CoChat
Sign Up
Cited by 183earthquake and tectonic studiesGeological and Tectonic Studies in Latin AmericaGeological and Geophysical Studies

The DOI matches its Crossref record; 31 of the 31 references it cites were found in a registry or an index.

Brittle frictional mountain building: 1. Deformation and mechanical energy budget

Dahlen, F. A., Barr, Terence D.·1989·Journal of Geophysical Research: Solid Earth
DOI 10.1029/jb094ib04p03906
Open this paper in CoChat — free account

Abstract

An active fold‐and‐thrust belt is analogous to a wedge of soil or snow that forms in front of a moving bulldozer; such wedges exhibit a critical taper and a regional state of stress that is everywhere on the verge of Coulomb failure. The width of such a critically tapered fold‐and‐thrust belt does not depend on its brittle strength or frictional properties but rather on the accretionary influx rate of fresh material at its toe and on the rate of erosion; a steady state fold‐and‐thrust belt is one in which the accretionary influx is balanced by the erosive efflux. Rocks are accreted at the toe and then horizontally shortened as they are transported toward the rear; those that enter lower in the accreted section are more deeply buried before being uplifted by erosion. Mass balance and isotropy constrain the kinematics of this large‐scale deformation, enabling us to infer the trajectories, residence times, and stress‐strain histories of rocks incorporated into eroding fold‐and‐thrust belts. A typical rock resides in the steady state Taiwan wedge for 2–3 m.y. before it is uplifted and eroded; during its motion through the wedge, it experiences strain rates in the range 10−13 to 10−14 s−1. The mechanical energy budget of brittle frictional mountain building is described by the equation , where is the rate of work performed on the base and front of the fold‐and‐thrust belt by the subducting plate, is the rate at which energy is dissipated against friction on the decollement fault, is the rate at which energy is dissipated by internal frictional processes within the deforming brittle wedge, and is the rate of work performed against gravitational body forces in a reference frame attached to the overriding plate. The total mechanical power being supplied by the subducting Eurasian plate to the active fold‐and‐thrust belt in Taiwan is slightly over 3 GW. Approximately 60% of this work of steady state mountain building is being dissipated against friction on the decollement fault, and about another 25% is being dissipated against internal friction; this leaves only 15% or roughly half a gigawatt available to do useful work against gravity. In general, fold‐and‐thrust belts with moderate pore fluid pressures are dominated by work done against friction on the decollement fault; however, those with nearly lithostatic pore fluid pressures may be dominated by work done against gravity. Internal frictional dissipation is always less than basal frictional dissipation, as it is in Taiwan. An alternative and equivalent description of the mechanical energy balance of a steady state fold‐and‐thrust belt is provided by the equation . In this version the quantity on the left, , is the rate at which work is performed on the back of the wedge by the overriding plate and is the rate of work performed against gravity in a reference frame attached to the subducting plate. The latter quantity is always positive for any critically tapered fold‐and‐thrust belt whose decollement fault dips toward its rear, in contradiction to the central premise of the gravity spreading theory of fold‐and‐thrust tectonics.

Overview

Integrity signals

Registry

Crossref · 10.1029/jb094ib04p03906

Cites

31 of 31 references verified0 citation errors · 0 not checkable

Statistics

Recomputing p-values needs the paper’s full text.

Verification

Claims the paper makes

This paper’s full text isn’t openly available, so its claims and self-check weren’t run. The registry and citation checks still apply.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Citations

Cites

Flagged first, then by citations

Research works printed but not linked: 6

  1. Boyer S. E., 1982, Thrust systems, Am. Assoc. Pet. Geol. Bull., 66, 1196
  2. Chi W. R., 1981, Stratigraphic record of plate interactions in the Coastal Range of eastern Taiwan, Mem. Geol. Soc. China, 4, 491
  3. 1986, Europa Yearbook1, The, A World Survey
  4. Peng T. H., 1977, Tectonic uplift rates of the Taiwan island since the early Holocene, Mem. Geol. Soc. China, 2, 57
  5. Rice J. R., 1980, Physics of the Earth's Interior, 555
  6. 10.2475/ajs.265.7.545 · DOI

Cited by

Sorted by citations

See all 183

Related

See all

Metadata

Authors
Dahlen, F. A., & Barr, T. D.
Venue
Journal of Geophysical Research: Solid Earth
Publisher
American Geophysical Union (AGU)
Published
1989-04-10
Volume
94
Issue
B4
Pages
3906-3922
ISSN
0148-0227 (ISSN-L)
DOI
10.1029/jb094ib04p03906
OpenAlex
W2074494339
Cited by
183
References
31
Citations by year
2025: 1 · 2024: 1 · 2023: 1 · 2022: 5 · 2021: 3 · 2020: 3 · 2019: 8 · 2018: 15 · 2017: 3 · 2016: 3 · 2015: 2 · 2014: 7 · 2013: 4 · 2012: 1
FWCI
6.17
Type
journal article
Language
en
Open access
closed
Licence
onlinelibrary.wiley.com/termsAndConditions#vor (vor, 8564 d)
Locations
Journal of Geophysical Research Atmospheres (publishedVersion)
Topics
  • Physical Sciences › Earth and Planetary Sciences › Geophysics › earthquake and tectonic studies
  • Physical Sciences › Earth and Planetary Sciences › Geophysics › Geological and Tectonic Studies in Latin America
  • Physical Sciences › Earth and Planetary Sciences › Geology › Geological and Geophysical Studies
Keywords
fold and thrust belt, critical taper, accretionary prism, subduction, Coulomb failure, strain rate, pore pressure, mechanical power, mass balance, deformation kinematics

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review