Multimodal electron microscopy of halide perovskite interfacial dynamics
Open accessPublished version of a preprint
The DOI matches its Crossref record; 56 of the 56 references it cites were found in a registry or an index; 7 of the 30 sources its claims cite were checked for support.
Abstract
Abstract Halide perovskite light-emitting diodes promise high-efficiency 1–3 , low-cost optoelectronics, yet their operational instability remains a critical barrier to practical deployment. Here we develop a multimodal in situ electron microscopy approach that integrates four-dimensional scanning transmission electron microscopy, energy-dispersive X-ray spectroscopy and atomic-resolution imaging to directly visualize structural and chemical evolution in a working halide perovskite light-emitting diode with nanometre precision. Our in situ biasing measurements uncover nanoscale structural and chemical transformations initiated at transport layer interfaces, including the formation of metallic lead and lead-rich secondary phases, as well as strain-driven grain fragmentation. On biasing, we observe the partial transformation of the metallic Al contact to insulating AlCl 3 . Crucially, whereas the bulk of the perovskite emitter remains relatively intact, our experiment shows that degradation is localized at interfaces. By comparing in situ and ex situ measurements, these results establish a mechanistic link between interfacial strain, ionic transport and electrochemical reactions in working devices, and provide a broadly applicable framework for nanoscale degradation analysis in complex multilayered optoelectronic systems using multimodal in situ biasing microscopy.
Overview
CoChat Summary
## TL;DR
This paper uses in situ multimodal electron microscopy to follow a working halide perovskite LED under electrical bias and finds that failure is driven mainly by interfacial, not bulk, degradation. The authors link this degradation to strain, ion migration, formation of lead-rich phases, and corrosion of the Al contact into AlCl3.
## Key findings
- A sky-blue PeLED showed an initial electroluminescence peak at 485 nm, a 15 nm full-width at half-maximum, and a peak luminance exceeding 9,500 cd m−2 at 10.8 V; its operational lifetime (T50) was ~3 min at 1 mA cm−2.
- Under 0.2 nA constant current bias, low-dose 4D-STEM datasets were collected at 0, 3, 6, 15, 25, and 35 min, revealing a substantial nonlinear increase in driving voltage, consistent with rising device resistivity.
- Biasing caused the emitter/transport-layer interfaces to lose orthorhombic CsPbX3 and form lead-rich phases, primarily CsPb2X5 and PbX2; by 35 min, the paper reports substantial degradation at both ETL/emitter and emitter/HTL interfaces.
- The cathode also degraded: AlCl3 diffraction peaks appeared after 6 min of biasing, and the AlCl3 layer grew to around 10.8 nm after 35 min.
- The authors report that the emitter bulk remained relatively intact, and conclude that interfacial reactions, rather than bulk perovskite decomposition, mainly account for electroluminescence loss.
## Methods
- The study used a cross-sectional nanoLED PeLED mounted on a MEMS chip for in situ electrical biasing inside an aberration-corrected electron microscope.
- The device architecture included ITO/PTAA/PVK/PVP/Cs1.2FA0.3Pb(Br0.65Cl0.35)3/TPBi/LiF/Al; the FIB-prepared lamella was about 100 nm thick.
- Main analyses combined low-dose 4D-STEM, STEM-EDX, atomic-resolution HAADF-STEM, geometric phase analysis for strain, and NMF / template-matching diffraction indexing to track structural and compositional changes over time.
## Limitations
- The paper states that Joule heating was not directly measured; it is discussed as a likely contributing factor based on correlations in the data.
- The paper notes that the work was performed on a lamella/nanoLED geometry and then validated with ex situ bulk-device measurements; this makes some observations potentially sensitive to geometry, although the authors argue the mechanisms are intrinsic.
