The DOI matches its Crossref record; 29 of the 29 references it cites were found in a registry or an index.
Parameters Affecting I–V Hysteresis of CH3NH3PbI3 Perovskite Solar Cells: Effects of Perovskite Crystal Size and Mesoporous TiO2 Layer
Open accessAbstract
Current-voltage (I-V) characteristics of CH3NH3PbI3 perovskite solar cells are studied using a time-dependent current response with stepwise sweeping of the bias voltage. Compared with the crystalline Si solar cell showing time-independent current at a given bias voltage, the perovskite solar cells exhibit time-dependent current response. The current increases with time and becomes steady at forward scan from short-circuit to open-circuit, whereas it is decayed and saturated with time at reverse scan from open-circuit to short-circuit. Time-dependent current response eventually leads to I-V hysteresis depending on the scan direction and the scan rate. Crystal size of CH3NH3PbI3 and the mesoporous TiO2 (mp-TiO2) film are found to influence I-V hysteresis, where the I-V hysteresis is alleviated as crystal size increases and in the presence of mp-TiO2. The capacitance observed at low frequency (0.1 to 1 Hz), associated with dipole polarization, tends to diminish as size of perovskite and mp-TiO2 layer thickness increases, which suggests that the origin of hysteresis correlates to the capacitive characteristic of CH3NH3PbI3 and the degree of hysteresis depends strongly on perovskite crystal size and mesoporous TiO2 layer.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Efficient Hybrid Solar Cells Based on Meso-Superstructured Organometal Halide Perovskites
Lee, M. M., Teuscher, J., Miyasaka, T., Murakami, T. N., & Snaith, H. J. (2012) · Science · doi:10.1126/science.1228604 · Cited by 10,687
Stranks, S. D., Eperon, G. E., Grancini, G., Menelaou, C., Alcocer, M. J. P., Leijtens, T., Herz, L. M., Petrozza, A., & Snaith, H. J. (2013) · Science · doi:10.1126/science.1243982 · Cited by 10,413
Sequential deposition as a route to high-performance perovskite-sensitized solar cells
Burschka, J., Pellet, N., Moon, S.-J., Humphry-Baker, R., Gao, P., Nazeeruddin, M. K., & Grätzel, M. (2013) · Nature · doi:10.1038/nature12340 · Cited by 9,547
Kim, H.-S., Lee, C.-R., Im, J.-H., Lee, K.-B., Moehl, T., Marchioro, A., Moon, S.-J., Humphry-Baker, R., Yum, J.-H., Moser, J. E., et al. (2012) · Scientific Reports · doi:10.1038/srep00591 · Cited by 8,092
Self-citationEfficient planar heterojunction perovskite solar cells by vapour deposition
Liu, M., Johnston, M. B., & Snaith, H. J. (2013) · Nature · doi:10.1038/nature12509 · Cited by 7,976
Long-Range Balanced Electron- and Hole-Transport Lengths in Organic-Inorganic CH 3 NH 3 PbI 3
Xing, G., Mathews, N., Sun, S., Lim, S. S., Lam, Y. M., Grätzel, M., Mhaisalkar, S., & Sum, T. C. (2013) · Science · doi:10.1126/science.1243167 · Cited by 6,909
Noh, J. H., Im, S. H., Heo, J. H., Mandal, T. N., & Seok, S. I. (2013) · Nano Letters · doi:10.1021/nl400349b · Cited by 4,829
Lead-free solid-state organic–inorganic halide perovskite solar cells
Hao, F., Stoumpos, C. C., Cao, D. H., Chang, R. P. H., & Kanatzidis, M. G. (2014) · Nature Photonics · doi:10.1038/nphoton.2014.82 · Cited by 3,026
Lead-free organic–inorganic tin halide perovskites for photovoltaic applications
Noel, N. K., Stranks, S. D., Abate, A., Wehrenfennig, C., Guarnera, S., Haghighirad, A.-A., Sadhanala, A., Eperon, G. E., Pathak, S. K., Johnston, M. B., et al. (2014) · Energy Environ. Sci. · doi:10.1039/c4ee01076k · Cited by 2,746
Anomalous Hysteresis in Perovskite Solar Cells
