to discuss the importance of the catalyst slurry dispersion. As a result, the MEA prepared using a well-dispersed slurry by the hydrodynamic cavitation method exhibited a high fuel cell performance comparable to that of the MEA prepared by the well-established ball-milling method and much higher than that of the MEA prepared using an insufficiently dispersed slurry by the simple sonication method. Thus, the results obtained demonstrate the applicability of a continuous flow, hydrodynamic cavitation method for MEA production in PEFCs.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Appropriate dispersion process could effectively break up the large agglomerates, reduce the size of agglomerates, and improve the dispersion of catalyst and ionomer in solvent, which will maximize TPB, avoid the formation of cracks, as well as improve the pore volume of CL and thus the mass transport [24,156] (Figure 9b,e).”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [24]
In the citing paper
“However, if the dispersion process is insufficient, the large agglomerates in the catalyst ink cannot be broken down, leading to an inhomogeneous CL or even causing cracking in the CL (Figure 9a,d) [24,154].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [24]
In the citing paper
“For the ink with low viscosity or low solid concentration, tip sonication, bath sonication, or their combination, and ball milling are applicable; however, for a viscous ink or an ink with high solid concentration, ball milling may be more suitable, e.g., ca. 10 wt.% solid concentration [24,28].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [24]
In the citing paper
“Furthermore, the hydrodynamic cavitation method [24], the planetary mixer [154], or high-pressure homogenization [158] have been applied to disperse catalyst ink recently.”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [24]
In the citing paper
“The large agglomerates may result from the poor dispersion of catalyst ink [24], or the hydrophobic compounds formed from the alcohol oxidation catalyzed by Pt, e.g., 1,1-dipropoxypropane and propyl propionate, which promote the aggregation of catalyst agglomerates in the ink [81].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [24]
1 more claim about this paper
Create a free account to see every claim other papers make about this one.
Citations
Cites
Gasteiger, H. A., Kocha, S. S., Sompalli, B., & Wagner, F. T. (2005) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2004.06.021 · Cited by 4,876
Park, Y.-C., Tokiwa, H., Kakinuma, K., Watanabe, M., & Uchida, M. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.02.091 · Cited by 389
Properties of Nafion® NR-211 membranes for PEMFCs
Peron, J., Mani, A., Zhao, X., Edwards, D., Adachi, M., Soboleva, T., Shi, Z., Xie, Z., Navessin, T., & Holdcroft, S. (2010) · Journal of Membrane Science · doi:10.1016/j.memsci.2010.03.025 · Cited by 352
Uchida, M., Fukuoka, Y., Sugawara, Y., Eda, N., & Ohta, A. (1996) · Journal of The Electrochemical Society · doi:10.1149/1.1836988 · Cited by 309
Theoretical and Experimental Sonochemistry Involving Inorganic Systems
(2011) · Springer eBooks · doi:10.1007/978-90-481-3887-6 · Cited by 208
A green, rapid and size-controlled production of high-quality graphene sheets by hydrodynamic forces
Liu, L., Shen, Z., Yi, M., Zhang, X., & Ma, S. (2014) · RSC Advances · doi:10.1039/c4ra05635c · Cited by 141
The importance of ultrasonic parameters in the preparation of fuel cell catalyst inks
Pollet, B. G., & Goh, J. T. E. (2014) · Electrochimica Acta · doi:10.1016/j.electacta.2013.09.160 · Cited by 117
An in situ technique for analyzing ionomer coverage in catalyst layers
Iden, H., & Ohma, A. (2013) · Journal of Electroanalytical Chemistry · doi:10.1016/j.jelechem.2013.01.026 · Cited by 107
Simulation of capillary shrinkage cracking in cement-like materials
Slowik, V., Hübner, T., Schmidt, M., & Villmann, B. (2009) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2009.05.004 · Cited by 79
Tamaki, T., Kuroki, H., Ogura, S., Fuchigami, T., Kitamoto, Y., & Yamaguchi, T. (2015) · Energy & Environmental Science · doi:10.1039/c5ee02450a · Cited by 76
Self-citationInfluence of the solvent in anode catalyst ink on the performance of a direct methanol fuel cell
Kim, J.-H., Ha, H. Y., Oh, I., Hong, S., & Lee, H. (2004) · Journal of Power Sources · doi:10.1016/j.jpowsour.2004.03.058 · Cited by 75
Highly durable fuel cell electrodes based on ionomers dispersed in glycerol
Kim, Y. S., Welch, C. F., Mack, N. H., Hjelm, R. P., Orler, E. B., Hawley, M. E., Lee, K. S., Yim, S.-D., & Johnston, C. M. (2014) · Phys. Chem. Chem. Phys. · doi:10.1039/c4cp00496e · Cited by 75
