Sequential Crystallization and Multicrystalline Morphology in PE- b -PEO- b -PCL- b -PLLA Tetrablock Quarterpolymers
Open accessThe DOI matches its Crossref record; 67 of the 67 references it cites were found in a registry or an index; 1 of the 10 sources its claims cite were checked for support.
Abstract
small-angle X-ray scattering/wide-angle X-ray scattering (SAXS/WAXS), and atomic force microscopy (AFM). The direct comparison of the results obtained with these different techniques allows the precise identification of the crystallization sequence of the blocks upon cooling from the melt. SAXS indicated that Q1 is melt miscible, while Q2 is weakly segregated in the melt but breaks out during crystallization. According to WAXS and DSC results, the blocks follow a sequence as they crystallize: PLLA first, then PE, then PCL, and finally PEO in the case of the Q1 quarterpolymer; in Q2, the PLLA block is not able to crystallize due to its low isotacticity. Although the temperatures at which the PEO and PCL blocks and the PE and PLLA blocks crystallize overlap, the analysis of the intensity changes measured by WAXS and PLOM experiments allows identifying each of the crystallization processes. The quarterpolymer Q1 remarkably self-assembles during crystallization into tetracrystalline banded spherulites, where four types of different lamellae coexist. Nanostructural features arising upon sequential crystallization are found to have a relevant impact on the mechanical properties. Nanoindentation measurements show that storage modulus and hardness of the Q1 quarterpolymer significantly deviate from those of the stiff PE and PLLA blocks, approaching typical values of compliant PEO and PCL. Results are mainly attributed to the low crystallinity of the PE and PLLA blocks. Moreover, the Q2 copolymer exhibits inferior mechanical properties than Q1, and this can be related to the PE block within Q1 that has thinner crystal lamellae according to its much lower melting point.
Overview
CoChat Summary
TL;DR
Two novel PE-b-PEO-b-PCL-b-PLLA tetrablock quarterpolymers were synthesized and characterized, showing sequential crystallization of up to four blocks and, for Q1, tetracrystalline banded spherulites. Q1 crystallizes PLLA, PE, PCL, and PEO sequentially, whereas Q2’s PLLA block does not crystallize due to low isotacticity, yielding tricrystalline microspherulites and lower mechanical properties.
Key findings
- Q1 (PE187.1-b-PEO3715.1-b-PCL2610.4-b-PLLA197.6) is melt-miscible by SAXS; WAXS/DSC show crystallization sequence PLLA at 84 °C, PE at 82 °C, PCL at 42 °C, and PEO at 24 °C, forming tetracrystalline banded spherulites with Maltese crosses and negative signs.
- Q2 (PE299.5-b-PEO268.8-b-PCL237.6-b-PLLA227.3) is weakly segregated in the melt by SAXS with breakout crystallization; PLLA does not crystallize (84% isotactic tetrads), and the sequence is PE at 104 °C, PCL at 32 °C, and PEO at 20 °C, giving tricrystalline microspherulites.
- Nanoindentation shows both quarterpolymers have low storage modulus and hardness (E′ ≤ 1 GPa, H ≤ 50 MPa), attributed to low PE and PLLA crystallinity; Q2 is inferior to Q1, related to thinner PE lamellae/lower PE melting point. Q1 crystallinity estimates include PE 7% and PLLA 4% (Table S9).
- SAXS indicates Q1 has no diffraction peaks in the melt, while Q2 shows a sharp low-q peak and weak second-order reflection consistent with lamellar phase segregation in the melt.
Methods
- Q1 and Q2 were synthesized by one-pot polyhomologation plus ring-opening polymerization using a catalyst-switch strategy (organic/metal for Q1, organic/organic for Q2); corresponding triblock, diblock, and homopolymer precursors were also studied.
- Characterization used nonisothermal DSC, PLOM, simultaneous in situ SAXS/WAXS at ALBA, AFM, and nanoindentation; most cooling/heating experiments were at 20 °C/min, and WAXS normalized intensity versus temperature was used to assign block crystallization.
- Nanoindentation used dynamic testing at 400 nm depth, with at least 50 indents averaged for E′ and H; AFM samples were spin-coated thin films cooled from the melt at 50 or 20 °C/min.
Limitations
- Stated: overlapping PE/PLLA and PEO/PCL crystallization and melting transitions make individual crystallinity estimation difficult; AFM cannot clearly distinguish lamellae of the different blocks; PEO spherulites approached millimeter scale, so average E′ and H values were meaningless.
- Stated: experimental determination of χ for terpolymers or quarterpolymers has not been reported, so segregation-strength estimates are approximate and based on literature solubility parameters.
- Evident: conclusions rest on only two quarterpolymers and mostly 20 °C/min thermal protocols, so generality across compositions and cooling rates is limited; cooling-rate variation was not systematically explored except in AFM sample preparation.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures














Verification
Claims the paper makes
0 Valid · 1 Not valid · 5 Not checked · 96 Own results and interpretations
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In the first quarterpolymer (Q1), all blocks are able to crystallize.”