Snaith, H. J., Abate, A., Ball, J. M., Eperon, G. E., Leijtens, T., Noel, N. K., Stranks, S. D., Wang, J. T.-W., Wojciechowski, K., & Zhang, W. (2014) · The Journal of Physical Chemistry Letters · doi:10.1021/jz500113x · Cited by 2,465
Cited by
Intriguing Optoelectronic Properties of Metal Halide Perovskites
Manser, J. S., Christians, J. A., & Kamat, P. V. (2016) · Chemical Reviews · doi:10.1021/acs.chemrev.6b00136 · Cited by 2,020
Yuan, Y., & Huang, J. (2016) · Accounts of Chemical Research · doi:10.1021/acs.accounts.5b00420 · Cited by 1,865
Defect migration in methylammonium lead iodide and its role in perovskite solar cell operation
Azpiroz, J. M., Mosconi, E., Bisquert, J., & De Angelis, F. (2015) · Energy & Environmental Science · doi:10.1039/c5ee01265a · Cited by 1,644
Perovskite Solar Cells: From Materials to Devices
Jung, H. S., & Park, N. (2015) · Small · doi:10.1002/smll.201402767 · Cited by 1,587
Self-citationTress, W., Marinova, N., Moehl, T., Zakeeruddin, S. M., Nazeeruddin, M. K., & Grätzel, M. (2015) · Energy & Environmental Science · doi:10.1039/c4ee03664f · Cited by 1,381
Reversible Hydration of CH3NH3PbI3 in Films, Single Crystals, and Solar Cells
Leguy, A. M. A., Hu, Y., Campoy-Quiles, M., Alonso, M. I., Weber, O. J., Azarhoosh, P., van Schilfgaarde, M., Weller, M. T., Bein, T., Nelson, J., et al. (2015) · Chemistry of Materials · doi:10.1021/acs.chemmater.5b00660 · Cited by 1,366
A Review of Perovskites Solar Cell Stability
Wang, R., Mujahid, M., Duan, Y., Wang, Z., Xue, J., & Yang, Y. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201808843 · Cited by 1,310
Stability of Metal Halide Perovskite Solar Cells
Leijtens, T., Eperon, G. E., Noel, N. K., Habisreutinger, S. N., Petrozza, A., & Snaith, H. J. (2015) · Advanced Energy Materials · doi:10.1002/aenm.201500963 · Cited by 1,308
Under the spotlight: The organic–inorganic hybrid halide perovskite for optoelectronic applications
Chen, Q., De Marco, N., Yang, Y. (., Song, T.-B., Chen, C.-C., Zhao, H., Hong, Z., Zhou, H., & Yang, Y. (2015) · Nano Today · doi:10.1016/j.nantod.2015.04.009 · Cited by 1,154
Lewis Acid–Base Adduct Approach for High Efficiency Perovskite Solar Cells
Lee, J.-W., Kim, H.-S., & Park, N.-G. (2016) · Accounts of Chemical Research · doi:10.1021/acs.accounts.5b00440 · Cited by 1,067
Self-citationToward Large Scale Roll‐to‐Roll Production of Fully Printed Perovskite Solar Cells
Hwang, K., Jung, Y., Heo, Y., Scholes, F. H., Watkins, S. E., Subbiah, J., Jones, D. J., Kim, D., & Vak, D. (2015) · Advanced Materials · doi:10.1002/adma.201404598 · Cited by 930
Unreacted PbI2 as a Double-Edged Sword for Enhancing the Performance of Perovskite Solar Cells
Jacobsson, T. J., Correa-Baena, J.-P., Halvani Anaraki, E., Philippe, B., Stranks, S. D., Bouduban, M. E. F., Tress, W., Schenk, K., Teuscher, J., Moser, J.-E., et al. (2016) · Journal of the American Chemical Society · doi:10.1021/jacs.6b06320 · Cited by 901
Universal Approach toward Hysteresis-Free Perovskite Solar Cell via Defect Engineering
Son, D.-Y., Kim, S.-G., Seo, J.-Y., Lee, S.-H., Shin, H., Lee, D., & Park, N.-G. (2018) · Journal of the American Chemical Society · doi:10.1021/jacs.7b10430 · Cited by 891
Self-citationEvidence for ion migration in hybrid perovskite solar cells with minimal hysteresis
Calado, P., Telford, A. M., Bryant, D., Li, X., Nelson, J., O’Regan, B. C., & Barnes, P. R. F. (2016) · Nature Communications · doi:10.1038/ncomms13831 · Cited by 845
Tress, W., Yavari, M., Domanski, K., Yadav, P., Niesen, B., Correa Baena, J. P., Hagfeldt, A., & Graetzel, M. (2018) · Energy & Environmental Science · doi:10.1039/c7ee02415k · Cited by 843
