The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Determination of the Receding Contact Angle of Sessile Drops on Polymer Surfaces by Evaporation
Abstract
The receding contact angles of water drops on PMMA and PET surfaces were determined by using video microscopy to follow the time-dependent evaporation of sessile drops. Depending on the initial drop size, receding angles of θ r = 54−64° for PMMA and θ r = 64−66° for PET were found with an average hysteresis of 23.5 ± 1.5 and 19.5 ± 1.5°, respectively. Advancing and receding angles, θ a and θ r, were also determined by the needle-syringe and the inclined plane methods for comparison. The discrepancies from the mean of the maximum and minimum contact angle results of both the needle-syringe and the inclined plane methods were larger than expected for all the polymer surfaces. A general trend was seen with samples giving a larger hysteresis also producing a larger discrepancy for all the samples. The major cause of this discrepancy is the variation of the rate of liquid introduction and withdrawal with the syringe in the needle-syringe method and the drop size effect in the inclined plane method. In this respect the drop evaporation method allows a rate of liquid withdrawal which minimizes (or standardizes) the linear rate of retreat effect on receding contact angle measurement. The literature values are also given for comparison. A discrepancy of 11−15% from the mean for θ a and 27−32% for θ r is reported in the literature for these polymers. This is approximately five times more than the previously claimed 2−3% deviation from the mean for θ a on the same clean homopolymer samples.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Wettability of porous surfaces
Cassie, A. B. D., & Baxter, S. (1944) · Transactions of the Faraday Society · doi:10.1039/tf9444000546 · Cited by 13,807
RESISTANCE OF SOLID SURFACES TO WETTING BY WATER
Wenzel, R. N. (1936) · Industrial & Engineering Chemistry · doi:10.1021/ie50320a024 · Cited by 13,316
Cited by
Contact angle hysteresis: a review of fundamentals and applications
Eral, H. B., ’t Mannetje, D. J. C. M., & Oh, J. M. (2013) · Colloid and Polymer Science · doi:10.1007/s00396-012-2796-6 · Cited by 720
Evaporation of pure liquid sessile and spherical suspended drops: A review
Erbil, H. Y. (2012) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2011.12.006 · Cited by 612
Self-citationErbil, H. Y. (2014) · Surface Science Reports · doi:10.1016/j.surfrep.2014.09.001 · Cited by 332
Self-citationSurface free energy of a solid from contact angle hysteresis
Chibowski, E. (2003) · Advances in Colloid and Interface Science · doi:10.1016/s0001-8686(02)00093-3 · Cited by 315
Droplet and bubble wetting behaviors: The roles of surface wettability and roughness
Xiao, Y., Zheng, J., He, Y., & Wang, L. (2022) · Colloids and Surfaces A: Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2022.130008 · Cited by 90
Metadata
- Authors
- Erbil, H. Y., McHale, G., Rowan, S. M., & Newton, M. I.
- Venue
- Langmuir
- Publisher
- American Chemical Society (ACS)
- Published
- 1999-09-24
- Volume
- 15
- Issue
- 21
- Pages
- 7378-7385
- ISSN
- 0743-7463 (ISSN-L)
- 1520-5827
- OpenAlex
- W2001120038
- Cited by
- 214
- References
- 2
- FWCI
- 1.93
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Determination of the Receding Contact Angle of Sessile Drops on Polymer Surfaces by Evaporation. https://app.cochat.ai/papers/10.1021/la9900831
- The paper
- Erbil, H. Y., McHale, G., Rowan, S. M., & Newton, M. I. (1999). Determination of the Receding Contact Angle of Sessile Drops on Polymer Surfaces by Evaporation. Langmuir. https://doi.org/10.1021/la9900831
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.