The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
3D Printing of Carbon Nanotubes-Based Microsupercapacitors
Abstract
A novel 3D printing procedure is presented for fabricating carbon-nanotubes (CNTs)-based microsupercapacitors. The 3D printer uses a CNTs ink slurry with a moderate solid content and prints a stream of continuous droplets. Appropriate control of a heated base is applied to facilitate the solvent removal and adhesion between printed layers and to improve the structure integrity without structure delamination or distortion upon drying. The 3D-printed electrodes for microsupercapacitors are characterized by SEM, laser scanning confocal microscope, and step profiler. Effect of process parameters on 3D printing is also studied. The final solid-state microsupercapacitors are assembled with the printed multilayer CNTs structures and poly(vinyl alcohol)-H 3 PO 4 gel as the interdigitated microelectrodes and electrolyte. The electrochemical performance of 3D printed microsupercapacitors is also tested, showing a significant areal capacitance and excellent cycle stability.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Jiang, J., Li, Y., Liu, J., Huang, X., Yuan, C., & Lou, X. W. (. (2012) · Advanced Materials · doi:10.1002/adma.201202146 · Cited by 2,473
Cited by
A review of topology optimization for additive manufacturing: Status and challenges
ZHU, J., ZHOU, H., WANG, C., ZHOU, L., YUAN, S., & ZHANG, W. (2021) · Chinese Journal of Aeronautics · doi:10.1016/j.cja.2020.09.020 · Cited by 874
Self-citation3D printing technologies for electrochemical energy storage
Zhang, F., Wei, M., Viswanathan, V. V., Swart, B., Shao, Y., Wu, G., & Zhou, C. (2017) · Nano Energy · doi:10.1016/j.nanoen.2017.08.037 · Cited by 494
Conductive nanomaterials for 2D and 3D printed flexible electronics
Kamyshny, A., & Magdassi, S. (2019) · Chemical Society Reviews · doi:10.1039/c8cs00738a · Cited by 469
3D Printing for Electrochemical Energy Applications
Browne, M. P., Redondo, E., & Pumera, M. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.9b00783 · Cited by 434
3D Printed Sensors for Biomedical Applications: A Review
Han, T., Kundu, S., Nag, A., & Xu, Y. (2019) · Sensors · doi:10.3390/s19071706 · Cited by 266
Metadata
- Authors
- Yu, W., Zhou, H., Li, B. Q., & Ding, S.
- Venue
- ACS Applied Materials & Interfaces
- Publisher
- American Chemical Society (ACS)
- Published
- 2017-01-30
- Volume
- 9
- Issue
- 5
- Pages
- 4597-4604
- ISSN
- 1944-8244 (ISSN-L)
- 1944-8252
- OpenAlex
- W2574533880
- Cited by
- 227
- References
- 1
- FWCI
- 7.55
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: 3D Printing of Carbon Nanotubes-Based Microsupercapacitors. https://app.cochat.ai/papers/10.1021/acsami.6b13904
- The paper
- Yu, W., Zhou, H., Li, B. Q., & Ding, S. (2017). 3D Printing of Carbon Nanotubes-Based Microsupercapacitors. ACS Applied Materials & Interfaces. https://doi.org/10.1021/acsami.6b13904
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.
