The DOI matches its Crossref record; 21 of the 21 references it cites were found in a registry or an index.
State of the Art of High Heat Flux Cooling Technologies
Open accessAbstract
The purpose of this literature review is to compare different cooling technologies currently in development in research laboratories that are competing to solve the challenge of cooling the next generation of high heat flux computer chips. Today, most development efforts are focused on three technologies: liquid cooling in copper or silicon micro-geometry heat dissipation elements, impingement of liquid jets directly on the silicon surface of the chip, and two-phase flow boiling in copper heat dissipation elements or plates with numerous microchannels. The principal challenge is to dissipate the high heat fluxes (current objective is 300 W/cm2) while maintaining the chip temperature below the targeted temperature of 85°C, while of second importance is how to predict the heat transfer coefficients and pressure drops of the cooling process. In this study, the state of the art of these three technologies from recent experimental articles (since 2003) is analyzed and a comparison of the respective merits and drawbacks of each technology is presented. The conclusion is that two-phase flow boiling in microchannels is the most promising approach; impingement cooling also has good prospects but single-phase liquid cooling is probably only a short-term solution. As an example of the state of the first technology, the Heat and Mass Transfer Laboratory at Ecole Polytechnique Fédérale de Lausanne has already achieved 200 W/cm2 of cooling in a first prototype, with a low pumping power, good temperature uniformity, and at the required maximal operating temperature.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
High-performance heat sinking for VLSI
Tuckerman, D. B., & Pease, R. F. W. (1981) · IEEE Electron Device Letters · doi:10.1109/edl.1981.25367 · Cited by 5,291
A simple friction pressure drop correlation for two-phase flow in pipes
Muller-Steinhagen, H. M. G., & Heck, K. (1986) · Chemical Engineering and Processing - Process Intensification · doi:10.1016/0255-2701(86)80008-3 · Cited by 1,057
Spray cooling heat transfer: The state of the art
Kim, J. (2007) · International Journal of Heat and Fluid Flow · doi:10.1016/j.ijheatfluidflow.2006.09.003 · Cited by 968
Metal foams as compact high performance heat exchangers
Boomsma, K., Poulikakos, D., & Zwick, F. (2003) · Mechanics of Materials · doi:10.1016/j.mechmat.2003.02.001 · Cited by 744
Heat transfer model for evaporation in microchannels. Part I: presentation of the model
Thome, J. R., Dupont, V., & Jacobi, A. M. (2004) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2004.01.006 · Cited by 686
Self-citationDhir, V. K. (1998) · Annual Review of Fluid Mechanics · doi:10.1146/annurev.fluid.30.1.365 · Cited by 662
Lee, J., & Mudawar, I. (2004) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2004.09.019 · Cited by 550
Lee, J., & Mudawar, I. (2004) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2004.09.018 · Cited by 300
Boiling heat transfer in rectangular microchannels with reentrant cavities
Koşar, A., Kuo, C.-J., & Peles, Y. (2005) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2005.06.003 · Cited by 295
Thermal–hydraulic performance of small scale micro-channel and porous-media heat-exchangers
Jiang, P.-X., Fan, M.-H., Si, G.-S., & Ren, Z.-P. (2001) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(00)00169-1 · Cited by 253
A Practical Implementation of Silicon Microchannel Coolers for High Power Chips
Colgan, E. G., Furman, B., Gaynes, M., Graham, W. S., LaBianca, N. C., Magerlein, J. H., Polastre, R. J., Rothwell, M. B., Bezama, R. J., Choudhary, R., et al. (2007) · IEEE Transactions on Components and Packaging Technologies · doi:10.1109/tcapt.2007.897977 · Cited by 252
Flow vaporization of CO2 in microchannel tubes
Pettersen, J. (2004) · Experimental Thermal and Fluid Science · doi:10.1016/s0894-1777(03)00029-3 · Cited by 227
Sintered porous medium heat sink for cooling of high-power mini-devices
Hetsroni, G., Gurevich, M., & Rozenblit, R. (2006) · International Journal of Heat and Fluid Flow · doi:10.1016/j.ijheatfluidflow.2005.08.005 · Cited by 189
Nano and Micro Technology-Based Next-Generation Package-Level Cooling Solutions
Prasher, R. (2005) · Intel Technology Journal · doi:10.1535/itj.0904.03 · Cited by 181
Single-phase liquid cooled microchannel heat sink for electronic packages
Zhang, H. Y., Pinjala, D., Wong, T. N., Toh, K. C., & Joshi, Y. K. (2005) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2004.09.014 · Cited by 181
Flow boiling and flow regimes in small diameter tubes
Huo, X., Chen, L., Tian, Y. S., & Karayiannis, T. G. (2004) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2003.11.027 · Cited by 168
Optimized Heat Transfer for High Power Electronic Cooling Using Arrays of Microjets
Fabbri, M., & Dhir, V. K. (2004) · ASME Journal of Heat and Mass Transfer · doi:10.1115/1.1924624 · Cited by 147
Self-citationVertical flow boiling of refrigerant R134a in small channels
Agostini, B., & Bontemps, A. (2004) · International Journal of Heat and Fluid Flow · doi:10.1016/j.ijheatfluidflow.2004.08.003 · Cited by 145
Self-citationA practical implementation of silicon microchannel coolers for high power chips
Colgan, E. G., Furman, B. K., Gaynes, M. A., Graham, W., LaBianca, N., Magerlein, J. H., Polastre, R. J., Rothwell, M. B., Bezama, R. J., Choudhary, R., et al. (2005) · Annual IEEE Semiconductor Thermal Measurement and Management Symposium/Proceedings · doi:10.1109/stherm.2005.1412151 · Cited by 106
Meso Scale Pulsating Jets for Electronics Cooling
Garg, J., Arık, M., Weaver, S. E., Wetzel, T. G., & Saddoughi, S. G. (2005) · Journal of Electronic Packaging · doi:10.1115/1.2065727 · Cited by 78
Peters, K. H., & Kulacki, F. A. (2005) · ASME Heat Transfer Summer Conference (HT) · doi:10.1115/ht2005-72036 · Cited by 6
Cited by
Co-designing electronics with microfluidics for more sustainable cooling
van Erp, R., Soleimanzadeh, R., Nela, L., Kampitsis, G., & Matioli, E. (2020) · Nature · doi:10.1038/s41586-020-2666-1 · Cited by 1,142
A critical review of traditional and emerging techniques and fluids for electronics cooling
Sohel Murshed, S. M., & Nieto de Castro, C. A. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.04.112 · Cited by 987
Towards hybrid nanofluids: Preparation, thermophysical properties, applications, and challenges
Babar, H., & Ali, H. M. (2019) · Journal of Molecular Liquids · doi:10.1016/j.molliq.2019.02.102 · Cited by 485
Kandlikar, S. G. (2012) · Journal of Heat Transfer · doi:10.1115/1.4005126 · Cited by 389
State-of-the-art in heat exchanger additive manufacturing
Kaur, I., & Singh, P. (2021) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2021.121600 · Cited by 319
Metadata
- Authors
- Agostini, B., Fabbri, M., Park, J. E., Wojtan, L., Thome, J. R., & Michel, B.
- Venue
- Heat Transfer Engineering
- Publisher
- Informa UK Limited
- Published
- 2007-04
- Volume
- 28
- Issue
- 4
- Pages
- 258-281
- ISSN
- 0145-7632 (ISSN-L)
- 1521-0537
- OpenAlex
- W2051986639
- Cited by
- 640
- References
- 21
- FWCI
- 43.74
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.