- The text makes evident that the study is focused on a single device class and composition; broader generalization to other perovskite LED architectures is not stated in the paper.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures
![Fig. 1 In situ biasing multimodal electron microscopy of a perovskite blue light-emitting diode. a, Schematic diagram of the STEM detectors used for the galvanostatic study of the nanoLED device, with biasing configuration of the Al/LiF and indium tin oxide (ITO) contacts. The nanoLED cross-section is 40 μm wide and 100 nm thick. b, Current–voltage and luminance characteristics of the pristine device, showing an emission peak at 485 nm (inset). c, STEM-HAADF cross-section of the nanoLED device stack. d,e, Atomic-resolution STEM-HAADF image (d) of the perovskite emitter with the corresponding fast Fourier transform (e), showing an orthorhombic structure with a (020) interplanar spacing of 0.58 nm. f, Ideal orthorhombic lattice structure of the perovskite emissive layer seen along the [101] zone axis. Scale bars, 200 nm (c), 1 nm (d), 2 nm−1 (e). Source data](https://figures.cochat.ai/paper-figures/21959dec6cb44228ac1fbb705d3f0356/multimodal-electron-microscopy-of-halide-perovskite-interfacial-dynamics-figure-1.jpg)


![Fig. 4 Interfacial degradation at transport layer–perovskite emitter interfaces under bias. a–d, Summed diffraction patterns (150 pixels) at the ETL/emitter and HTL/emitter interfaces under pristine conditions (tbias = 0 min) and after 35 min under bias. Red labels denote diffraction features assigned to PbX2; yellow labels indicate reflections matched to the pristine orthorhombic perovskite; green labels denote CsPb2X5. a,b, Show a good match to the orthorhombic perovskite emitter near the ETL (a) and evidence of PbX2 formation near the HTL (b). c,d, Pb-rich phases (CsPb2X5, PbX2) emerge at the ETL/emitter interface (c) and the emitter/HTL interface (d) after 35 min of biasing, which remains oriented along the [100] zone axis. e,f, Schematic illustrations show the pristine state of the interfaces with emitter at 0 min of biasing (e) and progressive phase transformations at the interfaces with the emitter after 35 min of biasing (f). The dashed lines represent the interfaces of ETL/emitter and emitter/HTL. At the pristine state, the interfaces show a small amount of the Pb-rich regions, which are negligible compared with the biased region. Scale bars, 2 nm−1.](https://figures.cochat.ai/paper-figures/759cf43ac3d7442c8dca2f6fe6d5f5d2/multimodal-electron-microscopy-of-halide-perovskite-interfacial-dynamics-figure-4.jpg)



Verification
Claims the paper makes
5 Valid · 2 Not valid · 8 Not checked · 70 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“The presence of Pb-rich phases in the as-prepared device probably arises from compositional inhomogeneity or interfacial reactions during film formation and processing36”
§ Multimodal electron microscopy of halide perovskite interfacial dynamics > Atomic-scale interfacial strain mapping
What the sources say
- Disputedcites [36] Liang, J. et al. Origins and influences of metallic lead in perovskite solar cells. Joule 6, 816–833 (2022). sourceExperimental — accuracy not yet measured
The Results and discussion (page unavailable) say that metallic Pb impurities were absent from the initial perovskite films and arose from PbI2 decomposition during XPS testing, not from the precursor solutions. The Introduction (page unavailable) likewise identifies light or X-ray irradiation of residual PbI2 as their origin, rather than compositional inhomogeneity or interfacial reactions during fabrication. (LLM, conf=0.84)
Checked by a reasoning model — may be wrong.
hedgedstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“In-plane strain often accumulates near grain boundaries and misoriented regions in the perovskite lattice, resulting from mismatches during crystallization or film formation38”
§ Multimodal electron microscopy of halide perovskite interfacial dynamics > Atomic-scale interfacial strain mapping
What the sources say
- Partly supportedcites [38] Jariwala, S. et al. Local crystal misorientation influences non-radiative recombination in halide perovskites. Joule 3, 3048–3060 (2019). sourceExperimental — accuracy not yet measured
The Results section (p. n/a, Fig. 3 discussion) does attribute local strain to grain/sub-grain boundaries and to events during film formation: 'phase transition from cubic to tetragonal CH3NH3PbI3 during film formation can introduce a significant amount of local residual stresses... These micro-stresses may be concentrated at the grain boundaries and sub-grain boundaries within the grain,' and it reports 'higher misorientation angles... closer to the grain boundaries suggesting a higher degree of lattice rotation or lattice bending near grain boundaries.' However, the source hedges the accumulation ('may be concentrated', 'can introduce') where the citing sentence states it as a frequent fact ('often accumulates'), and the source never characterises the strain as specifically 'in-plane' — it speaks of local/near-surface residual strain inferred from EBSD orientation spread. The mechanism given is thermal-expansion anisotropy and the cubic-to-tetragonal phase transition, only loosely the claim's generic 'mismatches during crystallization or film formation.' (LLM, conf=0.75)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Intensive peaks belonging to Pb-rich phases, confirmed by a non-negative matrix factorization (NMF) decomposed diffraction pattern (Supplementary Fig. 6), are detected after 25 min biasing”
§ Multimodal electron microscopy of halide perovskite interfacial dynamics > Structural and compositional evolution To monitor the structural and compositional evolution of the active layers, a constant current of 0.2 nA was applied to the nanoLED, equivalent to a current density of 1 mA cm−2 for the pristine full device driven at 4 V. Given the beam-sensitive nature of the emitter, low-dose 4D-STEM datasets (lower than 8 e−/Å−2 per frame) were acquired with a lateral spatial resolution of approximately 2 nm to produce nanoscale diffraction maps after 0, 3, 6, 15, 25 and 35 min of biasing. Each time point was acquired from a distinct yet equivalent region to minimize cumulative beam damage (Supplementary Fig. 5). Low-current 4D-STEM and EDX spectrum images were acquired from each region, after which the voltage and current were temporarily set to zero to systematically investigate structural, morphological and compositional evolution. The evolution of the average driving voltage to maintain galvanostatic conditions versus time profile is shown in Fig. 3a. A substantial nonlinear increase was observed throughout the experiment, indicating a progressive increase in device resistivity due to structural and compositional degradation. Figure 3b presents summed one-dimensional radial electron diffraction from perovskite emitters, highlighting systematic peak broadening and intensity redistribution from 0 to 35 min biasing, indicative of increased lattice disorder due to accumulated structural defects and heterogeneity. Pristine perovskite emitters (t = 0 min) confirm retention of orthorhombic symmetry (Pnma) at room temperature, consistent