The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Stability of Supported Amine Adsorbents to SO2 and NOx in Postcombustion CO2 Capture. 1. Single-Component Adsorption
Abstract
Flue gases from coal-fired power plants typically contain not only CO 2 but other acid-gas impurities such as SO x and NO x that can dramatically influence the CO 2 capture efficiency. Whereas postcombustion CO 2 capture by aminosilica materials has been extensively studied over the past few years because of their high equilibrium CO 2 capacities, the performance of these materials under realistic conditions (in the presence of SO x, NO x, and O 2 ) remains relatively unexplored. In this study, the degree of irreversible binding of SO 2, NO, and NO 2 to four supported amine adsorbents is evaluated to assess the SO 2, NO, and NO 2 adsorption capacities of aminosilica sorbents and their effects on the CO 2 adsorption capacities. Adsorbents constructed using poly(ethyleneimine) and three different silane coupling agents (based on propyltrimethoxysilane linkers) with primary, secondary, and tertiary amines are evaluated. Under the experimental conditions used in this investigation, it is found that primary amines with high amine loadings displayed more affinity toward NO than their secondary and tertiary amine counterparts. However, overall, NO adsorption on the aminosilica adsorbents is low, and therefore, the CO 2 capacities of the adsorbent materials exposed to NO remained almost unchanged after the exposure. In contrast, all materials showed a very high nitrogen dioxide adsorption capacity upon exposure to NO 2 . As a result, all adsorbents treated with NO 2 exhibited a dramatic reduction in CO 2 capacity, which corresponds to the deactivation of amine groups due to the irreversible binding of NO 2 . In addition, our results indicate that SO 2 adsorbed significantly on supported amine adsorbents, resulting in a dramatic loss in CO 2 capacity during CO 2 capture from flue gas. With similar amine loadings, although secondary amines exhibited higher affinity to SO 2, their CO 2 capacity loss after exposure to SO 2 is lower than that of primary amines, indicating that these materials are more stable in the presence of SO 2, which implies that more SO 2 desorbs from secondary amines during the desorption step. These results suggest that for silica-supported amine materials to be useful in practical CO 2 capture applications, it is necessary to significantly reduce the SO 2 and NO 2 concentrations of the flue gas prior to the CO 2 capture process. On the other hand, the capture efficiency of these materials does not change significantly in the presence of NO. This suggests that such materials might be promising for postcombustion CO 2 capture from flue gas streams derived from natural gas combustion, as these streams typically contain reduced SO 2 concentrations but can still have significant NO x concentrations.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Carbon capture and storage: how green can black be
Haszeldine, R. S. (2009) · Science · doi:10.1126/science.1172246 · Cited by 2,021
Hedin, N., Andersson, L., Bergström, L., & Yan, J. (2013) · Applied Energy · doi:10.1016/j.apenergy.2012.11.034 · Cited by 424
Cited by
Amine-Based CO2 Capture Technology Development from the Beginning of 2013—A Review
Dutcher, B., Fan, M., & Russell, A. G. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/am507465f · Cited by 981
Porous materials for carbon dioxide separations
Siegelman, R. L., Kim, E. J., & Long, J. R. (2021) · Nature Materials · doi:10.1038/s41563-021-01054-8 · Cited by 722
Review on CO2 Capture Using Amine-Functionalized Materials
Hack, J., Maeda, N., & Meier, D. M. (2022) · ACS Omega · doi:10.1021/acsomega.2c03385 · Cited by 366
Abd, A. A., Naji, S. Z., Hashim, A. S., & Othman, M. R. (2020) · Journal of Environmental Chemical Engineering · doi:10.1016/j.jece.2020.104142 · Cited by 346
Comprehensive study of ultra-microporous nitrogen-doped activated carbon for CO2 capture
Sethia, G., & Sayari, A. (2015) · Carbon · doi:10.1016/j.carbon.2015.05.017 · Cited by 319
Metadata
- Authors
- Rezaei, F., & Jones, C. W.
- Venue
- Industrial & Engineering Chemistry Research
- Publisher
- American Chemical Society (ACS)
- Published
- 2013-08-13
- Volume
- 52
- Issue
- 34
- Pages
- 12192-12201
- ISSN
- 0888-5885 (ISSN-L)
- 1520-5045
- OpenAlex
- W2319500290
- Cited by
- 164
- References
- 2
- FWCI
- 11.07
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.