CoChat

Ambipolar solution-processed hybrid perovskite phototransistors

Open access
Li, Feng, Ma, Chun, Wang, Hong, Hu, Weijin, Yu, Weili, Sheikh, Arif D., Wu, Tom · 2015 · Nature Communications

The DOI matches its Crossref record; 87 of the 87 references it cites were found in a registry or an index.

Abstract

Organolead halide perovskites have attracted substantial attention because of their excellent physical properties, which enable them to serve as the active material in emerging hybrid solid-state solar cells. Here we investigate the phototransistors based on hybrid perovskite films and provide direct evidence for their superior carrier transport property with ambipolar characteristics. The field-effect mobilities for triiodide perovskites at room temperature are measured as 0.18 (0.17) cm 2 V −1 s −1 for holes (electrons), which increase to 1.24 (1.01) cm 2 V −1 s −1 for mixed-halide perovskites. The photoresponsivity of our hybrid perovskite devices reaches 320 A W −1 , which is among the largest values reported for phototransistors. Importantly, the phototransistors exhibit an ultrafast photoresponse speed of less than 10 μs. The solution-based process and excellent device performance strongly underscore hybrid perovskites as promising material candidates for photoelectronic applications.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1038/ncomms9238

Cites

87 of 87 references verified0 citation errors · 0 not checkable

Statistics

Figures

Figure 1 Hybrid perovskite phototransistors. (a) Schematic of the phototransistor with a channel of hybrid perovskite CH3NH3PbI3. (b) Ultraviolet–visible absorption of the 100-nm CH3NH3PbI3 film. The inset shows a direct bandgap of ∼1.53 eV. (c) X-ray diffraction spectrum of the CH3NH3PbI3 film. (d) Top-view SEM image of the perovskite film. Scale bar, 0.5 μm. (e) Tapping-mode AFM height image of the perovskite film. Scale bar, 1.0 μm. Inset: the corresponding three-dimensional topographic image.
Figure 1 Hybrid perovskite phototransistors. (a) Schematic of the phototransistor with a channel of hybrid perovskite CH3NH3PbI3. (b) Ultraviolet–visible absorption of the 100-nm CH3NH3PbI3 film. The inset shows a direct bandgap of ∼1.53 eV. (c) X-ray diffraction spectrum of the CH3NH3PbI3 film. (d) Top-view SEM image of the perovskite film. Scale bar, 0.5 μm. (e) Tapping-mode AFM height image of the perovskite film. Scale bar, 1.0 μm. Inset: the corresponding three-dimensional topographic image.CC BY · PubMed Central
Figure 2 Ambipolar characteristics of the hybrid perovskite phototransistors. (a) Transfer characteristics of a perovskite-based phototransistor in the dark (black and red symbols) and under light illumination (blue and magenta symbols). (b,c) Representation of the transfer characteristics of p-channel and n-channel behaviours, respectively, under light illumination. (d,e) Respective output properties of the device under light condition. (f) Output curves of the phototransistor in the dark condition. Solid and dashed curves were measured during forward and backward sweepings, respectively.
Figure 2 Ambipolar characteristics of the hybrid perovskite phototransistors. (a) Transfer characteristics of a perovskite-based phototransistor in the dark (black and red symbols) and under light illumination (blue and magenta symbols). (b,c) Representation of the transfer characteristics of p-channel and n-channel behaviours, respectively, under light illumination. (d,e) Respective output properties of the device under light condition. (f) Output curves of the phototransistor in the dark condition. Solid and dashed curves were measured during forward and backward sweepings, respectively.CC BY · PubMed Central
Figure 3 Performance of the perovskite phototransistors. (a) Photoresponsivity (R) characteristics of the CH3NH3PbI3 phototransistor under white-light illumination (power density= 10 mW cm−2). (b) EQE and R of the hybrid perovskite photodetector at different wavelength and a VDS of −30 V.
Figure 3 Performance of the perovskite phototransistors. (a) Photoresponsivity (R) characteristics of the CH3NH3PbI3 phototransistor under white-light illumination (power density= 10 mW cm−2). (b) EQE and R of the hybrid perovskite photodetector at different wavelength and a VDS of −30 V.CC BY · PubMed Central
Figure 4 Characteristics of the CH3NH3PbI3−xClx-based phototransistors. (a) Transfer curves of the CH3NH3PbI3−xClx phototransistor in the dark (black and red symbols) and under light illumination (blue and magenta symbols). (b,c) Representation of the transfer characteristics of p-type and n-type behaviours, respectively, under light illumination.
Figure 4 Characteristics of the CH3NH3PbI3−xClx-based phototransistors. (a) Transfer curves of the CH3NH3PbI3−xClx phototransistor in the dark (black and red symbols) and under light illumination (blue and magenta symbols). (b,c) Representation of the transfer characteristics of p-type and n-type behaviours, respectively, under light illumination.CC BY · PubMed Central
Figure 5 Photocurrent response of the perovskite phototransistors. (a) Photocurrent responses of the phototransistors on light illumination showing time-dependent photosensitivity with a time interval of 0.5 s at VGS=−30 V and VDS=−30 V. (b) Temporal photocurrent responses highlighting a rise time of 6.5 μs and a decay time of 5.0 μs. (c) Gate voltage-dependent photoresponses measured at VDS=−30 V. The device was measured at VGS of 0 V (red squares), −30 V (blue circles) and −40 V (magenta diamonds).
Figure 5 Photocurrent response of the perovskite phototransistors. (a) Photocurrent responses of the phototransistors on light illumination showing time-dependent photosensitivity with a time interval of 0.5 s at VGS=−30 V and VDS=−30 V. (b) Temporal photocurrent responses highlighting a rise time of 6.5 μs and a decay time of 5.0 μs. (c) Gate voltage-dependent photoresponses measured at VDS=−30 V. The device was measured at VGS of 0 V (red squares), −30 V (blue circles) and −40 V (magenta diamonds).CC BY · PubMed Central
Figure 6 Stability and reproducibility of the perovskite phototransistors. (a) Transfer curves under light illumination of the Device-P (with the PMMA-protective layer) immediately following fabrication and after storing under ambient conditions for 60 days. (b) Transfer characteristics under light illumination of the as-fabricated Device-U (without PMMA-protective layer). Inset, data measured after storing under ambient conditions for 60 days. (c) Mobility and on/off ratio of Device-P measured during 60 days of storage under ambient conditions. Stability data of Device-U are also shown in the inset for comparison. (d) Histogram of the hole mobilities measured on 20 devices with the PMMA-protective layer and 20 devices without the protective layer.
Figure 6 Stability and reproducibility of the perovskite phototransistors. (a) Transfer curves under light illumination of the Device-P (with the PMMA-protective layer) immediately following fabrication and after storing under ambient conditions for 60 days. (b) Transfer characteristics under light illumination of the as-fabricated Device-U (without PMMA-protective layer). Inset, data measured after storing under ambient conditions for 60 days. (c) Mobility and on/off ratio of Device-P measured during 60 days of storage under ambient conditions. Stability data of Device-U are also shown in the inset for comparison. (d) Histogram of the hole mobilities measured on 20 devices with the PMMA-protective layer and 20 devices without the protective layer.CC BY · PubMed Central