with thermodynamically stabilized perovskite structures40. Initial diffraction peaks correspond primarily to (121), (040) and (042) at 0.245, 0.343 and 0.425 Å−1, aligning closely with [010] and [100] orientations. Peaks at (040) and (042) shift towards larger d spacings in early biasing regions, reflecting electric-field-induced lattice distortions. Intensive peaks belonging to Pb-rich phases, confirmed by a non-negative matrix factorization (NMF) decomposed diffraction pattern (Supplementary Fig. 6), are detected after 25 min biasing and shown as red spots. Quantitative lattice parameter analysis together with the traces Δa/a0, Δb/b0, Δc/c0 (t = 0 baseline) (Fig. 3c, Supplementary Fig. 7 and Supplementary Table 1) reveal a non-monotonic orthorhombic lattice evolution. Both a and b axes reveal an initial expansion during early biasing stages, whereas c exhibits a net contraction before 25 min of biasing. By 25 min, both b and c axes show a partial return towards pre-bias values, reflecting a local strain accommodation, potentially owing to defect migration or phase reorganization41,42. At 35 min biasing, the a and c axes collapse, whereas b remains only weakly perturbed (around ±2%), signalling severe distortions in octahedra and loss of structural coherence. This late-time structural deterioration coincides with the sharp increase in driving voltage, linking field-driven interfacial chemistry and mechanically mediated lattice failure to the observed electrical throttling. STEM-HAADF images of perovskite emitters in the six regions at pristine and corresponding virtual dark-field (vDF) images after biasing reveal progressive morphological changes (Fig. 3d). These contrast variations and clustered features reflect localized decomposition processes that become most pronounced after 25 min biasing, consistent with phase segregation and microstructural breakdown observed in the diffraction patterns. We hypothesize that this degradation is primarily driven by ion migration and spatially inhomogeneous Joule heating, where local current densities and resistive hotspots may lead to differential thermal stresses at specific sites. Although we do not directly measure Joule heating in this work, the correlation between increased resistivity, structural disruption and Pb-rich phase formation supports this mechanism as a contributing factor. Cross-sectional area and intensity (mass) analysis of the emitter (Fig. 3e) pre-biasing and post-biasing, show about 10.5% and 24.2% loss by 35 min biasing, indicating substantial volatilization and structural collapse. The high mismatch of mass and area loss after 25 min of biasing suggests local densification, probably from increased Pb-rich phase formation or porous grain collapse. Intragrain metrics (Fig. 3f) support these structural observations. The median intragrain size and grain orientation spread initially increase in early biasing (t ≤ 6 min), then sharply decreases after 15 min biasing, indicative of grain fragmentation with partial structural accommodation due to increased defective phase formation (Supplementary Figs. 8 and 9). Comparison of radial profiles between 0 min and 35 min biasing (Extended Data Fig. 2a) reveals substantial metallic Pb formation after biasing (up to 6 V). Fourier-filtered imaging (Extended Data Fig. 2b) identifies metallic Pb nanoparticles with distinct (111) and (002) lattice spacings (0.294 nm and 0.250 nm, respectively), highlighting structural integrity loss. The formation of metallic Pb is probably initiated by halide oxidation and subsequent electrochemical reduction of undercoordinated Pb2+. This transformation marks advanced degradation, as metallic Pb introduces non-radiative recombination pathways that reduce electroluminescence efficiency36. NMF components derived from STEM-EDX (Fig. 3g,i) confirm Pb-rich phase formation after 35 min of biasing, further exacerbating structural and compositional instability. Similar phase segregation is detected from 3 to 25 min biasing (Supplementary Fig. 10), demonstrating a progressive trend of Pb enrichment during in situ biasing measurements. The PbBr2 phase formation near the HTL indicates the retention and partial reorganization of Br− ions in regions, reinforcing halide segregation as a key driver of phase evolution and degradation43. This bias-induced segregation provides direct structural evidence of electrochemical degradation mechanisms that undermine device stability and optoelectronic performance. Despite the progressive compositional degradation, substantial portions of the orthorhombic perovskite persist in the bulk (Fig. 3h and Supplementary Fig. 10). The electroluminescence diminishes markedly after 35 min, whereas photoluminescence shows less of a decline ratio (Supplementary Fig. 1a,c), indicating that radiative recombination centres are largely intact. Thus, degradation at interfaces between emitter and transport layers rather than bulk perovskite decomposition primarily accounts for electroluminescence loss, impeding charge transport and increasing device resistivity. The aluminium contact layer (cathode) plays a pivotal role in facilitating electron injection into the perovskite emitter. In the pristine device, minor Al2O3 signals were detected (Extended Data Fig. 2c), arising from ambient oxidation during fabrication and storage. On biasing, new AlCl3 diffraction peaks emerge, evidencing chemical interactions between aluminium and mobile Cl− ions (Supplementary Fig. 11). This aligns with previous studies of halide-driven corrosion reactions in perovskite optoelectronics43,44, enabled by higher mobility of chloride ions owing to their smaller ionic radius and lower migration barrier (0.22 eV for Cl−, 0.47 eV for Br−)45. Correlative STEM-EDX NMF component analyses across all biased regions (Fig. 3j and Supplementary Fig. 10) confirm the first presence of the AlCl3 layer after 6 min of biasing, increasing to around 10.8 nm after 35 min biasing. The newly formed insulating AlCl3 layer hinders electron injection, exacerbating Joule heating and accelerating both physical and chemical electrode corrosion. Such substantial electrode deterioration contributes to localized electroluminescence quenching, observed as dark spots, and shifts the recombination zone towards the cathode46,47. Additionally, continual halide ion consumption at the cathode interface destabilizes the perovskite emitter, driving further structural decomposition and local defect densities, and consequently reducing overall device efficiency and lifetime48. To verify that lamella-biasing faithfully captures device-relevant processes, we performed ex situ STEM-EDX analysis on biased bulk PeLEDs (1 mA cm−2, 15–45 min). The same interfacial degradation products were observed, including insulating AlCl3 at the cathode and lead-rich phases at the interfaces between the transport layers and the perovskite, whereas the emitter interior remained comparatively intact. These post-mortem observations corroborate that the dominant degradation mechanisms are intrinsic and largely geometry independent (Supplementary Figs. 12–15), highlighting chloride migration and electrode corrosion as key failure mechanisms and underscoring the need for robust interfacial stabilization strategies.
