Effect of Ground Slope, Stump Diameter, and Species on Stump Height for Feller-Buncher and Chainsaw Felling
The DOI matches its Crossref record; 4 of the 4 references it cites were found in a registry or an index.
Abstract
Stump heights were measured on six clear-cut blocks in the central interior of British Columbia using a systematic sampling method. Felling method, ground slope, species and stump diameter were analyzed to determine their effect on stump height. Mechanized felling with a feller-buncher resulted in lower stumps by 5.5 cm on average than those from manual felling with a chainsaw. The wide range (9.6 cm to 23.4 cm) of the average stump heights sampled from six clear-cut units indicates that other factors such as slope, species and stump diameter may influence stump height. When considering tree species, the feller-buncher left lower stump heights for subalpine fir and white spruce, while chainsaw felling resulted in lower stumps for Douglas-fir. Average stump and feller-buncher stump heights tended to increase as percent slope increased up to 45%, but the opposite trend was found in chainsaw felled sites with slopes greater than 45%. Both feller-buncher and chainsaw felling methods resulted in lower stumps as the average stump diameter increased. On ground slopes less than 30% and stump diameters between 30 and 70 cm, our analysis suggested that feller-buncher felling resulted in lower stump heights than chainsaw felling. Chainsaw felling can cause stump-pulls, slabs, and unevenness at the bottom of the tree being felled, requiring a further reduction of wood that could potentially be used for solid wood products. Feller-buncher felling, however, results in greater wood volume waste as the result of a thicker saw blade kerf than does chainsaw felling.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“For slopes less than 30%, feller-buncher felling is recommended as a more efficient choice than chainsaw felling [77].”
From Life-cycle carbon footprint and total production potential of cross-laminated timber from California’s wildland-urban interface (2025) · cites this paper as [77]
Citations
Cites
Biometry: The Principles and Practice of Statistics in Biological Research
Sokal, R. R., & Rohlf, F. J. (1969) · Cited by 20,963
Costs and cost trends for forestry practices in the South
Watson, W. F., STRAKA, T. J., & Bullard, S. H. (1987) · Index of Texas Archaeology Open Access Grey Literature from the Lone Star State · Cited by 185
A Comparison of Felling Techniques on Stump Height and Log Damage with Economic Interpretations
Boston, K., & Dysart, G. (2000) · Western Journal of Applied Forestry · doi:10.1093/wjaf/15.2.59 · Cited by 19 · cited 6×
“Wood waste can be significant if we consider the accumulative effects of such poor logging practices occurring on many harvesting sites [2, 5].”
BackgroundInfluentialShaffer, R. M., & Taumas, R. S. (1992) · Southern Journal of Applied Forestry · doi:10.1093/sjaf/16.3.140 · Cited by 5 · cited 4×
“7 cm was also found in three mixed forests felled using continuous disk sawheads in Virginia [6].”
BackgroundInfluential
Research works printed but not linked: 3
- Dubois M., 1991, For. Farm. (Manual Ed.), 50, 26
- Hall R., 2004, West. J. Appl. For. for review, 19
- Murphy G., 1984, LIRA Tech. Release., 6, 6
Cited by
Schweier, J., Spinelli, R., Magagnotti, N., & Becker, G. (2014) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2014.11.013 · Cited by 53
Mirkala, S. R. M. (2009) · Dissertationes Forestales · doi:10.14214/df.82 · Cited by 40
“In felling trees with a chain saw, stumps should be as close to the ground as possible because the most valuable part of tree is its butt, additionally it should be cut at an angle to minimize hang-ups (Pavel 1999, Han and Renzie 2005). Felling needs to be carried out at a certain period of time (mainly in winter time…”
BackgroundMortality, re-sprouting vigor and physiology of coppice stumps after mechanized cutting
Spinelli, R., Pari, L., Aminti, G., Magagnotti, N., & Giovannelli, A. (2017) · Annals of Forest Science · doi:10.1007/s13595-016-0604-z · Cited by 34
“In any case, cutting height is likely affected by a combination of factors, including machine type, tree species, stump diameter, and slope gradient (Han and Renzie 2005).”
Eggers, J. R., McEwan, A., & Conradie, B. (2010) · Southern Forests a Journal of Forest Science · doi:10.2989/20702620.2010.481099 · Cited by 23
“Studies by Kewley and Kellogg (2001) and Han and Renzie (2005) showed that trees felled mechanically by a feller-buncher had a higher mean value recovery than trees that were felled manually.”
MethodCost production study of motor-manually felling and processing of logs.
Ghaffarian, M. R., & Sobhani, H. (2007) · USC Research Bank (University of the Sunshine Coast) · Cited by 16
Metadata
- Authors
- Han, H.-S., & Renzie, C.
- Affiliations
- University of Idaho (US)
- University of Northern British Columbia (CA)
- ORCID
- Han, Han-Sup
- Venue
- International Journal of Forest Engineering
- Publisher
- Informa UK Limited
- Published
- 2005-06
- Volume
- 16
- Issue
- 2
- Pages
- 81-88
- ISSN
- 1494-2119 (ISSN-L)
- 1913-2220
- OpenAlex
- W1543546893
- Cited by
- 28
- References
- 4
- Citations by year
- 2025: 2 · 2024: 1 · 2023: 2 · 2022: 1 · 2021: 1 · 2020: 4 · 2019: 1 · 2018: 2 · 2017: 5 · 2016: 1 · 2014: 2 · 2013: 2 · 2012: 1
- FWCI
- 0.56
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- International Journal of Forest Engineering (publishedVersion)
- Topics
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Forest Biomass Utilization and Management
- Life Sciences › Agricultural and Biological Sciences › Forestry › Forest ecology and management
- Life Sciences › Agricultural and Biological Sciences › Forestry › Forest Management and Policy
- Keywords
- stump height, feller-buncher, chainsaw felling, terrain slope, stump diameter, tree species, clear-cutting, subalpine fir, Picea glauca, Pseudotsuga menziesii, wood waste
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effect of Ground Slope, Stump Diameter, and Species on Stump Height for Feller-Buncher and Chainsaw Felling. https://app.cochat.ai/papers/10.1080/14942119.2005.10702517
- The paper
- Han, H.-S., & Renzie, C. (2005). Effect of Ground Slope, Stump Diameter, and Species on Stump Height for Feller-Buncher and Chainsaw Felling. International Journal of Forest Engineering. https://doi.org/10.1080/14942119.2005.10702517
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.