Chueh, C.-C., Li, C.-Z., & Jen, A. K.-Y. (2015) · Energy & Environmental Science · doi:10.1039/c4ee03824j · Cited by 799
In situ observation of heat-induced degradation of perovskite solar cells
Divitini, G., Cacovich, S., Matteocci, F., Cinà, L., Di Carlo, A., & Ducati, C. (2016) · Nature Energy · doi:10.1038/nenergy.2015.12 · Cited by 782
Highly stable, phase pure Cs2AgBiBr6 double perovskite thin films for optoelectronic applications
Greul, E., Petrus, M. L., Binek, A., Docampo, P., & Bein, T. (2017) · Journal of Materials Chemistry A · doi:10.1039/c7ta06816f · Cited by 772
Causes and Solutions of Recombination in Perovskite Solar Cells
Chen, J., & Park, N. (2019) · Advanced Materials · doi:10.1002/adma.201803019 · Cited by 733
Self-citationModeling Anomalous Hysteresis in Perovskite Solar Cells
van Reenen, S., Kemerink, M., & Snaith, H. J. (2015) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.5b01645 · Cited by 687
Stable high efficiency two-dimensional perovskite solar cells via cesium doping
Zhang, X., Ren, X., Liu, B., Munir, R., Zhu, X., Yang, D., Li, J., Liu, Y., Smilgies, D.-M., Li, R., et al. (2017) · Energy & Environmental Science · doi:10.1039/c7ee01145h · Cited by 678
Understanding of perovskite crystal growth and film formation in scalable deposition processes
Liu, C., Cheng, Y.-B., & Ge, Z. (2020) · Chemical Society Reviews · doi:10.1039/c9cs00711c · Cited by 675
The dynamics of methylammonium ions in hybrid organic–inorganic perovskite solar cells
Leguy, A. M. A., Frost, J. M., McMahon, A. P., Sakai, V. G., Kockelmann, W., Law, C., Li, X., Foglia, F., Walsh, A., O’Regan, B. C., et al. (2015) · Nature Communications · doi:10.1038/ncomms8124 · Cited by 647
Ke, W., Xiao, C., Wang, C., Saparov, B., Duan, H., Zhao, D., Xiao, Z., Schulz, P., Harvey, S. P., Liao, W., et al. (2016) · Advanced Materials · doi:10.1002/adma.201600594 · Cited by 579
Recent progress in electron transport layers for efficient perovskite solar cells
Yang, G., Tao, H., Qin, P., Ke, W., & Fang, G. (2016) · Journal of Materials Chemistry A · doi:10.1039/c5ta09011c · Cited by 579
Iodine Migration and its Effect on Hysteresis in Perovskite Solar Cells
Li, C., Tscheuschner, S., Paulus, F., Hopkinson, P. E., Kießling, J., Köhler, A., Vaynzof, Y., & Huettner, S. (2016) · Advanced Materials · doi:10.1002/adma.201503832 · Cited by 549
Functionalization of perovskite thin films with moisture-tolerant molecules
Yang, S., Wang, Y., Liu, P., Cheng, Y.-B., Zhao, H. J., & Yang, H. G. (2016) · Nature Energy · doi:10.1038/nenergy.2015.16 · Cited by 521
Materials and Methods for Interface Engineering toward Stable and Efficient Perovskite Solar Cells
Chen, J., & Park, N.-G. (2020) · ACS Energy Letters · doi:10.1021/acsenergylett.0c01240 · Cited by 521
Self-citationBu, T., Liu, X., Zhou, Y., Yi, J., Huang, X., Luo, L., Xiao, J., Ku, Z., Peng, Y., Huang, F., et al. (2017) · Energy & Environmental Science · doi:10.1039/c7ee02634j · Cited by 516
Almora, O., Zarazua, I., Mas-Marza, E., Mora-Sero, I., Bisquert, J., & Garcia-Belmonte, G. (2015) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.5b00480 · Cited by 503
Kang, D., & Park, N. (2019) · Advanced Materials · doi:10.1002/adma.201805214 · Cited by 498
Self-citationRecent advances in perovskite solar cells: efficiency, stability and lead-free perovskite
Yang, S., Fu, W., Zhang, Z., Chen, H., & Li, C.-Z. (2017) · Journal of Materials Chemistry A · doi:10.1039/c7ta00366h · Cited by 486