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“By 25 min, both b and c axes show a partial return towards pre-bias values, reflecting a local strain accommodation”
§ Multimodal electron microscopy of halide perovskite interfacial dynamics > Structural and compositional evolution To monitor the structural and compositional evolution of the active layers, a constant current of 0.2 nA was applied to the nanoLED, equivalent to a current density of 1 mA cm−2 for the pristine full device driven at 4 V. Given the beam-sensitive nature of the emitter, low-dose 4D-STEM datasets (lower than 8 e−/Å−2 per frame) were acquired with a lateral spatial resolution of approximately 2 nm to produce nanoscale diffraction maps after 0, 3, 6, 15, 25 and 35 min of biasing. Each time point was acquired from a distinct yet equivalent region to minimize cumulative beam damage (Supplementary Fig. 5). Low-current 4D-STEM and EDX spectrum images were acquired from each region, after which the voltage and current were temporarily set to zero to systematically investigate structural, morphological and compositional evolution. The evolution of the average driving voltage to maintain galvanostatic conditions versus time profile is shown in Fig. 3a. A substantial nonlinear increase was observed throughout the experiment, indicating a progressive increase in device resistivity due to structural and compositional degradation. Figure 3b presents summed one-dimensional radial electron diffraction from perovskite emitters, highlighting systematic peak broadening and intensity redistribution from 0 to 35 min biasing, indicative of increased lattice disorder due to accumulated structural defects and heterogeneity. Pristine perovskite emitters (t = 0 min) confirm retention of orthorhombic symmetry (Pnma) at room temperature, consistent with thermodynamically stabilized perovskite structures40. Initial diffraction peaks correspond primarily to (121), (040) and (042) at 0.245, 0.343 and 0.425 Å−1, aligning closely with [010] and [100] orientations. Peaks at (040) and (042) shift towards larger d spacings in early biasing regions, reflecting electric-field-induced lattice distortions. Intensive peaks belonging to Pb-rich phases, confirmed by a non-negative matrix factorization (NMF) decomposed diffraction pattern (Supplementary Fig. 6), are detected after 25 min biasing and shown as red spots. Quantitative lattice parameter analysis together with the traces Δa/a0, Δb/b0, Δc/c0 (t = 0 baseline) (Fig. 3c, Supplementary Fig. 7 and Supplementary Table 1) reveal a non-monotonic orthorhombic lattice evolution. Both a and b axes reveal an initial expansion during early biasing stages, whereas c exhibits a net contraction before 25 min of biasing. By 25 min, both b and c axes show a partial return towards pre-bias values, reflecting a local strain accommodation, potentially owing to defect migration or phase reorganization41,42. At 35 min biasing, the a and c axes collapse, whereas b remains only weakly perturbed (around ±2%), signalling severe distortions in octahedra and loss of structural coherence. This late-time structural deterioration coincides with the sharp increase in driving voltage, linking field-driven interfacial chemistry and mechanically mediated lattice failure to the observed electrical throttling. STEM-HAADF images of perovskite emitters in the six regions at pristine and corresponding virtual dark-field (vDF) images after biasing reveal progressive morphological changes (Fig. 3d). These contrast variations and clustered features reflect localized decomposition processes that become most pronounced after 25 min biasing, consistent with phase segregation and microstructural breakdown observed in the diffraction patterns. We hypothesize that this degradation is primarily driven by ion migration and spatially inhomogeneous Joule heating, where local current densities and resistive hotspots may lead to differential thermal stresses at specific sites. Although we do not directly measure Joule heating in this work, the correlation between increased resistivity, structural disruption and Pb-rich phase formation supports this mechanism as a contributing factor. Cross-sectional area and intensity (mass) analysis of the emitter (Fig. 3e) pre-biasing and post-biasing, show about 10.5% and 24.2% loss by 35 min biasing, indicating substantial volatilization and structural collapse. The high mismatch of mass and area loss after 25 min of biasing suggests local densification, probably from increased Pb-rich phase formation