CoChat

Comparison of the effects of use, protection, improper renovation and removal of asbestos products on the example of typical old office buildings in Poland

Open access
Obmiński, Andrzej · 2023 · Scientific Reports

Published version of a preprint

The DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index; 7 of the 27 sources its claims cite were checked for support.

Abstract

The study focused on old, German building types “LIPSK” and “BERLIN” used in Poland, since the 1960s in Eastern Europe. The different operations on buildings were analysed: protection and maintenance of asbestos products, asbestos removal and inadvertent damage to asbestos as a result of building renovation. Measurements of respirable (countable) asbestos fibres in the air were carried out using the PCOM + PLM method and SEM–EDS. In the case of the accidental destruction of products, initial contamination was ≈7000 f/m 3 . After 16 weeks from the end of the activity and 20 days of extreme ventilation, contamination decreased to about 500 f/m 3 . At the same time, in similar rooms, without extreme ventilation, the pollution was above 4000 f/m 3 . The average increase in pollution in a dozen or so similar buildings, after asbestos removal in places beyond the work zones, ranged from ≈ 1700–2700 f/m 3 and lasted for one or two years. These buildings, used without ACM destruction or after product impregnation, have maintained low asbestos contamination < 300 f/m 3 for more than 10–20 years. So, due to the easy release of asbestos that occurs with any ACM removal and the increased risk of occupant exposure, these works are often inappropriate for the buildings in question.

Overview

CoChat Summary

## TL;DR

This paper compares airborne asbestos in old Polish office buildings under normal use, protection/encapsulation, improper renovation, asbestos removal, and demolition. It argues that leaving ACMs in place or properly protecting them can keep contamination low for years, while removal or accidental damage can produce much higher and longer-lasting airborne fiber levels.

## Key findings

  • In accidental destruction of asbestos-containing products, initial contamination was about 7000 f/m3; after 16 weeks and 20 days of extreme ventilation, it fell to about 500 f/m3, but in similar rooms without extreme ventilation it remained above 4000 f/m3.
  • After asbestos removal in buildings beyond the work zones, the average increase in pollution in a dozen or so similar buildings ranged from about 1700–2700 f/m3 and lasted one or two years.
  • Buildings used without ACM destruction or after product impregnation maintained low asbestos contamination of < 300 f/m3 for more than 10–20 years.
  • In the author’s measurements, normal use and small local damage in occupied buildings generally stayed around < 300 f/m3, with a reported maximum of 560 f/m3; more extensive disturbance/removal was associated with 2000–6000 f/m3 or more in affected zones.

## Methods

  • Comparative field study of typical old German building types in Poland, especially “BERLIN” and “LIPSK”, plus a demolition case (“MOA”), observed across different stages: normal use, preservation/protection, renovation damage, asbestos removal, and demolition.
  • Air sampling of respirable asbestos fibers using static and dynamic sampling; filters were analyzed by PCM + PLM and some tests by SEM–EDS, following ISO-based procedures.
  • The study examined buildings and air samples in Poland over 2002–2022; analysis focused on fiber concentrations in rooms and in areas distant from work zones, with comparisons over time.

## Limitations

  • The paper states that outdoor air, large-volume rooms, badly damaged buildings, and short-interval repeat tests show large dispersion; results should be treated as approximate.
  • It also states that only chrysotile was identified in material samples and air samples, so the findings may not generalize to other asbestos types.
  • Evident from the text: the study is based on selected buildings and area measurements with time lag from the works, so it cannot provide a universally fixed asbestos concentration for all buildings or a direct causal estimate of health risk.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1038/s41598-023-37257-z

