The DOI matches its Crossref record; 41 of the 41 references it cites were found in a registry or an index.
Inkjet printing of organic electronics – comparison of deposition techniques and state-of-the-art developments
Open accessAbstract
Inkjet printing represents a solution dispensing technique that is characterized by its non-contact, material-efficient and reproducible processing. This critical review discusses the use of inkjet printing for organic electronics with a focus on the applicability as well as the drying behavior. The nascent inkjet printing technique is compared to commonly used solution deposition methods, like spin-coating and doctor blading. Basic drying principles of inkjet printed features are understood and fundamental correlations between processing properties and film characteristics can be drawn. It is, however, a long way to gain a full understanding of the complete drying process, since the process conditions as well as the ink properties correlate in a complex relation with the final device properties. Nevertheless, inkjet printing has the potential to evolve as one of the most promising film preparation techniques in the future and has already been applied successfully in combinatorial screening workflows and for the preparation of organic solar cell devices.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Conjugated Polymer-Based Organic Solar Cells
Günes, S., Neugebauer, H., & Sariciftci, N. S. (2007) · Chemical Reviews · doi:10.1021/cr050149z · Cited by 6,279
Li, G., Shrotriya, V., Huang, J., Yao, Y., Moriarty, T., Emery, K., & Yang, Y. (2005) · Nature Materials · doi:10.1038/nmat1500 · Cited by 5,535
Design Rules for Donors in Bulk‐Heterojunction Solar Cells—Towards 10 % Energy‐Conversion Efficiency
Scharber, M. C., Mühlbacher, D., Koppe, M., Denk, P., Waldauf, C., Heeger, A. J., & Brabec, C. J. (2006) · Advanced Materials · doi:10.1002/adma.200501717 · Cited by 5,205
Liang, Y., Xu, Z., Xia, J., Tsai, S., Wu, Y., Li, G., Ray, C., & Yu, L. (2010) · Advanced Materials · doi:10.1002/adma.200903528 · Cited by 3,649
Fabrication and processing of polymer solar cells: A review of printing and coating techniques
Krebs, F. C. (2009) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2008.10.004 · Cited by 3,260
Derby, B. (2010) · Annual Review of Materials Research · doi:10.1146/annurev-matsci-070909-104502 · Cited by 1,984
Inkjet Printing of Polymers: State of the Art and Future Developments
de Gans, B. ‐., Duineveld, P. C., & Schubert, U. S. (2004) · Advanced Materials · doi:10.1002/adma.200300385 · Cited by 1,906
Self-citationMarangoni Effect Reverses Coffee-Ring Depositions
Hu, H., & Larson, R. G. (2006) · The Journal of Physical Chemistry B · doi:10.1021/jp0609232 · Cited by 1,645
Tandem polymer solar cells featuring a spectrally matched low-bandgap polymer
Dou, L., You, J., Yang, J., Chen, C.-C., He, Y., Murase, S., Moriarty, T., Emery, K., Li, G., & Yang, Y. (2012) · Nature Photonics · doi:10.1038/nphoton.2011.356 · Cited by 1,416
Stability of Polymer Solar Cells
Jørgensen, M., Norrman, K., Gevorgyan, S. A., Tromholt, T., Andreasen, B., & Krebs, F. C. (2012) · Advanced Materials · doi:10.1002/adma.201104187 · Cited by 1,366
Pattern formation in drying drops
Deegan, R. D. (2000) · Physical Review E · doi:10.1103/physreve.61.475 · Cited by 1,297
P3HT:PCBM, Best Seller in Polymer Photovoltaic Research
Dang, M. T., Hirsch, L., & Wantz, G. (2011) · Advanced Materials · doi:10.1002/adma.201100792 · Cited by 1,261