or porous grain collapse. Intragrain metrics (Fig. 3f) support these structural observations. The median intragrain size and grain orientation spread initially increase in early biasing (t ≤ 6 min), then sharply decreases after 15 min biasing, indicative of grain fragmentation with partial structural accommodation due to increased defective phase formation (Supplementary Figs. 8 and 9). Comparison of radial profiles between 0 min and 35 min biasing (Extended Data Fig. 2a) reveals substantial metallic Pb formation after biasing (up to 6 V). Fourier-filtered imaging (Extended Data Fig. 2b) identifies metallic Pb nanoparticles with distinct (111) and (002) lattice spacings (0.294 nm and 0.250 nm, respectively), highlighting structural integrity loss. The formation of metallic Pb is probably initiated by halide oxidation and subsequent electrochemical reduction of undercoordinated Pb2+. This transformation marks advanced degradation, as metallic Pb introduces non-radiative recombination pathways that reduce electroluminescence efficiency36. NMF components derived from STEM-EDX (Fig. 3g,i) confirm Pb-rich phase formation after 35 min of biasing, further exacerbating structural and compositional instability. Similar phase segregation is detected from 3 to 25 min biasing (Supplementary Fig. 10), demonstrating a progressive trend of Pb enrichment during in situ biasing measurements. The PbBr2 phase formation near the HTL indicates the retention and partial reorganization of Br− ions in regions, reinforcing halide segregation as a key driver of phase evolution and degradation43. This bias-induced segregation provides direct structural evidence of electrochemical degradation mechanisms that undermine device stability and optoelectronic performance. Despite the progressive compositional degradation, substantial portions of the orthorhombic perovskite persist in the bulk (Fig. 3h and Supplementary Fig. 10). The electroluminescence diminishes markedly after 35 min, whereas photoluminescence shows less of a decline ratio (Supplementary Fig. 1a,c), indicating that radiative recombination centres are largely intact. Thus, degradation at interfaces between emitter and transport layers rather than bulk perovskite decomposition primarily accounts for electroluminescence loss, impeding charge transport and increasing device resistivity. The aluminium contact layer (cathode) plays a pivotal role in facilitating electron injection into the perovskite emitter. In the pristine device, minor Al2O3 signals were detected (Extended Data Fig. 2c), arising from ambient oxidation during fabrication and storage. On biasing, new AlCl3 diffraction peaks emerge, evidencing chemical interactions between aluminium and mobile Cl− ions (Supplementary Fig. 11). This aligns with previous studies of halide-driven corrosion reactions in perovskite optoelectronics43,44, enabled by higher mobility of chloride ions owing to their smaller ionic radius and lower migration barrier (0.22 eV for Cl−, 0.47 eV for Br−)45. Correlative STEM-EDX NMF component analyses across all biased regions (Fig. 3j and Supplementary Fig. 10) confirm the first presence of the AlCl3 layer after 6 min of biasing, increasing to around 10.8 nm after 35 min biasing. The newly formed insulating AlCl3 layer hinders electron injection, exacerbating Joule heating and accelerating both physical and chemical electrode corrosion. Such substantial electrode deterioration contributes to localized electroluminescence quenching, observed as dark spots, and shifts the recombination zone towards the cathode46,47. Additionally, continual halide ion consumption at the cathode interface destabilizes the perovskite emitter, driving further structural decomposition and local defect densities, and consequently reducing overall device efficiency and lifetime48. To verify that lamella-biasing faithfully captures device-relevant processes, we performed ex situ STEM-EDX analysis on biased bulk PeLEDs (1 mA cm−2, 15–45 min). The same interfacial degradation products were observed, including insulating AlCl3 at the cathode and lead-rich phases at the interfaces between the transport layers and the perovskite, whereas the emitter interior remained comparatively intact. These post-mortem observations corroborate that the dominant degradation mechanisms are intrinsic and largely geometry independent (Supplementary Figs. 12–15), highlighting chloride migration and electrode corrosion as key failure mechanisms and underscoring the need for robust interfacial stabilization strategies.
plainstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Comparison of radial profiles between 0 min and 35 min biasing (Extended Data Fig. 2a) reveals substantial metallic Pb formation after biasing (up to 6 V)”
§ Multimodal electron microscopy of halide perovskite interfacial dynamics > Structural and compositional evolution To monitor the structural and compositional evolution of the active layers, a constant current of 0.2 nA was applied to the nanoLED, equivalent to a current density of 1 mA cm−2 for the pristine full device driven at 4 V. Given the beam-sensitive nature of the emitter, low-dose 4D-STEM datasets (lower than 8 e−/Å−2 per frame) were acquired with a lateral spatial resolution of approximately 2 nm to produce nanoscale diffraction maps after 0, 3, 6, 15, 25 and 35 min of biasing. Each time point was acquired from a distinct yet equivalent region to minimize cumulative beam damage (Supplementary Fig. 5). Low-current 4D-STEM and EDX spectrum images were acquired from each region, after which the voltage and current were temporarily set to zero to systematically investigate structural, morphological and compositional evolution. The evolution of the average driving voltage to maintain galvanostatic conditions versus time profile is shown in Fig. 3a. A substantial nonlinear increase was observed throughout the experiment, indicating a progressive increase in device resistivity due to structural and compositional degradation. Figure 3b presents summed one-dimensional radial electron diffraction from perovskite emitters, highlighting systematic peak broadening and intensity redistribution from 0 to 35 min biasing, indicative of increased lattice disorder due to accumulated structural defects and heterogeneity. Pristine perovskite emitters (t = 0 min) confirm retention of orthorhombic symmetry (Pnma) at room temperature, consistent with thermodynamically stabilized perovskite structures40. Initial diffraction peaks correspond primarily to (121), (040) and (042) at 0.245, 0.343 and 0.425 Å−1, aligning closely with [010] and [100] orientations. Peaks at (040) and (042) shift towards larger d spacings in early biasing regions, reflecting electric-field-induced lattice distortions. Intensive peaks belonging to Pb-rich phases, confirmed by a non-negative matrix factorization (NMF) decomposed diffraction pattern (Supplementary Fig. 6), are detected after 25 min biasing and shown as red spots. Quantitative lattice parameter analysis together with the traces Δa/a0, Δb/b0, Δc/c0 (t = 0 baseline) (Fig. 3c, Supplementary Fig. 7 and Supplementary Table 1) reveal a non-monotonic orthorhombic lattice evolution. Both a and b axes reveal an initial expansion during early biasing stages, whereas c exhibits a net contraction before 25 min of biasing. By 25 min, both b and c axes show a partial return towards pre-bias values, reflecting a local strain accommodation, potentially owing to defect migration or phase reorganization41,42. At 35 min biasing, the a and c axes collapse, whereas b remains only weakly perturbed (around ±2%), signalling severe distortions in octahedra and loss of structural coherence. This late-time structural deterioration coincides with the sharp increase in driving voltage, linking field-driven interfacial chemistry and mechanically mediated lattice failure to the observed electrical throttling. STEM-HAADF images of perovskite emitters in the six regions at pristine and corresponding virtual dark-field (vDF) images after biasing reveal progressive morphological changes (Fig. 3d). These contrast variations and clustered features reflect localized decomposition processes that become most pronounced after 25 min biasing, consistent with phase segregation and microstructural breakdown observed in the diffraction patterns. We hypothesize that this degradation is primarily driven by ion migration and spatially inhomogeneous Joule heating, where local current densities and resistive hotspots may lead to differential thermal stresses at specific sites. Although we do not directly measure Joule heating in this work, the correlation between increased resistivity, structural disruption and Pb-rich phase formation supports this mechanism as a contributing factor. Cross-sectional area and intensity (mass) analysis of the emitter (Fig. 3e) pre-biasing and post-biasing, show about 10.5% and 24.2% loss by 35 min biasing, indicating substantial volatilization and structural collapse. The high mismatch of mass and area loss after 25 min of biasing suggests local densification, probably from increased Pb-rich phase formation or porous grain collapse. Intragrain metrics (Fig. 3f) support these structural observations. The median intragrain size and grain orientation spread initially increase in early biasing (t ≤ 6 min), then sharply decreases after 15 min biasing, indicative of grain fragmentation with partial structural accommodation due to increased defective phase formation (Supplementary Figs. 8 and 9). Comparison of radial profiles between 0 min and 35 min biasing (Extended Data Fig. 2a) reveals substantial metallic Pb formation after biasing (up to 6 V). Fourier-filtered imaging (Extended Data Fig. 2b) identifies metallic Pb nanoparticles with distinct (111) and (002) lattice spacings (0.294 nm and 0.250 nm, respectively), highlighting structural integrity loss. The formation of metallic Pb is probably initiated by halide oxidation and subsequent electrochemical reduction of undercoordinated Pb2+. This transformation marks advanced degradation, as metallic Pb introduces non-radiative recombination pathways that reduce electroluminescence efficiency36. NMF components derived from STEM-EDX (Fig. 3g,i) confirm Pb-rich phase formation after 35 min of biasing, further exacerbating structural and compositional instability. Similar phase segregation is detected from 3 to 25 min biasing (Supplementary Fig. 10), demonstrating a progressive trend