Student or educator? Sign up with your school email and get 6 months of Pro free.
Cited by 313

The DOI matches its Crossref record.

Micromechanics of the brittle to plastic transition in Carrara marble

Fredrich, Joanne T., Evans, Brian, Wong, Teng‐Fong·1989·Journal of Geophysical Research: Solid Earth

Abstract

Samples of Carrara marble were deformed at room temperature to varying strains at confining pressures spanning the range in mechanical behavior from brittle to plastic. Volumetric strain was measured during the experiments, and the stress‐induced microstructure was characterized quantitatively using optical and transmission electron microscopy. The range of confining pressure over which transitional (or semibrittle) deformation occurs is 30–300 MPa. The macroscopic initial yield stress is constant for confining pressures greater than 85 MPa, whereas the differential stress at the onset of dilatancy increases with pressure up to 300 MPa. The dilatancy coefficient decreases rapidly with increasing pressure up to 100 MPa, and then asymptotically approaches zero for pressures up to 300 MPa. The work hardening coefficient increases with pressure up to 450 MPa; the pressure sensitivity is greatest for pressures up to 100 MPa. Active deformation mechanisms include microcracking, twinning, and dislocation glide. Transmission electron microscopy observations indicate that dislocation glide occurs, at least on a local scale, in samples deformed in the semibrittle field at pressures as low as 50 MPa and applied differential stress well below the critical resolved shear stress for glide on the easiest slip system. Cracks and voids frequently nucleate at sites of stress concentration at twin boundaries, at twin terminations, and at the intersection of twin lamallae. Geometries suggestive of crack tip shielding by dislocations are also observed. Stereological measurements indicate that at constant strain in the semibrittle field, the stress‐induced crack density and anisotropy decrease with increasing pressure. Crack density and anisotropy in samples deformed to strains of 3–5% in the semibrittle field at pressures up to 120 MPa are comparable to those in the prefailure brittle sample, although an analysis of the energetics of deformation suggests that the ratio of brittle energy dissipation to total energy dissipation is at least 60% lower. We also detect a qualitative difference in the characteristic length of the cracks in the brittle and semibrittle fields. The mean dislocation density at constant differential stress increases significantly for samples deformed at pressures of 230 MPa and greater. Our results suggest that although semibrittle flow occurs over a wide range of pressure, the most marked changes in strain partitioning, and hence the style of deformation occur over a small range in pressure.

Overview

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1029/jb094ib04p04129

Cites

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cited by

See all 313

Metadata

Authors
Fredrich, J. T., Evans, B., & Wong, T.
Venue
Journal of Geophysical Research: Solid Earth
Published
1989-04-10
Volume
94
Issue
B4
Pages
4129-4145
ISSN
0148-0227 (ISSN-L)
OpenAlex
W2021622140
Cited by
313
References
0
FWCI
14.19
Type
journal article
Language
en
Open access
closed

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Micromechanics of the brittle to plastic transition in Carrara marble. https://app.cochat.ai/papers/10.1029/jb094ib04p04129
The paper
Fredrich, J. T., Evans, B., & Wong, T. (1989). Micromechanics of the brittle to plastic transition in Carrara marble. Journal of Geophysical Research: Solid Earth. https://doi.org/10.1029/jb094ib04p04129

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.