Cites

35 of 35 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Figure 1 The tested buildings. Figure: (a) and (b) Typical “BERLIN” building, general view before renovation (Poland, Warsaw), (c) Current view of building type “BERLIN” no. 2 after correct renovation (enclosure and encapsulation) (Poland, Olsztyn), Buildings type “LIPSK” in Poland, Warsaw: (d) Building type “LIPSK” after similar renovation as building type “BERLIN” no. 2, (e) Poland, Warsaw, Complex of two connected buildings of type “LIPSK”, on the left, building no. 11 (red), on the left side, building no. 7 (white) on the right side, (f) Poland, Warsaw, Buildings type “LIPSK” after asbestos removal and change of façade. Inside, on the left – “LIPSK” without any modification, removalor replacement of construction products. Typical damages of “SOKALIT” are shown in Supplementary Information 1 and 2.
Figure 1 The tested buildings. Figure: (a) and (b) Typical “BERLIN” building, general view before renovation (Poland, Warsaw), (c) Current view of building type “BERLIN” no. 2 after correct renovation (enclosure and encapsulation) (Poland, Olsztyn), Buildings type “LIPSK” in Poland, Warsaw: (d) Building type “LIPSK” after similar renovation as building type “BERLIN” no. 2, (e) Poland, Warsaw, Complex of two connected buildings of type “LIPSK”, on the left, building no. 11 (red), on the left side, building no. 7 (white) on the right side, (f) Poland, Warsaw, Buildings type “LIPSK” after asbestos removal and change of façade. Inside, on the left – “LIPSK” without any modification, removalor replacement of construction products. Typical damages of “SOKALIT” are shown in Supplementary Information 1 and 2.CC BY · PubMed Central
Figure 2 Comparison of airborne asbestos concentration in building types “BERLIN” and MOA – during demolition. The dashed white line corresponds to changes in pollution with the complete demolition of the MOA building. The navy blue line shows changes in indoor air pollution in the “BERLIN” type building after improper renovation, which led to damage to ACM products. The measurement was carried out up to 144 weeks from the moment of suspension of works. Only the last measurement reached the level of pollution that analogous buildings had without asbestos removal. The rectangle with a pink filling shows the values measured in this building 16 weeks after the renovation was discontinued. The rectangle with a green filling, 4 examples of asbestos dust concentration values in buildings of the same type (“BERLIN”), in which asbestos has not been dismantled, are circled. Markings: orange and brown colors correspond to the building before ACM was treated with impregnating agents. Blue and green colors with a lighter and darker shade - buildings after applying the impregnating agent. Red color - building without renovation in good technical condition. In the figure, the horizontal segments represent the average value of the concentration of asbestos dust in the building, the circles - the single values in the rooms exceeding the average value.
Figure 2 Comparison of airborne asbestos concentration in building types “BERLIN” and MOA – during demolition. The dashed white line corresponds to changes in pollution with the complete demolition of the MOA building. The navy blue line shows changes in indoor air pollution in the “BERLIN” type building after improper renovation, which led to damage to ACM products. The measurement was carried out up to 144 weeks from the moment of suspension of works. Only the last measurement reached the level of pollution that analogous buildings had without asbestos removal. The rectangle with a pink filling shows the values measured in this building 16 weeks after the renovation was discontinued. The rectangle with a green filling, 4 examples of asbestos dust concentration values in buildings of the same type (“BERLIN”), in which asbestos has not been dismantled, are circled. Markings: orange and brown colors correspond to the building before ACM was treated with impregnating agents. Blue and green colors with a lighter and darker shade - buildings after applying the impregnating agent. Red color - building without renovation in good technical condition. In the figure, the horizontal segments represent the average value of the concentration of asbestos dust in the building, the circles - the single values in the rooms exceeding the average value.CC BY · PubMed Central
Figure 3 Building no. 1 After 2 weeks of the wrong renovation: Renovated rooms after prolonged intensive ventilation. Rooms with damaged ACM-s, not renovated, in use. Renovated rooms not in use. Renovated rooms, normally used from two weeks to three years after completion of work. The trend of contamination changes. Building type “MOA” no. 11 During the wrong demolition: Single measured result in the average room. The trend of changes in pollution. Building “BERLIN” no. 2 A properly renovated and the others, without renovation, nos. 3, 4, 5, 3a and 4a: Average air analysis results for the entire building in 2002 (before renovation). Use without ACM restrictions. Apartment No 19. Average air analysis results for the entire building in 2006 (1 year after renovation). Apartment no. 19. Average air analysis results for the entire building in 2015 (10 years after renovation). Apartment No 19. Analysis containing the premises in which the owner, after renovation, in 2006 rearranged the internal walls on his own (in Table 3 these are the values of 1300 and 1800 