of Pb enrichment during in situ biasing measurements. The PbBr2 phase formation near the HTL indicates the retention and partial reorganization of Br− ions in regions, reinforcing halide segregation as a key driver of phase evolution and degradation43. This bias-induced segregation provides direct structural evidence of electrochemical degradation mechanisms that undermine device stability and optoelectronic performance. Despite the progressive compositional degradation, substantial portions of the orthorhombic perovskite persist in the bulk (Fig. 3h and Supplementary Fig. 10). The electroluminescence diminishes markedly after 35 min, whereas photoluminescence shows less of a decline ratio (Supplementary Fig. 1a,c), indicating that radiative recombination centres are largely intact. Thus, degradation at interfaces between emitter and transport layers rather than bulk perovskite decomposition primarily accounts for electroluminescence loss, impeding charge transport and increasing device resistivity. The aluminium contact layer (cathode) plays a pivotal role in facilitating electron injection into the perovskite emitter. In the pristine device, minor Al2O3 signals were detected (Extended Data Fig. 2c), arising from ambient oxidation during fabrication and storage. On biasing, new AlCl3 diffraction peaks emerge, evidencing chemical interactions between aluminium and mobile Cl− ions (Supplementary Fig. 11). This aligns with previous studies of halide-driven corrosion reactions in perovskite optoelectronics43,44, enabled by higher mobility of chloride ions owing to their smaller ionic radius and lower migration barrier (0.22 eV for Cl−, 0.47 eV for Br−)45. Correlative STEM-EDX NMF component analyses across all biased regions (Fig. 3j and Supplementary Fig. 10) confirm the first presence of the AlCl3 layer after 6 min of biasing, increasing to around 10.8 nm after 35 min biasing. The newly formed insulating AlCl3 layer hinders electron injection, exacerbating Joule heating and accelerating both physical and chemical electrode corrosion. Such substantial electrode deterioration contributes to localized electroluminescence quenching, observed as dark spots, and shifts the recombination zone towards the cathode46,47. Additionally, continual halide ion consumption at the cathode interface destabilizes the perovskite emitter, driving further structural decomposition and local defect densities, and consequently reducing overall device efficiency and lifetime48. To verify that lamella-biasing faithfully captures device-relevant processes, we performed ex situ STEM-EDX analysis on biased bulk PeLEDs (1 mA cm−2, 15–45 min). The same interfacial degradation products were observed, including insulating AlCl3 at the cathode and lead-rich phases at the interfaces between the transport layers and the perovskite, whereas the emitter interior remained comparatively intact. These post-mortem observations corroborate that the dominant degradation mechanisms are intrinsic and largely geometry independent (Supplementary Figs. 12–15), highlighting chloride migration and electrode corrosion as key failure mechanisms and underscoring the need for robust interfacial stabilization strategies.
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
44 more claims
Create a free account to see all 85 claims and to verify the 3 references still open.
- It may state two separate claims as one. 30
- Probably not a substantial claim. 7
Citations
Cites
Sequential deposition as a route to high-performance perovskite-sensitized solar cells
Burschka, J., Pellet, N., Moon, S.-J., Humphry-Baker, R., Gao, P., Nazeeruddin, M. K., & Grätzel, M. (2013) · Nature · doi:10.1038/nature12340 · Cited by 9,547
Bright light-emitting diodes based on organometal halide perovskite
Tan, Z.-K., Moghaddam, R. S., Lai, M. L., Docampo, P., Higler, R., Deschler, F., Price, M., Sadhanala, A., Pazos, L. M., Credgington, D., et al. (2014) · Nature Nanotechnology · doi:10.1038/nnano.2014.149 · Cited by 4,450 · cited 1×
“These properties have enabled rapid advancements in perovskite-based photovoltaics 4,5 , light-emitting diodes (LEDs) 6,7 , photodetectors 8,9 and lasers 10,11 .”
Self-citationQuantitative measurement of displacement and strain fields from HREM micrographs
Hÿtch, M. J., Snoeck, E., & Kilaas, R. (1998) · Ultramicroscopy · doi:10.1016/s0304-3991(98)00035-7 · Cited by 2,752 · cited 1×
“…a well-established technique for deformation analysis 30–32 , was used following the Hÿtch formalism to evaluate the relationship between lattice displacement and phase differences between emitter and defective Pb-rich phases in high-resolution STEM images through lattice strain maps 33–36 .”
Genesis, challenges and opportunities for colloidal lead halide perovskite nanocrystals
Akkerman, Q. A., Rainò, G., Kovalenko, M. V., & Manna, L. (2018) · Nature Materials · doi:10.1038/s41563-018-0018-4 · Cited by 2,287 · cited 1×
“Pristine perovskite emitters ( t = 0 min) confirm retention of orthorhombic symmetry ( Pnma ) at room temperature, consistent with thermodynamically stabilized perovskite structures 40 .”
Challenges for commercializing perovskite solar cells
Rong, Y., Hu, Y., Mei, A., Tan, H., Saidaminov, M. I., Seok, S. I., McGehee, M. D., Sargent, E. H., & Han, H. (2018) · Science · doi:10.1126/science.aat8235 · Cited by 2,140 · cited 1×
“Such substantial electrode deterioration contributes to localized electroluminescence quenching, observed as dark spots, and shifts the recombination zone towards the cathode 46,47 .”
Highly narrowband perovskite single-crystal photodetectors enabled by surface-charge recombination
Fang, Y., Dong, Q., Shao, Y., Yuan, Y., & Huang, J. (2015) · Nature Photonics · doi:10.1038/nphoton.2015.156 · Cited by 1,470 · cited 2×
“These properties have enabled rapid advancements in perovskite-based photovoltaics 4,5 , light-emitting diodes (LEDs) 6,7 , photodetectors 8,9 and lasers 10,11 .”