§ Sequential Crystallization and Multicrystalline Morphology in PE-b-PEO-b-PCL-b-PLLA Tetrablock Quarterpolymers > Results and Discussion > Nonisothermal Crystallization by DSC
plainSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
In the paper
“The formation of tetracrystalline quarterpolymers was confirmed by 1H NMR spectroscopy and gel-permeation chromatography.54”
§ Sequential Crystallization and Multicrystalline Morphology in PE-b-PEO-b-PCL-b-PLLA Tetrablock Quarterpolymers > Experimental Section > Materials
What the sources say
- Not checked — no full text of the sourcecites [54] source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Due to monomer purity and possible side reactions, the polyethylene block precursors are not 100% linear.”
§ Sequential Crystallization and Multicrystalline Morphology in PE-b-PEO-b-PCL-b-PLLA Tetrablock Quarterpolymers > Experimental Section > Materials
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“SAXS indicated that Q1 is melt miscible, while Q2 is weakly segregated in the melt but breaks out during crystallization.”
§ Sequential Crystallization and Multicrystalline Morphology in PE-b-PEO-b-PCL-b-PLLA Tetrablock Quarterpolymers > Abstract
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Although the temperatures at which the PEO and PCL blocks and the PE and PLLA blocks crystallize overlap”
§ Sequential Crystallization and Multicrystalline Morphology in PE-b-PEO-b-PCL-b-PLLA Tetrablock Quarterpolymers > Abstract
plainstates an associationSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
31 more claims
Create a free account to see all 102 claims and every source verdict.
- It may state two separate claims as one. 59
- Probably not a substantial claim. 11
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Sequential Crystallization and Multicrystalline Morphology in PE-b-PEO-b-PCL-b-PLLA Tetrablock Quarterpolymers > Results and Discussion > Mechanical Properties by Indentation
“PEO that represents 68% of the molar fraction in the copolymer.”
§ Sequential Crystallization and Multicrystalline Morphology in PE-b-PEO-b-PCL-b-PLLA Tetrablock Quarterpolymers > Experimental Section > Materials
“Subscripts denote composition in wt %, and superscripts denote Mn values in kg/mol.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Sequential Crystallization and Multicrystalline Morphology in PE-b-PEO-b-PCL-b-PLLA Tetrablock Quarterpolymers > Abstract
“Moreover, the Q2 copolymer exhibits inferior mechanical properties than Q1, and this can be related to the PE block within Q1 that has thinner crystal lamellae according to its much lower melting point.”
§ Sequential Crystallization and Multicrystalline Morphology in PE-b-PEO-b-PCL-b-PLLA Tetrablock Quarterpolymers > Results and Discussion > Mechanical Properties by Indentation
“Concerning the Q2 copolymer, lower E′ and H values are found with respect to Q1 (Figure 13), and this could be explained as due to the inferior mechanical properties of the PE9.5 block in Q2 with respect to the PE7.1 one in Q1 (Table S9).”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Sequential Crystallization and Multicrystalline Morphology in PE-b-PEO-b-PCL-b-PLLA Tetrablock Quarterpolymers > Abstract
“″organocatalyst/metal catalyst switch″ (Q1 sample, 96% isotactic tetrads)”
§ Sequential Crystallization and Multicrystalline Morphology in PE-b-PEO-b-PCL-b-PLLA Tetrablock Quarterpolymers > Experimental Section > Materials
“Q1 was synthesized by the organic/metal ″catalyst switch″ (t-BuP4/DPP/Sn[Oct]2) strategy (isotactic tetrads 98%).”
Citations
Cites
Oliver, W. C., & Pharr, G. M. (1992) · Journal of Materials Research · doi:10.1557/jmr.1992.1564 · Cited by 26,961
Hiemenz, P. C., & Lodge, T. P. (2007) · CRC Press eBooks · doi:10.1201/9781420018271 · Cited by 948
Zhang, J., Tashiro, K., Tsuji, H., & Domb, A. J. (2008) · Macromolecules · doi:10.1021/ma0706071 · Cited by 913
Phase Behaviour and Morphologies of Block Copolymers
Abetz, V., & Simon, P. F. W. (2005) · Advances in Polymer Science · doi:10.1007/12_004 · Cited by 361
Transport and structural characteristics of crosslinked poly(ethylene oxide) rubbers
LIN, H., WAGNER, E., SWINNEA, J., FREEMAN, B., PAS, S., HILL, A., KALAKKUNNATH, S., & KALIKA, D. (2006) · Journal of Membrane Science · doi:10.1016/j.memsci.2005.09.040 · Cited by 327
Nanoindentation and the dynamic characterization of viscoelastic solids
Herbert, E. G., Oliver, W. C., & Pharr, G. M. (2008) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/41/7/074021 · Cited by 271 · cited 2×
“57,58 Poisson ’ s ratio was taken as 0.4.”