f/m3). Average air analysis results for the entire building in 2022 measured results in average room analyzed in optical microscopy and SEM—EDS method (10 measurements). Buildings type “BERLIN” no. 3, 4, 5—not renovated, good condition of ACM. Average air analysis. Buildings type “BERLIN” no. 3a, 4a,—not renovated, different condition of ACM, local minor damage. Average air analysis. Average pollution in rooms with the greatest usable damage of external walls. Buildings “LIPSK” nos. 6 – 11: Building type “LIPSK” no. 6, average air analysis results after correct preservation of ACM-s. Building type “LIPSK” no. 8–10, average air analysis results outside of leaky work zones during asbestos removal in these zones. Building type “LIPSK” no. 11, average air analysis result in rooms during asbestos removal in building no 7. Both buildings are connected and were separated during renovation. Building type “LIPSK” no. 7, average air analysis result in rooms, 10 month after finished asbestos removal and final cleaning of all the building.
Figure 3 Building no. 1 After 2 weeks of the wrong renovation: Renovated rooms after prolonged intensive ventilation. Rooms with damaged ACM-s, not renovated, in use. Renovated rooms not in use. Renovated rooms, normally used from two weeks to three years after completion of work. The trend of contamination changes. Building type “MOA” no. 11 During the wrong demolition: Single measured result in the average room. The trend of changes in pollution. Building “BERLIN” no. 2 A properly renovated and the others, without renovation, nos. 3, 4, 5, 3a and 4a: Average air analysis results for the entire building in 2002 (before renovation). Use without ACM restrictions. Apartment No 19. Average air analysis results for the entire building in 2006 (1 year after renovation). Apartment no. 19. Average air analysis results for the entire building in 2015 (10 years after renovation). Apartment No 19. Analysis containing the premises in which the owner, after renovation, in 2006 rearranged the internal walls on his own (in Table 3 these are the values of 1300 and 1800 f/m3). Average air analysis results for the entire building in 2022 measured results in average room analyzed in optical microscopy and SEM—EDS method (10 measurements). Buildings type “BERLIN” no. 3, 4, 5—not renovated, good condition of ACM. Average air analysis. Buildings type “BERLIN” no. 3a, 4a,—not renovated, different condition of ACM, local minor damage. Average air analysis. Average pollution in rooms with the greatest usable damage of external walls. Buildings “LIPSK” nos. 6 – 11: Building type “LIPSK” no. 6, average air analysis results after correct preservation of ACM-s. Building type “LIPSK” no. 8–10, average air analysis results outside of leaky work zones during asbestos removal in these zones. Building type “LIPSK” no. 11, average air analysis result in rooms during asbestos removal in building no 7. Both buildings are connected and were separated during renovation. Building type “LIPSK” no. 7, average air analysis result in rooms, 10 month after finished asbestos removal and final cleaning of all the building.CC BY · PubMed Central
Figure 4 (a) Trend of changes in Building no. 1 over time. The X-axis is the elapsed time [in weeks], and the Y-axis is the concentration of respirable asbestos fibres [f/m3]. (b) Trend of changes in Building no. 2 over time. The X-axis is the elapsed time [in weeks], and the Y-axis is the concentration of respirable asbestos fibres [f/m3].
Figure 4 (a) Trend of changes in Building no. 1 over time. The X-axis is the elapsed time [in weeks], and the Y-axis is the concentration of respirable asbestos fibres [f/m3]. (b) Trend of changes in Building no. 2 over time. The X-axis is the elapsed time [in weeks], and the Y-axis is the concentration of respirable asbestos fibres [f/m3].CC BY · PubMed Central
Figure 5 Changes in concentration of internal air pollution in “LIPSK” buildings during use and asbestos removal. Comparison of three buildings over a 40-week period. Filled diamond Asbestos dismantling. The increase in indoor air pollution after the work (after the 10th week) was caused by the drying of the walls. Filled square Normal room operation and Filled triangle Normal room operation (with standard operational ACM damage. After the tenth week from the start of the research, measures limiting the destruction of products and dust emission were introduced in the use of the buildings).
Figure 5 Changes in concentration of internal air pollution in “LIPSK” buildings during use and asbestos removal. Comparison of three buildings over a 40-week period. Filled diamond Asbestos dismantling. The increase in indoor air pollution after the work (after the 10th week) was caused by the drying of the walls. Filled square Normal room operation and Filled triangle Normal room operation (with standard operational ACM damage. After the tenth week from the start of the research, measures limiting the destruction of products and dust emission were introduced in the use of the buildings).CC BY · PubMed Central
Figure 6 Estimated balance of asbestos-borne changes in rooms outside the work zones of “LIPSK” and “BERLIN” buildings subject to the asbestos removal process, taking into account routine execution errors.
Figure 6 Estimated balance of asbestos-borne changes in rooms outside the work zones of “LIPSK” and “BERLIN” buildings subject to the asbestos removal process, taking into account routine execution errors.CC BY · PubMed Central