Perovskite Materials for Light‐Emitting Diodes and Lasers
Veldhuis, S. A., Boix, P. P., Yantara, N., Li, M., Sum, T. C., Mathews, N., & Mhaisalkar, S. G. (2016) · Advanced Materials · doi:10.1002/adma.201600669 · Cited by 1,465
Rational molecular passivation for high-performance perovskite light-emitting diodes
Xu, W., Hu, Q., Bai, S., Bao, C., Miao, Y., Yuan, Z., Borzda, T., Barker, A. J., Tyukalova, E., Hu, Z., et al. (2019) · Nature Photonics · doi:10.1038/s41566-019-0390-x · Cited by 1,240
Self-citationHomogenizing out-of-plane cation composition in perovskite solar cells
Liang, Z., Zhang, Y., Xu, H., Chen, W., Liu, B., Zhang, J., Zhang, H., Wang, Z., Kang, D.-H., Zeng, J., et al. (2023) · Nature · doi:10.1038/s41586-023-06784-0 · Cited by 791
Origins and influences of metallic lead in perovskite solar cells
Liang, J., Hu, X., Wang, C., Liang, C., Chen, C., Xiao, M., Li, J., Tao, C., Xing, G., Yu, R., et al. (2022) · Joule · doi:10.1016/j.joule.2022.03.005 · Cited by 576 · cited 4×
“…a well-established technique for deformation analysis 30–32 , was used following the Hÿtch formalism to evaluate the relationship between lattice displacement and phase differences between emitter and defective Pb-rich phases in high-resolution STEM images through lattice strain maps 33–36 .”
Influential
Cited by
Chen, J., Luo, X., Liu, X., et al. (2026) · Science Advances · doi:10.1126/sciadv.aeg2635 · Cited by 4
“In sum, these complex and diverse surface vacancies result in QD surface structural disorders, which will accelerate QD degradation or phase transition, thereby resulting in poor QLED performance, especially under high current density or during continuous operation ( 19 , 20 ).”
Self-citationIn-Situ TEM Studies of Halide Perovskite Memristors: Mechanistic Insights and Future Directions
Mittal, G., Paul, J., Salim, R., Xing, X., Peña, T. A. D., Mathews, N., & Lam, Y. M. (2026) · Nano Letters · doi:10.1021/acs.nanolett.6c02080 · Cited by 1
Li, Z., Guo, Y., Liu, Z., Wu, J., Tang, Z., Fu, Y., & Xie, Z. (2026) · Advanced Optical Materials · doi:10.1002/adom.71306
Toward High-Efficiency Near-Infrared LEDs through Fluorocytosine-Doped Tin–Lead Halide Perovskites
Vasudevan, T., Jiang, W.-J., Ramalingam, S., & Chen, L. (2026) · ACS Applied Optical Materials · doi:10.1021/acsaom.6c00158
Multi-dimensional design of nanocatalysts for electrocatalytic oxidation of small organic molecules
Zhang, Y., Liu, L., Duan, Z., Jiao, S., Li, Q., & Fu, X. (2026) · Coordination Chemistry Reviews · doi:10.1016/j.ccr.2026.218222 · Cited by 1
Metadata
- Authors
- Li, X., Gu, Q., Huang, W., Fairclough, S. M., Friend, R. H., Stranks, S. D., Liu, T., & Ducati, C.
- Affiliations
- University of Cambridge (GB)
- Corresponding author
- Liu, Tianjun
- Ducati, Caterina
- ORCID
- Venue
- Nature
- Published
- 2026-03-11
- Volume
- 651
- Issue
- 8106
- Pages
- 614-620
- ISSN
- 0028-0836 (ISSN-L)
- 1476-4687
- PMC
- PMC12999523
- OpenAlex
- W7135016988
- Cited by
- 14
- References
- 54
- Citations by year
- 2026: 14
- FWCI
- 22.31
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0 (tdm)
- creativecommons.org/licenses/by/4.0 (vor)
- Locations
- Nature (publishedVersion, cc-by)
- Research Square (acceptedVersion, cc-by)
- PubMed (publishedVersion)
- PubMed Central (publishedVersion, cc-by)
- Apollo (University of Cambridge) (submittedVersion, cc-by)
- Funders
- Diamond Light Source
- Henry Royce Institute
- Engineering and Physical Sciences Research Council (R008779/1, EP/R008779/1)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Perovskite Materials and Applications
- Life Sciences › Biochemistry, Genetics and Molecular Biology › Structural Biology › Advanced Electron Microscopy Techniques and Applications
- Physical Sciences › Materials Science › Materials Chemistry › 2D Materials and Applications
- Keywords
- halide perovskites, perovskite light-emitting diodes, device degradation, interfacial dynamics, in situ biasing, 4D-STEM, interfacial strain, grain fragmentation, ion transport, electrochemical reactions
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol and qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Multimodal electron microscopy of halide perovskite interfacial dynamics. https://app.cochat.ai/papers/10.1038/s41586-026-10238-8
- The paper
- Li, X., Gu, Q., Huang, W., Fairclough, S. M., Friend, R. H., Stranks, S. D., Liu, T., & Ducati, C. (2026). Multimodal electron microscopy of halide perovskite interfacial dynamics. Nature. https://doi.org/10.1038/s41586-026-10238-8
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.