Baroplastic Effect of Aliphatic Polyester Block Copolymers for Degradation-Free Multicycle Processing of Poly( l -lactide)
Open accessThe DOI matches its Crossref record; 24 of the 24 references it cites were found in a registry or an index; none of the 2 sources its claims cite is checked for support yet.
Abstract
High Resolution Image Download MS PowerPoint Slide Advancing sustainable plastics is crucial to achieving a circular plastic economy. Baroplastics, block copolymers exhibiting order–disorder transitions under pressure, allow polymer processing at ambient temperatures, reducing energy use and avoiding thermal degradation. Their application, however, has been limited by structural constraints. This study introduces poly( ε -caproclactone-random-5-ethyleneketal ε -caprolactone)- block -poly( l -lactide) (PmCL- b -PLLA) as a “ baroplasticizer ” for nonbaroplastic PLLA. Blending with the block polymers lowered PLLA’s flow temperature by up to 100 °C (160 to 60 °C at 50 MPa) while preserving molecular weight after repeated pressure cycles, ensuring recyclability. The improved formability would arise from a pressure-induced ordered (solid)-to-disordered (melt/solid) phase transition. This work eliminates structural constraints in baroplastics, enabling broader low-temperature processing applications and advancing sustainable polymer technologies.
Overview
CoChat Summary
TL;DR
PmCL-b-PLLA block copolymers act as “baroplasticizers” for nonbaroplastic PLLA, lowering its flow temperature under 50 MPa from 160 °C to about 60 °C while preserving molecular weight after repeated pressure cycles. The effect is attributed to a reversible pressure-induced ordered-to-disordered phase transition.
Key findings
- Adding PmCL-b-PLLA to PLLA reduced the flow temperature at 50 MPa; PmCL-b-PLLA40(50) lowered it from a maximum of 160 °C to approximately 60 °C, a decrease of about 100 °C. For PLLA/PmCL-b-PLLA40 blends with 10, 20, 30, 40, and 50 wt % block copolymer, flow temperatures were 136, 131, 82, 74, and 62 °C, respectively.
- Block copolymer composition mattered: PmCL-b-PLLA40(50) and PmCL-b-PLLA50(50) flowed at 62 and 65 °C, whereas PmCL-b-PLLA60(50) exhibited fluidity above 117 °C under the same conditions. The block copolymers alone flowed at 2, 10, and 35 °C for PmCL-b-PLLA40, -50, and -60, respectively, at 50 MPa.
- Repeated pressure processing did not significantly change flow temperature after four cycles. SEC showed no changes in molecular weight or Đ for the blend, while the PLLA matrix alone decreased in molecular weight from 74,600 to 41,500 after four pressure-processing cycles at >160 °C.
- DSC and SAXS indicated a reversible pressure-induced phase transition: for PmCL-b-PLLA50(50), a SAXS peak appeared after annealing at 100 °C with Λave = 31.4 nm, larger than the block copolymer alone (20.9 nm); peak intensity decreased under pressure and recovered after pressure release.
Methods
- PmCL-b-PLLAs were synthesized by two-step ring-opening polymerization using SnOct2; the soft segment was ε-caprolactone and TOSUO in 50/50 molar ratio, and hard PLLA fractions were 38, 49, and 57 wt % (designated PmCL-b-PLLA40, -50, and -60). All block copolymers had similar molecular weight of approximately 50,000 and Đ = 1.2.
- PLLA/PmCL-b-PLLA blends were prepared by chloroform dissolution at weight ratios of 1:9, 2:8, 3:7, 4:6, and 5:5, recovered by reprecipitation in methanol, and dried under reduced pressure for at least 12 h.
- Flow behavior was measured with a capillary rheometer at 50 MPa and heating at 5 °C min–1, defining flow temperature as the point where shear rate increased abruptly or viscosity decreased sharply. Thermal properties were measured by DSC, molecular weight by SEC, and nanostructure by SAXS using a NANOPIX3.5 instrument with a custom pressure cell.
Limitations
- The paper states that further quantitative investigations of nanostructural changes under pressure should be conducted to fully comprehend the pressure-induced flow.
