The DOI matches its Crossref record; 7 of the 7 references it cites were found in a registry or an index.
Mass-Transfer Characterization of Metallic Foams as Supports for Structured Catalysts
Abstract
Open-celled metal foams have been characterized as supports for structured catalysts, considering their utilization in gas−solid catalytic processes with short contact times and high reaction rates, typically controlled by gas−solid diffusional mass transport. Examples of such processes are found in the field of environmental catalysis, including, e.g., catalytic combustion, selective catalytic reduction (SCR-DeNOx), and automotive exhaust gas after treatment. In this work, foams with different cell sizes were coated with a thin layer of palladium−alumina and tested in a 9-mm inner diameter tubular reactor by performing the catalytic oxidation of CO at empty tube velocities in the range of 0.8−2.6 m/s. The coated foams exhibited sufficient catalytic activity to achieve mass-transfer-limited operation in the temperature range of 300−450 °C. Under such conditions, mass-transfer coefficients were determined according to a simple one-dimensional model of the test reactor. Adopting the average diameter of the foam struts as the characteristic length, we obtained a dimensionless correlation for the estimation of mass-transfer coefficients, which correlates all the data: it closely resembles semitheoretical literature correlations for heat transfer in flow across banks of tubes at low Reynolds numbers. Pressure drop measurements across foam samples were also collected for air velocities in the range of 1−16 m/s. The performances of foams, packed beds of pellets, and honeycomb monoliths as catalyst supports were compared on the basis of a dimensionless merit index, which accounts for the tradeoff between pressure drop and mass-transfer properties. Foams are largely superior to packed beds, because of their high voidage, but perform slightly worse than honeycomb monoliths. On the other hand, foams can afford marked reductions of reactor volume and weight, with respect to honeycombs, in fast, diffusion-controlled processes where pressure drop is of minor concern.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Chemical Reactor Analysis and Design
Froment, G. F., Bischoff, K. B., & Wilde, J. D. (1979) · Digital Access to Libraries (Université catholique de Louvain (UCL), l'Université de Namur (UNamur) and the Université Saint-Louis (USL-B)) · Cited by 2,715
HAYHURST, A. N. (1997) · Food engineering series · doi:10.1007/978-1-4615-3864-6_3 · Cited by 999
On the effective thermal conductivity of a three-dimensionally structured fluid-saturated metal foam
Boomsma, K., & Poulikakos, D. (2001) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(00)00123-x · Cited by 831
Simulations of flow through open cell metal foams using an idealized periodic cell structure
Boomsma, K., Poulikakos, D., & Ventikos, Y. (2003) · International Journal of Heat and Fluid Flow · doi:10.1016/j.ijheatfluidflow.2003.08.002 · Cited by 322
Pressure drop prediction for flow through high porosity metallic foams
Du Plessis, P., Montillet, A., Comiti, J., & Legrand, J. (1994) · Chemical Engineering Science · doi:10.1016/0009-2509(94)00170-7 · Cited by 243
Antohe, B. V., Lage, J. L. C., Price, D. C., & Weber, R. M. (1996) · International Journal of Heat and Fluid Flow · doi:10.1016/s0142-727x(96)00085-9 · Cited by 68
Metal foam supported perovskite catalysts
Podyacheva, O. Y., Кетов, А. А., Ismagilov, Z. R., Ushakov, V. A., Bos, A. J. M., & Veringa, H. J. (1997) · Reaction Kinetics and Catalysis Letters · doi:10.1007/bf02475685 · Cited by 38
Cited by
Al-Ketan, O., Rowshan, R., & Abu Al-Rub, R. K. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2017.12.006 · Cited by 941
Nanoporous Copper Films by Additive-Controlled Electrodeposition: CO2 Reduction Catalysis
Hoang, T. T. H., Ma, S., Gold, J. I., Kenis, P. J. A., & Gewirth, A. A. (2017) · ACS Catalysis · doi:10.1021/acscatal.6b03613 · Cited by 296
A Review of Metal Foam and Metal Matrix Composites for Heat Exchangers and Heat Sinks
Han, X.-H., Wang, Q., Park, Y.-G., T’Joen, C., Sommers, A., & Jacobi, A. (2012) · Heat Transfer Engineering · doi:10.1080/01457632.2012.659613 · Cited by 279
Optimum structured adsorbents for gas separation processes
Rezaei, F., & Webley, P. (2009) · Chemical Engineering Science · doi:10.1016/j.ces.2009.08.029 · Cited by 210
Metadata
- Authors
- Giani, L., Groppi, G., & Tronconi, E.
- Venue
- Industrial & Engineering Chemistry Research
- Publisher
- American Chemical Society (ACS)
- Published
- 2005-02-09
- Volume
- 44
- Issue
- 14
- Pages
- 4993-5002
- ISSN
- 0888-5885 (ISSN-L)
- 1520-5045
- OpenAlex
- W2039085880
- Cited by
- 382
- References
- 7
- FWCI
- 9.11
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.