Chang, J.-F., Sun, B., Breiby, D. W., Nielsen, M. M., Sölling, T. I., Giles, M., McCulloch, I., & Sirringhaus, H. (2004) · Chemistry of Materials · doi:10.1021/cm049617w · Cited by 944
Krebs, F. C., Jørgensen, M., Norrman, K., Hagemann, O., Alstrup, J., Nielsen, T. D., Fyenbo, J., Larsen, K., & Kristensen, J. (2009) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2008.12.001 · Cited by 808
Inkjet printing as a deposition and patterning tool for polymers and inorganic particles
Tekin, E., Smith, P. J., & Schubert, U. S. (2008) · Soft Matter · doi:10.1039/b711984d · Cited by 807
Self-citationInfluence of Fluid Physical Properties on Ink-Jet Printability
Jang, D., Kim, D., & Moon, J. (2009) · Langmuir · doi:10.1021/la900059m · Cited by 745
Perelaer, J., Smith, P. J., Mager, D., Soltman, D., Volkman, S. K., Subramanian, V., Korvink, J. G., & Schubert, U. S. (2010) · Journal of Materials Chemistry · doi:10.1039/c0jm00264j · Cited by 736
Self-citationKrebs, F. C. (2009) · Organic Electronics · doi:10.1016/j.orgel.2009.03.009 · Cited by 608
Numerical Calculation of the Fluid Dynamics of Drop-on-Demand Jets
Fromm, J. E. (1984) · IBM Journal of Research and Development · doi:10.1147/rd.283.0322 · Cited by 601
Yang, H., Shin, T. J., Yang, L., Cho, K., Ryu, C. Y., & Bao, Z. (2005) · Advanced Functional Materials · doi:10.1002/adfm.200400297 · Cited by 570
Spin coating of thin and ultrathin polymer films
Hall, D. B., Underhill, P., & Torkelson, J. M. (1998) · Polymer Engineering & Science · doi:10.1002/pen.10373 · Cited by 545
Dennler, G., Scharber, M. C., Ameri, T., Denk, P., Forberich, K., Waldauf, C., & Brabec, C. J. (2008) · Advanced Materials · doi:10.1002/adma.200702337 · Cited by 529
Fabrication of bulk heterojunction plastic solar cells by screen printing
Shaheen, S. E., Radspinner, R., Peyghambarian, N., & Jabbour, G. E. (2001) · Applied Physics Letters · doi:10.1063/1.1413501 · Cited by 479
Printing Highly Efficient Organic Solar Cells
Hoth, C. N., Schilinsky, P., Choulis, S. A., & Brabec, C. J. (2008) · Nano Letters · doi:10.1021/nl801365k · Cited by 459
The Role of Processing in the Fabrication and Optimization of Plastic Solar Cells
Peet, J., Senatore, M. L., Heeger, A. J., & Bazan, G. C. (2009) · Advanced Materials · doi:10.1002/adma.200802559 · Cited by 391
Arias, A. C., MacKenzie, J. D., Stevenson, R., Halls, J. J. M., Inbasekaran, M., Woo, E. P., Richards, D., & Friend, R. H. (2001) · Macromolecules · doi:10.1021/ma010240e · Cited by 383
Flexible organic P3HT:PCBM bulk-heterojunction modules with more than 1 year outdoor lifetime
Hauch, J. A., Schilinsky, P., Choulis, S. A., Childers, R., Biele, M., & Brabec, C. J. (2008) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2008.01.004 · Cited by 373
Polymer based organic solar cells using ink-jet printed active layers
Aernouts, T., Aleksandrov, T., Girotto, C., Genoe, J., & Poortmans, J. (2008) · Applied Physics Letters · doi:10.1063/1.2833185 · Cited by 292
Variations in Semiconducting Polymer Microstructure and Hole Mobility with Spin-Coating Speed
DeLongchamp, D. M., Vogel, B. M., Jung, Y., Gurau, M. C., Richter, C. A., Kirillov, O. A., Obrzut, J., Fischer, D. A., Sambasivan, S., Richter, L. J., et al. (2005) · Chemistry of Materials · doi:10.1021/cm0513637 · Cited by 243
Ink‐Jet Printing of Wax‐Based Alumina Suspensions
Seerden, K. A. M., Reis, N., Evans, J. R. G., Grant, P. S., Halloran, J. W., & Derby, B. (2001) · Journal of the American Ceramic Society · doi:10.1111/j.1151-2916.2001.tb01045.x · Cited by 237
