CoChat

Strength Prediction of Mass-Timber Panel Concrete-Composite Connection with Inclined Screws and a Gap

Mirdad, Md Abdul Hamid, Chui, Ying Hei · 2020 · Journal of Structural Engineering

The DOI matches its Crossref record; 17 of the 17 references it cites were found in a registry or an index.

Abstract

Mass timber panels (MTPs) are a new generation of engineered wood panels that are available in large plane dimensions to facilitate fast floor construction with the obvious environmental benefit of being from a renewable material. In floor construction, concrete slab or topping is often applied over the MTPs to improve various performance attributes, including structural, acoustic, and vibration serviceability. A mass timber panel-concrete (MTPC) composite floor system often consists of a MTP connected to the concrete layer with mechanical fasteners and a sound insulation layer in between. The capacity of this type of composite system mostly depends on the strength of the connection, and often tests are performed to characterize connection properties required for structural design. In lieu of testing, analytical models can be developed to calculate connection properties based on component properties. To that end, two analytical models were developed for solid and layered timber by characterizing all possible kinematical failure modes for directly predicting the strength of a connection with inclined screws and an insulation layer. According to Johansen’s yield theory, the strength of a laterally loaded connection is controlled by the dowel-bearing effect of the fastener in timber, but joints with an inclined screw have a more complex behavior because of the combined bearing and withdrawal action of the screw. In the developed models, both the dowel-bearing and withdrawal action of the screw are considered along with the bending capacity of the screw and friction between the members. Both models were experimentally validated with a wide range of material properties. It was found that the models are capable of predicting the mode of failure of a connection and the load-carrying capacity within 10% of the experimental value.

Overview

Integrity signals

Registry

Crossref · 10.1061/(asce)st.1943-541x.0002678

Cites

17 of 17 references verified0 citation errors · 0 not checkable

Statistics

Recomputing p-values needs the paper’s full text.

Verification

Claims the paper makes

This paper’s full text isn’t openly available, so its claims and self-check weren’t run. The registry and citation checks still apply.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Citations

Cites

Show all 17 references

Research works printed but not linked: 5

  1. Bejtka I. and H. Blass. 2002. “Joints with inclined screws.” In Proc. Meeting 35 Int. Council for Building Research Studies and Documentation CIB W18—Timber Structures. Timber Structures Universtität Karlsruhe Karlsruhe Germany.
  2. Blass, H., I. Bejtka, and T. Uibel. 2006. Trägfähigkeit von verbindung mit selbst bohrenden holzschrauben mit vollgewinde. Lehrstuhl für ingenieurholzbau und baukonstruktionen. Karlsruhe, Germany: Universität Karlsruhe.
  3. Kennedy S. 2014. “Withdrawal and embedding resistance of fasteners in timber and CLT panels.” M.Sc. thesis Dept. of Forestry Laval Univ.
  4. Kevarinmäki A. 2002. “Joints with inclined screws.” In Proc. CIB-W18 Timber Structures Meeting Paper 35-7-4. Karlsruhe Germany: Universtität Karlsruhe.
  5. Shirvani, M. 1998. “Statistical analysis and design recommendations.” In Behavior of tensile anchors in concrete, 261–271. Austin, TX: Univ. of Texas at Austin.

Cited by

See all 24

Metadata

Authors
Mirdad, M. A. H., & Chui, Y. H.
Affiliations
  • University of Alberta (CA)
  • Natural Sciences and Engineering Research Council of Canada (CA)
Corresponding author
Mirdad, Md Abdul Hamid
Venue
Journal of Structural Engineering
Published
2020-08
Volume
146
Issue
8
ISSN
  • 0733-9445 (ISSN-L)
  • 1943-541X
OpenAlex
W3024424385
Cited by
24
References
17
Citations by year
2026: 1 · 2025: 3 · 2024: 4 · 2023: 4 · 2022: 5 · 2021: 5 · 2020: 2
FWCI
2.34
Type
journal article
Language
en
Open access
closed
Locations
Journal of Structural Engineering (publishedVersion)
Topics
  • Physical Sciences › Engineering › Civil and Structural Engineering › Structural Load-Bearing Analysis
  • Physical Sciences › Engineering › Building and Construction › Wood Treatment and Properties
  • Life Sciences › Agricultural and Biological Sciences › Plant Science › Bamboo properties and applications
Keywords
floor construction, failure modes

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Strength Prediction of Mass-Timber Panel Concrete-Composite Connection with Inclined Screws and a Gap. https://app.cochat.ai/papers/10.1061/(asce)st.1943-541x.0002678
The paper
Mirdad, M. A. H., & Chui, Y. H. (2020). Strength Prediction of Mass-Timber Panel Concrete-Composite Connection with Inclined Screws and a Gap. Journal of Structural Engineering. https://doi.org/10.1061/(asce)st.1943-541x.0002678

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.