Effect of the Fast Pyrolysis Temperature on the Primary and Secondary Products of Lignin
The DOI matches its Crossref record; 3 of the 3 references it cites were found in a registry or an index.
Abstract
This paper presents results on the primary pyrolysis products of organosolv lignin at temperatures between 360 and 700 °C. To study the primary products, a vacuum screen heater (heating rate of 8000 °C/s, deep vacuum of 0.7 mbar, and very fast cooling at the wall temperature of −100 °C) was used. The effect of the temperature on the primary and secondary lignin products was studied with a fluidized-bed pyrolysis reactor ( T reactor between 330 and 580 °C) with pine wood. The results obtained with the screen heater show that the primary products of lignin were oligomers. Between 450 and 700 °C, the yield of these oligomers was very high, between 80 and 90%. After formation, the oligomers left the particle by evaporation or thermal ejection. Monophenols and other light compounds were formed by secondary reactions inside the particle or in the vapor phase. In the fluidized-bed reactor, significant quantities of lignin oligomers were formed along with monophenols, water, and other light compounds. The changes on the yield and composition of the lignin-derived oligomers as a function of the pyrolysis temperature are reported. The lignin oligomers were isolated by cold-water precipitation and analyzed with thermogravimetry (TG), Fourier transform infrared (FTIR) spectroscopy, pyrolysis–gas chromatography/mass spectrometry (Py–GC/MS), electrospray ionization–mass spectrometry (ESI–MS), gel permeation chromatography (GPC), and proton nuclear magnetic resonance ( 1 H NMR). The yield of lignin-derived oligomers reached a maximum between 450 and 580 °C. The differential thermogravimetry (DTG) results show the existence of three major peaks, which where maximal between 450 and 480 °C, indicating that not only the yield but also the structure of the lignin oligomers changed at higher pyrolysis temperatures. Py–GC/MS and 1 H NMR results indicated that, as the temperature increased, the content of methoxylated phenols decreased and the content of alkylated phenols increased. FTIR spectroscopy revealed an increase in carbonyl groups produced by carbonylation reactions, from the hydroxyl groups or the cleavage of ether bonds. Both ESI–MS and GPC results show a negligible effect of the pyrolysis temperature on the molar weight distribution. This result differs with the increase in the molecular weight observed for organosolv lignin pyrolyzed in the screen heater and highlights the importance of secondary reactions on the outcome of fast pyrolysis reactors.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Effect of the Temperature on the Composition of Lignin Pyrolysis Products
Jiang, G., Nowakowski, D. J., & Bridgwater, A. V. (2010) · Energy & Fuels · doi:10.1021/ef100363c · Cited by 332
Garcia-Perez, M., Wang, S., Shen, J., Rhodes, M., Lee, W. J., & Li, C.-Z. (2008) · Energy & Fuels · doi:10.1021/ef7007634 · Cited by 235
Primary and secondary lignin pyrolysis reaction pathways
Jegers, H. E., & Klein, M. T. (1985) · Industrial & Engineering Chemistry Process Design and Development · doi:10.1021/i200028a030 · Cited by 182
Cited by
Hu, X., & Gholizadeh, M. (2019) · Journal of Energy Chemistry · doi:10.1016/j.jechem.2019.01.024 · Cited by 671
Cellulose, xylan and lignin interactions during pyrolysis of lignocellulosic biomass
Yu, J., Paterson, N., Blamey, J., & Millan, M. (2017) · Fuel · doi:10.1016/j.fuel.2016.11.057 · Cited by 452
Ojha, D. K., Viju, D., & Vinu, R. (2017) · Bioresource Technology · doi:10.1016/j.biortech.2017.05.084 · Cited by 81
Fast pyrolysis of lignins with different molecular weight: Experiments and modelling
Marathe, P. S., Westerhof, R. J. M., & Kersten, S. R. A. (2019) · Applied Energy · doi:10.1016/j.apenergy.2018.12.058 · Cited by 71
Self-citationIdentifying the primary reactions and products of fast pyrolysis of alkali lignin
Supriyanto, Usino, D. O., Ylitervo, P., Dou, J., Sipponen, M. H., & Richards, T. (2020) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2020.104917 · Cited by 54
“The decrease in yield with temperature was attributed to longer residence time [11] and secondary reactions in the vapour phase [20].”
Background
Metadata
- Authors
- Zhou, S., Garcia-Perez, M., Pecha, B., Kersten, S. R. A., McDonald, A. G., & Westerhof, R. J. M.
- Venue
- Energy & Fuels
- Publisher
- American Chemical Society (ACS)
- Published
- 2013-09-11
- Volume
- 27
- Issue
- 10
- Pages
- 5867-5877
- ISSN
- 0887-0624 (ISSN-L)
- 1520-5029
- OpenAlex
- W2161024649
- Cited by
- 89
- References
- 3
- FWCI
- 5.14
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.