Verification

Claims the paper makes

3 Valid · 5 Not valid · 6 Not checked · 29 Own results and interpretations

22 more claims

Create a free account to see all 43 claims and every source verdict.

See all claims — free account
  • Probably not a substantial claim. 10
  • It may state two separate claims as one. 9

Create a free account to see these claims.

Citations

Cites

Show all 35 references

Research works printed but not linked: 2

  1. Al-Sareji, O. J., Grmasha, R. A., Salman, J. M. & Hashim, K. S. Street dust contamination by heavy metals in Babylon governorate, Iraq. J. Eng. Sci. Technol. 16(1), 455–469 (2021).
  2. Upton, A. C. Asbestos in Public and Commercial Buildings - A literature revive and synthesis of current knowledge, Health Effect Institute - Asbestos Research. Cambridge (1991) https://www.healtheffects.org/publication/asbestos-public-and-commercial-buildings.

Cited by

See all 4

Metadata

Authors
Obmiński, A.
Affiliations
Instytut Techniki Budowlanej (PL)
Corresponding author
Obmiński, Andrzej
Venue
Scientific Reports
Published
2023-08-21
Volume
13
Issue
1
Pages
13577-13577
ISSN
2045-2322 (ISSN-L)
OpenAlex
W4386027889
Cited by
4
References
35
Citations by year
2025: 3 · 2024: 1
FWCI
0.73
Type
journal article
Language
en
Open access
Licence
Locations
  • Scientific Reports (publishedVersion, cc-by)
  • Research Square (acceptedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
Topics
  • Health Sciences › Medicine › Pulmonary and Respiratory Medicine › Occupational and environmental lung diseases
  • Physical Sciences › Environmental Science › Health, Toxicology and Mutagenesis › Indoor Air Quality and Microbial Exposure
  • Health Sciences › Medicine › Public Health, Environmental and Occupational Health › Occupational Health and Safety in Workplaces
Keywords
asbestos-containing materials, asbestos removal, building renovation, office buildings, occupant exposure, ventilation

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-10-01, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-01 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Cited sources are checked with a language model’s help (gpt-6-sol).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Comparison of the effects of use, protection, improper renovation and removal of asbestos products on the example of typical old office buildings in Poland. https://app.cochat.ai/papers/10.1038/s41598-023-37257-z
The paper
Obmiński, A. (2023). Comparison of the effects of use, protection, improper renovation and removal of asbestos products on the example of typical old office buildings in Poland. Scientific Reports. https://doi.org/10.1038/s41598-023-37257-z

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.