- Evident from the text: SAXS at ambient conditions showed no periodic structure for the PmCL-b-PLLA50(50) blend, and a clear peak was observed only after annealing at 100 °C, so the ambient-state microphase structure was not directly resolved by SAXS.
- The proposed mechanism in Figure 6, with PmCL-rich domains randomly dispersed throughout the blend, is described as hypothesized rather than directly proven.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures






Verification
Claims the paper makes
0 Valid · 1 Not valid · 3 Not checked · 46 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The T m and X c of PLLA remained essentially unchanged after a PmCL-b-PLLA/PLLA blend was subjected to multiple cycles of pressure processing.”
§ Baroplastic Effect of Aliphatic Polyester Block Copolymers for Degradation-Free Multicycle Processing of Poly(l‑lactide) > Experimental Section > Measurements
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“When the block copolymers with different soft/hard segment ratios were blended with PLLA at the same weight ratio, the flow temperature of the blend decreased as the hard segment fraction in the block copolymer decreased.”
§ Baroplastic Effect of Aliphatic Polyester Block Copolymers for Degradation-Free Multicycle Processing of Poly(l‑lactide) > Experimental Section > Measurements
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The flow temperature of PLLA decreased monotonically with increasing PmCL-b-PLLA content in the polymer blends.”
§ Baroplastic Effect of Aliphatic Polyester Block Copolymers for Degradation-Free Multicycle Processing of Poly(l‑lactide) > Experimental Section > Measurements
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In contrast, the molecular weight of the PLLA matrix itself changed after four pressure-processing cycles at the flow temperature (>160 °C), with the molecular weight decreasing from 74,600 to 41,500 as shown in Figure .”
§ Baroplastic Effect of Aliphatic Polyester Block Copolymers for Degradation-Free Multicycle Processing of Poly(l‑lactide) > Experimental Section > Measurements
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In addition, no changes in molecular weight and Đ (M w/M n) were observed for the polymer blend in size exclusion chromatography (SEC) analyses.”
§ Baroplastic Effect of Aliphatic Polyester Block Copolymers for Degradation-Free Multicycle Processing of Poly(l‑lactide) > Experimental Section > Measurements
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
19 more claims
Create a free account to see all 50 claims and every source verdict.
- It may state two separate claims as one. 18
- Probably not a substantial claim. 11
Citations
Cites
Plastics of the Future? The Impact of Biodegradable Polymers on the Environment and on Society
Haider, T. P., Völker, C., Kramm, J., Landfester, K., & Wurm, F. R. (2019) · Angewandte Chemie International Edition · doi:10.1002/anie.201805766 · Cited by 1,591
Signori, F., Coltelli, M.-B., & Bronco, S. (2009) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2008.10.004 · Cited by 503
Phase Behavior of Block Copolymer/Homopolymer Blends
Matsen, M. W. (1995) · Macromolecules · doi:10.1021/ma00121a011 · Cited by 483 · cited 1×
“26 When a high molecular weight homopolymer is added, the domain of that component swells significantly, and the other component shrinks to a smaller domain.”
Processability and mechanical properties of extensively recycled high density polyethylene
Oblak, P., Gonzalez-Gutierrez, J., Zupančič, B., Aulova, A., & Emri, I. (2015) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2015.01.012 · Cited by 239
Mechanistic aspects of the thermal degradation of poly(lactic acid) and poly(β-hydroxybutyric acid)
Kopinke, F.-D., & Mackenzie, K. (1997) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(97)00022-3 · Cited by 176 · cited 1×
“22,23 This paper demonstrates that the baroplastic PmCL-b -PLLA serves as a “ baroplasticizer ” for nonbaroplastic PLLA.”