Frontiers, opportunities, and challenges in perovskite solar cells: A critical review
Ansari, M. I. H., Qurashi, A., & Nazeeruddin, M. K. (2018) · Journal of Photochemistry and Photobiology C: Photochemistry Reviews · doi:10.1016/j.jphotochemrev.2017.11.002 · Cited by 485
Control of I–V Hysteresis in CH3NH3PbI3 Perovskite Solar Cell
Kim, H.-S., Jang, I.-H., Ahn, N., Choi, M., Guerrero, A., Bisquert, J., & Park, N.-G. (2015) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.5b02273 · Cited by 478
Self-citationYun, J. S., Seidel, J., Kim, J., Soufiani, A. M., Huang, S., Lau, J., Jeon, N. J., Seok, S. I., Green, M. A., & Ho‐Baillie, A. (2016) · Advanced Energy Materials · doi:10.1002/aenm.201600330 · Cited by 472
A Bifunctional Lewis Base Additive for Microscopic Homogeneity in Perovskite Solar Cells
Lee, J.-W., Bae, S.-H., Hsieh, Y.-T., De Marco, N., Wang, M., Sun, P., & Yang, Y. (2017) · Chem · doi:10.1016/j.chempr.2017.05.020 · Cited by 459
Hawash, Z., Ono, L. K., & Qi, Y. (2018) · Advanced Materials Interfaces · doi:10.1002/admi.201700623 · Cited by 455
Hole Selective NiO Contact for Efficient Perovskite Solar Cells with Carbon Electrode
Xu, X., Liu, Z., Zuo, Z., Zhang, M., Zhao, Z., Shen, Y., Zhou, H., Chen, Q., Yang, Y., & Wang, M. (2015) · Nano Letters · doi:10.1021/nl504701y · Cited by 445
Lyu, M., Yun, J., Chen, P., Hao, M., & Wang, L. (2017) · Advanced Energy Materials · doi:10.1002/aenm.201602512 · Cited by 432
Doping of TiO2for sensitized solar cells
Roose, B., Pathak, S., & Steiner, U. (2015) · Chemical Society Reviews · doi:10.1039/c5cs00352k · Cited by 427
Device stability of perovskite solar cells – A review
Asghar, M. I., Zhang, J., Wang, H., & Lund, P. D. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.04.003 · Cited by 423
Impact of Capacitive Effect and Ion Migration on the Hysteretic Behavior of Perovskite Solar Cells
Chen, B., Yang, M., Zheng, X., Wu, C., Li, W., Yan, Y., Bisquert, J., Garcia-Belmonte, G., Zhu, K., & Priya, S. (2015) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.5b02229 · Cited by 391
Ultra-thin high efficiency semitransparent perovskite solar cells
Della Gaspera, E., Peng, Y., Hou, Q., Spiccia, L., Bach, U., Jasieniak, J. J., & Cheng, Y.-B. (2015) · Nano Energy · doi:10.1016/j.nanoen.2015.02.028 · Cited by 390
Razza, S., Di Giacomo, F., Matteocci, F., Cinà, L., Palma, A. L., Casaluci, S., Cameron, P., D'Epifanio, A., Licoccia, S., Reale, A., et al. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.12.008 · Cited by 384
Hysteresis Analysis Based on the Ferroelectric Effect in Hybrid Perovskite Solar Cells
Wei, J., Zhao, Y., Li, H., Li, G., Pan, J., Xu, D., Zhao, Q., & Yu, D. (2014) · The Journal of Physical Chemistry Letters · doi:10.1021/jz502111u · Cited by 379
Interfaces in Perovskite Solar Cells
Fakharuddin, A., Schmidt‐Mende, L., Garcia‐Belmonte, G., Jose, R., & Mora‐Sero, I. (2017) · Advanced Energy Materials · doi:10.1002/aenm.201700623 · Cited by 349
Material and Device Stability in Perovskite Solar Cells
Kim, H., Seo, J., & Park, N. (2016) · ChemSusChem · doi:10.1002/cssc.201600915 · Cited by 346
Self-citationYang, M., Zhou, Y., Zeng, Y., Jiang, C., Padture, N. P., & Zhu, K. (2015) · Advanced Materials · doi:10.1002/adma.201502586 · Cited by 344
From Ultrafast to Ultraslow: Charge-Carrier Dynamics of Perovskite Solar Cells
Shi, J., Li, Y., Li, Y., Li, D., Luo, Y., Wu, H., & Meng, Q. (2018) · Joule · doi:10.1016/j.joule.2018.04.010 · Cited by 341
Encapsulation for long-term stability enhancement of perovskite solar cells