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 87 references

Cited by

Items 601–632 of 632

Metadata

Authors
Li, F., Ma, C., Wang, H., Hu, W., Yu, W., Sheikh, A. D., & Wu, T.
Affiliations
King Abdullah University of Science and Technology (SA)
Corresponding author
  • Li, Feng
  • Wu, Tom
Venue
Nature Communications
Published
2015-09-08
Volume
6
Issue
1
Pages
8238-8238
ISSN
2041-1723 (ISSN-L)
OpenAlex
W1628185018
Cited by
629
References
85
Citations by year
2026: 21 · 2025: 28 · 2024: 32 · 2023: 29 · 2022: 61 · 2021: 87 · 2020: 84 · 2019: 79 · 2018: 88 · 2017: 72 · 2016: 41 · 2015: 7
FWCI
33.43
Type
journal article
Language
en
Open access
Licence
Locations
  • Nature Communications (publishedVersion, cc-by)
  • Europe PMC (PubMed Central) (publishedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • arXiv (Cornell University) (submittedVersion)
  • RePEc: Research Papers in Economics (submittedVersion)
  • King Abdullah University of Science and Technology Repository (King Abdullah University of Science and Technology) (submittedVersion, cc-by)
  • arXiv (Cornell University)
Funders
King Abdullah University of Science and Technology
Topics
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Perovskite Materials and Applications
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Organic Electronics and Photovoltaics
  • Physical Sciences › Materials Science › Materials Chemistry › 2D Materials and Applications
Keywords
organic-inorganic hybrid perovskites, phototransistor, ambipolar transport, organolead halide perovskites, mixed-halide perovskites, field-effect mobility, photoresponsivity, ultrafast photoresponse, solution-processed devices, photoelectric devices

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.