Low-temperature processing of ‘baroplastics’ by pressure-induced flow
González-León, J. A., Acar, M. H., Ryu, S., Ruzette, A.-V., & Mayes, A. M. (2003) · Nature · doi:10.1038/nature02140 · Cited by 134
Multiblock Copolymers for Recycling Polyethylene–Poly(ethylene terephthalate) Mixed Waste
Nomura, K., Peng, X., Kim, H., Jin, K., Kim, H. J., Bratton, A. F., Bond, C. R., Broman, A. E., Miller, K. M., & Ellison, C. J. (2020) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b20242 · Cited by 105
Introduction to Polymer Blends
Utracki, L. A. (2003) · Springer eBooks · doi:10.1007/0-306-48244-4_1 · Cited by 97
Shrivastava, A. (2018) · Elsevier eBooks · doi:10.1016/b978-0-323-39500-7.00002-2 · Cited by 88
A simple model for baroplastic behavior in block copolymer melts
Ruzette, A.-V., Banerjee, P., Mayes, A. M., & Russell, T. P. (2001) · The Journal of Chemical Physics · doi:10.1063/1.1361072 · Cited by 70
Research works printed but not linked: 3
- Steinbüchel A., 2001, Biopolymers (Wiley), 24
- Stevenson J. F., 1989, Comprehensive Polymer Science, 7, 303
- Tadmor, Z.; Gogos, C. G. Principles of Polymer Processing ; John Wiley & Sons, 2006; pp 35–45.
Cited by
Phase stability in pressure-responsive block copolymer/homopolymer blends
Degaki, H., Taniguchi, I., Deguchi, S., & Koga, T. (2026) · Polymer · doi:10.1016/j.polymer.2026.129886 · Cited by 1
Self-citation(8) Deep-Sea-Inspired Chemistry: Materials Innovation from Deep-Sea Extreme Environment
Tachioka, M., Taniguchi, I., Tsuyoshi, K. O. G. A., & Deguchi, S. (2026) · Journal of The Adhesion Society of Japan · doi:10.11618/adhesion.62.42
Self-citationJiao, Y., Jin, Y., Isobe, A., Fujita, M., Araki, T., Suzuki, Y., Otsuka, Y., Kamimura, N., Masai, E., & Michinobu, T. (2026) · Polymer Journal · doi:10.1038/s41428-026-01193-2
Tachioka, M., Tsudome, M., Nakamura, A., & Deguchi, S. (2026) · Bulletin of the Chemical Society of Japan · doi:10.1093/bulcsj/uoag107
Self-citation
Metadata
- Authors
- Sharma, N., Koga, T., Deguchi, S., & Taniguchi, I.
- Affiliations
- Japan Agency for Marine-Earth Science and Technology (JP)
- Corresponding author
- Taniguchi, Ikuo
- Venue
- ACS Macro Letters
- Publisher
- American Chemical Society (ACS)
- Published
- 2025-10-28
- Volume
- 14
- Issue
- 11
- Pages
- 1716-1720
- ISSN
- 2161-1653 (ISSN-L)
- PMC
- PMC12632162
- OpenAlex
- W4415628925
- Cited by
- 4
- References
- 22
- Citations by year
- 2026: 4
- FWCI
- 0.84
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- Locations
- ACS Macro Letters (publishedVersion, cc-by-nc-nd)
- Europe PMC (PubMed Central) (publishedVersion, cc-by-nc-nd)
- PubMed (publishedVersion)
- Institutional Repositories DataBase (IRDB) (submittedVersion)
- Kyoto University Research Information Repository (Kyoto University) (submittedVersion, cc-by-nc-nd)
- Funders
- Core Research for Evolutional Science and Technology (JPMJCR21L4)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Materials Science › Materials Chemistry › Block Copolymer Self-Assembly
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Keywords
- poly(L-lactic acid), order-disorder transition, pressure-induced phase transition, low-temperature processing, polymer recycling, flow temperature, circular plastic economy, sustainable plastics
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Baroplastic Effect of Aliphatic Polyester Block Copolymers for Degradation-Free Multicycle Processing of Poly( l -lactide). https://app.cochat.ai/papers/10.1021/acsmacrolett.5c00483
- The paper
- Sharma, N., Koga, T., Deguchi, S., & Taniguchi, I. (2025). Baroplastic Effect of Aliphatic Polyester Block Copolymers for Degradation-Free Multicycle Processing of Poly( l -lactide). ACS Macro Letters. https://doi.org/10.1021/acsmacrolett.5c00483
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.