Mihailetchi, V. D., Xie, H., de Boer, B., Popescu, L. M., Hummelen, J. C., Blom, P. W. M., & Koster, L. J. A. (2006) · Applied Physics Letters · doi:10.1063/1.2212058 · Cited by 235
Eom, S. H., Park, H., Mujawar, S. H., Yoon, S. C., Kim, S.-S., Na, S.-I., Kang, S.-J., Khim, D., Kim, D.-Y., & Lee, S.-H. (2010) · Organic Electronics · doi:10.1016/j.orgel.2010.06.007 · Cited by 162
Pivrikas, A., Neugebauer, H., & Sariçiftçi, N. S. (2010) · Solar Energy · doi:10.1016/j.solener.2010.10.012 · Cited by 140
Wang, T., Dunbar, A. D. F., Staniec, P. A., Pearson, A. J., Hopkinson, P. E., Macdonald, J. E., Lilliu, S., Pizzey, C. L., Terrill, N. J., Donald, A. M., et al. (2010) · Soft Matter · doi:10.1039/c0sm00343c · Cited by 131
Combinatorial Screening of Polymer:Fullerene Blends for Organic Solar Cells by Inkjet Printing
Teichler, A., Eckardt, R., Hoeppener, S., Friebe, C., Perelaer, J., Senes, A., Morana, M., Brabec, C. J., & Schubert, U. S. (2010) · Advanced Energy Materials · doi:10.1002/aenm.201000027 · Cited by 108
Self-citationPark, C., Fleetham, T. A., Li, J., & Vogt, B. D. (2011) · Organic Electronics · doi:10.1016/j.orgel.2011.05.020 · Cited by 102
Film thickness dependency of the emission colors of PPE–PPVs in inkjet printed libraries
Tekin, E., Wijlaars, H., Holder, E., Egbe, D. A. M., & Schubert, U. S. (2006) · Journal of Materials Chemistry · doi:10.1039/b610996a · Cited by 77
Self-citationSchmidt‐Hansberg, B., Sanyal, M., Grossiord, N., Galagan, Y., Baunach, M., Klein, M. F. G., Colsmann, A., Scharfer, P., Lemmer, U., Dosch, H., et al. (2011) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2011.09.059 · Cited by 72
Lange, A., Wegener, M., Boeffel, C., Fischer, B., Wedel, A., & Neher, D. (2010) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2010.05.054 · Cited by 70
Verkouteren, R. M., & Verkouteren, J. R. (2011) · Langmuir · doi:10.1021/la201728f · Cited by 62
Inkjet-printed polymer–fullerene blends for organic electronic applications
Neophytou, M., Cambarau, W., Hermerschmidt, F., et al. (2012) · Microelectronic Engineering · doi:10.1016/j.mee.2012.02.005 · Cited by 27
Cited by
Wadsworth, A., Moser, M., Marks, A., Little, M. S., Gasparini, N., Brabec, C. J., Baran, D., & McCulloch, I. (2019) · Chemical Society Reviews · doi:10.1039/c7cs00892a · Cited by 986
Shape memory polymers: Past, present and future developments
Hager, M. D., Bode, S., Weber, C., & Schubert, U. S. (2015) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2015.04.002 · Cited by 950
Self-citationConductive Nanomaterials for Printed Electronics
Kamyshny, A., & Magdassi, S. (2014) · Small · doi:10.1002/smll.201303000 · Cited by 911
Materials that couple sensing, actuation, computation, and communication
McEvoy, M. A., & Correll, N. (2015) · Science · doi:10.1126/science.1261689 · Cited by 650
Paper‐Based Inkjet‐Printed Microfluidic Analytical Devices
Yamada, K., Henares, T. G., Suzuki, K., & Citterio, D. (2015) · Angewandte Chemie International Edition · doi:10.1002/anie.201411508 · Cited by 501
Metadata
- Authors
- Teichler, A., Perelaer, J., & Schubert, U. S.
- Venue
- Journal of Materials Chemistry C
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2013
- Volume
- 1
- Issue
- 10
- Pages
- 1910
- ISSN
- 2050-7526 (ISSN-L)
- 2050-7534
- OpenAlex
- W1972452697
- Cited by
- 271
- References
- 41
- FWCI
- 12.21
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.