Novel Approach of Producing Oil in Water Emulsion Using Hydrodynamic Cavitation Reactor
Ramisetty, K. A., Pandit, A. B., & Gogate, P. R. (2014) · Industrial & Engineering Chemistry Research · doi:10.1021/ie502753d · Cited by 63
Tang, S. Y., & Manickam, S. (2012) · AIChE Journal · doi:10.1002/aic.13800 · Cited by 57
Graphene production via supercritical fluids
Gao, H., & Hu, G. (2016) · RSC Advances · doi:10.1039/c5ra15568a · Cited by 47
Ink Degradation and Its Effects on the Crack Formation of Fuel Cell Catalyst Layers
Uemura, S., Yoshida, T., Koga, M., Matsumoto, H., Yang, X., Shinohara, K., Sasabe, T., & Hirai, S. (2019) · Journal of The Electrochemical Society · doi:10.1149/2.0411902jes · Cited by 34
Hashimasa, Y., & Numata, T. (2015) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2015.04.031 · Cited by 33
Modeling for PEFC MEAs Based on Reaction Rate on Pt Surface and Microstructures of Catalyst Layers
Limjeerajarus, N., Nishiyama, Y., Ohashi, H., Ito, T., & Yamaguchi, T. (2009) · JOURNAL OF CHEMICAL ENGINEERING OF JAPAN · doi:10.1252/jcej.09we006 · Cited by 32
Self-citationKimura, K., Sakamoto, T., Mukai, T., Ikeuchi, Y., Yamashita, N., Onishi, K., Asami, K., & Yanagida, M. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.0241802jes · Cited by 32
Self-citationTamaki, T., Koshiishi, A., Sugawara, Y., Kuroki, H., Oshiba, Y., & Yamaguchi, T. (2018) · Journal of Applied Electrochemistry · doi:10.1007/s10800-018-1193-3 · Cited by 18
Self-citationKuroki, H., Tamaki, T., & Yamaguchi, T. (2016) · Journal of The Electrochemical Society · doi:10.1149/2.0971608jes · Cited by 17
Self-citationKuroki, H., & Yamaguchi, T. (2006) · Journal of The Electrochemical Society · doi:10.1149/1.2202114 · Cited by 15
Self-citation
Research works printed but not linked: 3
- Ministry of Economy, Trade and Industry, Japan. The Basic Hydrogen Strategy. http://www.meti.go.jp/english/press/2017/pdf/1226_003b.pdf (accessed April 4, 2019).
- Kocha S. S., 2010, Handbook of Fuel Cells
- 10.1016/j.apcatb.2004.06.021 · DOI · Paper page
Cited by
A review on hydrodynamic cavitation disinfection: The current state of knowledge
Sun, X., Liu, J., Ji, L., Wang, G., Zhao, S., Yoon, J. Y., & Chen, S. (2020) · Science of The Total Environment · doi:10.1016/j.scitotenv.2020.139606 · Cited by 185
The Controllable Design of Catalyst Inks to Enhance PEMFC Performance: A Review
Guo, Y., Pan, F., Chen, W., Ding, Z., Yang, D., Li, B., Ming, P., & Zhang, C. (2021) · Electrochemical Energy Reviews · doi:10.1007/s41918-020-00083-2 · Cited by 175
Du, S., Li, W., Wu, H., Abel Chuang, P.-Y., Pan, M., & Sui, P.-C. (2020) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2020.07.241 · Cited by 88
Liu, H., Ney, L., Zamel, N., & Li, X. (2022) · Applied Sciences · doi:10.3390/app12083776 · Cited by 85
“((a–c) Modified with permission from [156], Copyright (2019), American Chemical Society; (d–e) Reprinted with p rmission from [24], Copyright (2019), America Chemical Society; (f) Reprinted from [159], Copyright (2014), with permission from Elsevier).”
BackgroundMethodInfluentialChen, F., Guo, L., Long, D., Luo, S., Song, Y., Wang, M., Li, L., Chen, S., & Wei, Z. (2024) · Journal of the American Chemical Society · doi:10.1021/jacs.4c10742 · Cited by 89
Metadata
- Authors
- Kuroki, H., Onishi, K., Asami, K., & Yamaguchi, T.
- Affiliations
- Tokyo Institute of Technology (JP)
- Nihon Spindle Manufacturing Co., Ltd. (Japan) (JP)
- Corresponding author
- Kuroki, Hidenori
- Yamaguchi, Takeo
- Venue
- Industrial & Engineering Chemistry Research
- Publisher
- American Chemical Society (ACS)
- Published
- 2019-09-16
- Volume
- 58
- Issue
- 42
- Pages
- 19545-19550
- ISSN
- 0888-5885 (ISSN-L)
- 1520-5045
- OpenAlex
- W2974033067
- Cited by
- 45
- References
- 22
- Citations by year
- 2026: 7 · 2025: 10 · 2024: 10 · 2023: 5 · 2022: 3 · 2021: 5 · 2020: 5
- FWCI
- 1.17
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- Locations
- Industrial & Engineering Chemistry Research (publishedVersion)
- Funders
- Core Research for Evolutional Science and Technology (JPMJCR1543)
- Kanagawa Institute of Industrial Science and Technology
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Physics and Astronomy › Acoustics and Ultrasonics › Ultrasound and Cavitation Phenomena
- Keywords
- hydrodynamic cavitation, proton exchange membrane fuel cells, membrane electrode assembly, continuous flow processing, ball milling, sonication
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.