The DOI matches its Crossref record; 21 of the 21 references it cites were found in a registry or an index.
Evolution of solidification texture during additive manufacturing
Open accessAbstract
Striking differences in the solidification textures of a nickel based alloy owing to changes in laser scanning pattern during additive manufacturing are examined based on theory and experimental data. Understanding and controlling texture are important because it affects mechanical and chemical properties. Solidification texture depends on the local heat flow directions and competitive grain growth in one of the six <100> preferred growth directions in face centered cubic alloys. Therefore, the heat flow directions are examined for various laser beam scanning patterns based on numerical modeling of heat transfer and fluid flow in three dimensions. Here we show that numerical modeling can not only provide a deeper understanding of the solidification growth patterns during the additive manufacturing, it also serves as a basis for customizing solidification textures which are important for properties and performance of components.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
3D bioprinting of tissues and organs
Murphy, S. V., & Atala, A. (2014) · Nature Biotechnology · doi:10.1038/nbt.2958 · Cited by 7,034
Rapid casting of patterned vascular networks for perfusable engineered three-dimensional tissues
Miller, J. S., Stevens, K. R., Yang, M. T., Baker, B. M., Nguyen, D.-H. T., Cohen, D. M., Toro, E., Chen, A. A., Galie, P. A., Yu, X., et al. (2012) · Nature Materials · doi:10.1038/nmat3357 · Cited by 1,917
Carroll, B. E., Palmer, T. A., & Beese, A. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.12.054 · Cited by 1,507
Xu, W., Brandt, M., Sun, S., Elambasseril, J., Liu, Q., Latham, K., Xia, K., & Qian, M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.11.028 · Cited by 1,245
Additive manufacturing of tissues and organs
Melchels, F. P. W., Domingos, M. A. N., Klein, T. J., Malda, J., Bartolo, P. J., & Hutmacher, D. W. (2012) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2011.11.007 · Cited by 1,213
Jia, Q., & Gu, D. (2014) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2013.09.171 · Cited by 905
Dinda, G. P., Dasgupta, A. K., & Mazumder, J. (2009) · Materials Science and Engineering: A · doi:10.1016/j.msea.2009.01.009 · Cited by 858
Self-citationYan, C., Hao, L., Hussein, A., Young, P., & Raymont, D. (2014) · Materials & Design · doi:10.1016/j.matdes.2013.10.027 · Cited by 622
Physical processes in fusion welding
DebRoy, T., & David, S. A. (1995) · Reviews of Modern Physics · doi:10.1103/revmodphys.67.85 · Cited by 559
Self-citationTexture control during laser deposition of nickel-based superalloy
Dinda, G. P., Dasgupta, A. K., & Mazumder, J. (2012) · Scripta Materialia · doi:10.1016/j.scriptamat.2012.06.014 · Cited by 451
Self-citationDirect Desktop Printed-Circuits-on-Paper Flexible Electronics
Zheng, Y., He, Z., Gao, Y., & Liu, J. (2013) · Scientific Reports · doi:10.1038/srep01786 · Cited by 370
Heat transfer and material flow during laser assisted multi-layer additive manufacturing
Manvatkar, V., De, A., & DebRoy, T. (2014) · Journal of Applied Physics · doi:10.1063/1.4896751 · Cited by 338
Self-citationDeveloping Gradient Metal Alloys through Radial Deposition Additive Manufacturing
Hofmann, D. C., Roberts, S., Otis, R., Kolodziejska, J., Dillon, R. P., Suh, J.-O., Shapiro, A. A., Liu, Z.-K., & Borgonia, J.-P. (2014) · Scientific Reports · doi:10.1038/srep05357 · Cited by 314
Manvatkar, V., De, A., & DebRoy, T. (2015) · Materials Science and Technology · doi:10.1179/1743284714y.0000000701 · Cited by 282
Self-citationCurrent Issues and Problems in Welding Science
David, S. A., & DebRoy, T. (1992) · Science · doi:10.1126/science.257.5069.497 · Cited by 270
Self-citationCompositionally graded metals: A new frontier of additive manufacturing
Hofmann, D. C., Kolodziejska, J., Roberts, S., Otis, R., Dillon, R. P., Suh, J.-O., Liu, Z.-K., & Borgonia, J.-P. (2014) · Journal of Materials Research · doi:10.1557/jmr.2014.208 · Cited by 255
Fabrication of low cost soft tissue prostheses with the desktop 3D printer
He, Y., Xue, G.-H., & Fu, J.-Z. (2014) · Scientific Reports · doi:10.1038/srep06973 · Cited by 243
Liu, Z., & Qi, H. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.12.046 · Cited by 147
Oxide films in laser additive manufactured Inconel 718
Zhang, Y. N., Cao, X. J., Wanjara, P., et al. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.07.039 · Cited by 125
Solidification Map of a Nickel-Base Alloy
Blecher, J. J., Palmer, T. A., & DebRoy, T. (2013) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-013-2149-1 · Cited by 91
Self-citationLiu, Z., & Qi, H. (2014) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-013-2178-9 · Cited by 57
Cited by
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Self-citationLi, Y., Feng, Z., Hao, L., Huang, L., Xin, C., Wang, Y., Bilotti, E., Essa, K., Zhang, H., Li, Z., et al. (2020) · Advanced Materials Technologies · doi:10.1002/admt.201900981 · Cited by 614
Mostafaei, A., Ghiaasiaan, R., Ho, I.-T., Strayer, S., Chang, K.-C., Shamsaei, N., Shao, S., Paul, S., Yeh, A.-C., Tin, S., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2023.101108 · Cited by 531
Mechanistic models for additive manufacturing of metallic components
Wei, H. L., Mukherjee, T., Zhang, W., Zuback, J. S., Knapp, G. L., De, A., & DebRoy, T. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100703 · Cited by 530
Self-citationPrintability of alloys for additive manufacturing
Mukherjee, T., Zuback, J. S., De, A., & DebRoy, T. (2016) · Scientific Reports · doi:10.1038/srep19717 · Cited by 523
Self-citation
Metadata
- Authors
- Wei, H. L., Mazumder, J., & DebRoy, T.
- Venue
- Scientific Reports
- Published
- 2015-11-10
- Volume
- 5
- Issue
- 1
- Pages
- 16446-16446
- ISSN
- 2045-2322 (ISSN-L)
- OpenAlex
- W2408860057
- Cited by
- 557
- References
- 21
- FWCI
- 23.21
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.