InfluentialCastillo, R. V., & Müller, A. J. (2009) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2009.03.002 · Cited by 253
Self-citationCrystal structure of poly(iε-caprolactone)
Hu, H., & Dorset, D. L. (1990) · Macromolecules · doi:10.1021/ma00223a017 · Cited by 225
Measuring substrate-independent modulus of thin films
Hay, J., & Crawford, B. (2011) · Journal of Materials Research · doi:10.1557/jmr.2011.8 · Cited by 216 · cited 1×
“This is especially important in those samples in which the spherulite dimension was similar to the size of the volume of deformation (which approximately covers a hemisphere with a radius of 20 μ m for an indentation depth of 1 μ m 59 ).”
Hadjichristidis, N., Pitsikalis, M., & Iatrou, H. (2005) · Advances in Polymer Science · doi:10.1007/12_005 · Cited by 209
Self-citation
Research works printed but not linked: 4
- Van Horn R. M., 2018, Polym. Cryst., 1, e10039
- Bao J., 2020, J. Polym. Sci., 1
- Palacios J. K., 2016, R. Soc. Chem. Adv., 6, 4739
- Palacios J. K., 2017, Macromolecules, 50, 7261
Cited by
Zhang, C., Si, W., Wang, Z., et al. (2024) · Journal of the American Chemical Society · doi:10.1021/jacs.4c00881 · Cited by 42
Meng, J., Boschetto, F., Yagi, S., Marin, E., Adachi, T., Chen, X.-F., Pezzotti, G., Sakurai, S., Yamane, H., & Xu, H. (2022) · Materials & Design · doi:10.1016/j.matdes.2022.110781 · Cited by 40
He, M., Hsu, Y., & Uyama, H. (2024) · Applied Materials Today · doi:10.1016/j.apmt.2024.102057 · Cited by 32
Gao, Z., Zhang, X., Zheng, B., Gu, J., & Tong, Z. (2025) · Journal of the American Chemical Society · doi:10.1021/jacs.4c15602 · Cited by 24
Crystallinity of Amphiphilic PE-b-PEG Copolymers
Bistac, S. B., Brogly, M., & Bindel, D. (2022) · Polymers · doi:10.3390/polym14173639 · Cited by 26
Metadata
- Authors
- Matxinandiarena, E., Múgica, A., Tercjak, A., Ladelta, V., Zapsas, G., Hadjichristidis, N., Cavallo, D., Flores, A., & Müller, A. J.
- Affiliations
- University of the Basque Country (ES)
- King Abdullah University of Science and Technology (SA)
- University of Genoa (IT)
- Consejo Superior de Investigaciones Científicas (ES)
- Ikerbasque (ES)
- Corresponding author
- Müller, Alejandro J.
- ORCID
- Venue
- Macromolecules
- Publisher
- American Chemical Society (ACS)
- Published
- 2021-07-23
- Volume
- 54
- Issue
- 15
- Pages
- 7244-7257
- ISSN
- 0024-9297 (ISSN-L)
- 1520-5835
- PMC
- PMC9159653
- OpenAlex
- W3185076943
- Cited by
- 16
- References
- 67
- Citations by year
- 2026: 2 · 2025: 5 · 2024: 2 · 2023: 2 · 2022: 5
- FWCI
- 0.80
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- Macromolecules (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- Communities in ADDI (University of the Basque Country) (submittedVersion, other-oa)
- DIGITAL.CSIC (Spanish National Research Council (CSIC)) (submittedVersion)
- Hispana (submittedVersion, other-oa)
- CINECA IRIS Institutial Research Information System (University of Genoa) (submittedVersion)
- King Abdullah University of Science and Technology Repository (King Abdullah University of Science and Technology) (submittedVersion, other-oa)
- Funders
- Ministerio de Econom??a y Competitividad (MAT2017-83014-C2-1-P, MAT2017-88382-P)
- Eusko Jaurlaritza (IT1309-19)
- Horizon 2020 Framework Programme (778092)
- Abraham Lincoln Brigade Archives (u2020084441)
- BIODEST project
- Topics
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Materials Science › Materials Chemistry › Block Copolymer Self-Assembly
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Keywords
- sequential crystallization, block copolymers, poly(ethylene-alt-propylene), poly(ethylene oxide), polycaprolactone, poly(L-lactic acid), banded spherulites, lamellar thickness, melt miscibility, isotacticity, mechanical properties, storage modulus, hardness, nanoindentation, crystallization sequence
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Sequential Crystallization and Multicrystalline Morphology in PE- b -PEO- b -PCL- b -PLLA Tetrablock Quarterpolymers. https://app.cochat.ai/papers/10.1021/acs.macromol.1c01186
- The paper
- Matxinandiarena, E., Múgica, A., Tercjak, A., Ladelta, V., Zapsas, G., Hadjichristidis, N., Cavallo, D., Flores, A., & Müller, A. J. (2021). Sequential Crystallization and Multicrystalline Morphology in PE- b -PEO- b -PCL- b -PLLA Tetrablock Quarterpolymers. Macromolecules. https://doi.org/10.1021/acs.macromol.1c01186
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.