Student or educator? Sign up with your school email and get 6 months of Pro free.
Cited by 178

The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.

Methanol Electrooxidation over Pt/C Fuel Cell Catalysts: Dependence of Product Yields on Catalyst Loading

Jusys, Z., Kaiser, J., Behm, R. J.·2003·Langmuir

Abstract

We have investigated the influence of the catalyst loading (7−35 μg Pt ·cm - 2 ) on methanol oxidation product yields over Vulcan XC72 supported Pt catalyst by differential electrochemical mass spectrometry (DEMS), both under potentiodynamic and potentiostatic (0.6 V RHE ) conditions. Experiments were performed at room temperature and under continuous flow conditions (0.1 M CH 3 OH in 0.5 M H 2 SO 4 solution). Absolute calibration of the DEMS signal allowed determination of current efficiencies for the final reaction product CO 2 and for the reaction intermediates formic acid and formaldehyde. These could be converted into turnover frequencies (TOFs) on the basis of the physical (transmission electron microscopy) and electrochemical (CO stripping, H UPD ) determination of the absolute particle surface area. The good agreement between these values indicates 100% utilization of the catalyst. The electrochemical efficiencies, product distribution, and the turnover frequencies of partial reactions (methanol oxidation to formaldehyde, formic acid, and CO 2 ), during the methanol oxidation reaction (MOR) show a pronounced dependence on the catalyst loading. With increasing Pt loading the current efficiency for methanol oxidation to formaldehyde decays significantly (40% to almost 0%), while that for complete oxidation to CO 2 increases from 50 to 80%. The variation in current efficiency for methanol oxidation to formic acid is small (ca. 10%). The product distribution varies accordingly; the absolute numbers, however, are different: Low (5−20%) formic acid yields are accompanied by a decaying formaldehyde yield (60% to zero) and increasing CO 2 yield (30−80%) with increasing catalyst loading. The total TOF values calculated from the values for the individual reaction pathways and products are significantly higher than the Faradaic TOF numbers at low catalyst loadings, while at high loadings, where complete oxidation of methanol to CO 2 is preferred, they agree satisfactorily. The pronounced variations in product distribution/TOF values are attributed to increasing readsorption and subsequent complete oxidation of desorbed reaction intermediates (formaldehyde and formic acid) at higher catalyst loadings, while at low loadings or, even more pronounced, on smooth electrodes these intermediates are more likely to survive. This has to be considered for predictions of MOR characteristics under fuel cell conditions on the basis of studies on smooth electrodes.

Overview

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1021/la020932b

Cites

1 of 1 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 1 references

Cited by

Metadata

Authors
Jusys, Z., Kaiser, J., & Behm, R. J.
Venue
Langmuir
Published
2003-07-25
Volume
19
Issue
17
Pages
6759-6769
ISSN
  • 0743-7463 (ISSN-L)
  • 1520-5827
OpenAlex
W2030951199
Cited by
178
References
1
FWCI
9.56
Type
journal article
Language
en
Open access
closed

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.