Matteocci, F., Cinà, L., Lamanna, E., Cacovich, S., Divitini, G., Midgley, P. A., Ducati, C., & Di Carlo, A. (2016) · Nano Energy · doi:10.1016/j.nanoen.2016.09.041 · Cited by 340
Unbroken Perovskite: Interplay of Morphology, Electro‐optical Properties, and Ionic Movement
Correa‐Baena, J., Anaya, M., Lozano, G., Tress, W., Domanski, K., Saliba, M., Matsui, T., Jacobsson, T. J., Calvo, M. E., Abate, A., et al. (2016) · Advanced Materials · doi:10.1002/adma.201600624 · Cited by 301
Chen, J., Seo, J., & Park, N. (2018) · Advanced Energy Materials · doi:10.1002/aenm.201702714 · Cited by 299
Self-citationPhase Transition Control for High Performance Ruddlesden–Popper Perovskite Solar Cells
Zhang, X., Munir, R., Xu, Z., Liu, Y., Tsai, H., Nie, W., Li, J., Niu, T., Smilgies, D., Kanatzidis, M. G., et al. (2018) · Advanced Materials · doi:10.1002/adma.201707166 · Cited by 294
Sepalage, G. A., Meyer, S., Pascoe, A., Scully, A. D., Huang, F., Bach, U., Cheng, Y., & Spiccia, L. (2015) · Advanced Functional Materials · doi:10.1002/adfm.201502541 · Cited by 290
Shi, J., Gao, Y., Gao, X., Zhang, Y., Zhang, J., Jing, X., & Shao, M. (2019) · Advanced Materials · doi:10.1002/adma.201901673 · Cited by 286
High-efficiency humidity-stable planar perovskite solar cells based on atomic layer architecture
Koushik, D., Verhees, W. J. H., Kuang, Y., Veenstra, S., Zhang, D., Verheijen, M. A., Creatore, M., & Schropp, R. E. I. (2017) · Energy & Environmental Science · doi:10.1039/c6ee02687g · Cited by 285
Encapsulation for improving the lifetime of flexible perovskite solar cells
Weerasinghe, H. C., Dkhissi, Y., Scully, A. D., Caruso, R. A., & Cheng, Y.-B. (2015) · Nano Energy · doi:10.1016/j.nanoen.2015.10.006 · Cited by 284
Pinhole-free perovskite films for efficient solar modules
Qiu, W., Merckx, T., Jaysankar, M., Masse de la Huerta, C., Rakocevic, L., Zhang, W., Paetzold, U. W., Gehlhaar, R., Froyen, L., Poortmans, J., et al. (2016) · Energy & Environmental Science · doi:10.1039/c5ee03703d · Cited by 284
Metal Oxide Charge Transport Layers for Efficient and Stable Perovskite Solar Cells
Shin, S. S., Lee, S. J., & Seok, S. I. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201900455 · Cited by 283
Research Direction toward Scalable, Stable, and High Efficiency Perovskite Solar Cells
Park, N. (2020) · Advanced Energy Materials · doi:10.1002/aenm.201903106 · Cited by 268
Self-citationO’Regan, B. C., Barnes, P. R. F., Li, X., Law, C., Palomares, E., & Marin-Beloqui, J. M. (2015) · Journal of the American Chemical Society · doi:10.1021/jacs.5b00761 · Cited by 264
Najafi, L., Taheri, B., Martín-García, B., Bellani, S., Di Girolamo, D., Agresti, A., Oropesa-Nuñez, R., Pescetelli, S., Vesce, L., Calabrò, E., et al. (2018) · ACS Nano · doi:10.1021/acsnano.8b05514 · Cited by 264
Pearson, A. J., Eperon, G. E., Hopkinson, P. E., Habisreutinger, S. N., Wang, J. T., Snaith, H. J., & Greenham, N. C. (2016) · Advanced Energy Materials · doi:10.1002/aenm.201600014 · Cited by 256
Wu, Z., Liu, Z., Hu, Z., Hawash, Z., Qiu, L., Jiang, Y., Ono, L. K., & Qi, Y. (2019) · Advanced Materials · doi:10.1002/adma.201804284 · Cited by 256
Mahmood, K., Swain, B. S., & Amassian, A. (2015) · Advanced Energy Materials · doi:10.1002/aenm.201500568 · Cited by 252
Metadata
- Authors
- Kim, H.-S., & Park, N.-G.
- Venue
- The Journal of Physical Chemistry Letters
- Publisher
- American Chemical Society (ACS)
- Published
- 2014-08-17
- Volume
- 5
- Issue
- 17
- Pages
- 2927-2934
- ISSN
- 1948-7185 (ISSN-L)
- OpenAlex
- W2323653673
- Cited by
- 1,065
- References
- 29
- FWCI
- 78.71
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.