The DOI matches its Crossref record; 10 of the 10 references it cites were found in a registry or an index.
The hardness of solids
Open accessAbstract
This review is concerned with the basic physical meaning of hardness. It is shown that indentation hardness of ductile materials is essentially a measure of their plastic properties. With brittle solids the high hydrostatic pressures around the deformed region are often sufficient to inhibit brittle fracture. Under these conditions both indentation and scratch hardness are essentially a measure of the plastic rather than the brittle properties of the solid. This provides a simple physical basis for the Mohs scratch hardness scale
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
The Deformation and Ageing of Mild Steel: III Discussion of Results
Hall, E. O. (1951) · Proceedings of the Physical Society. Section B · doi:10.1088/0370-1301/64/9/303 · Cited by 7,872
The Mathematical Theory Of Plasticity
Hill, R. (1998) · doi:10.1093/oso/9780198503675.001.0001 · Cited by 7,830
The Friction and Lubrication of Solids
Bowden, F. P., Tabor, D., & Palmer, F. (1951) · American Journal of Physics · doi:10.1119/1.1933017 · Cited by 5,890
Self-citationTabor, D. (2000) · doi:10.1093/oso/9780198507765.001.0001 · Cited by 3,118
Self-citationThe correlation of indentation experiments
Johnson, K. L. (1970) · Journal of the Mechanics and Physics of Solids · doi:10.1016/0022-5096(70)90029-3 · Cited by 1,401
Micro-indentation hardness testing
Mott, B. W. (1956) · Butterworths Scientific Publications eBooks · Cited by 621
Variation of Hardness of Metals with Grain Size
Hall, E. O. (1954) · Nature · doi:10.1038/173948b0 · Cited by 327
Anisotropy in the hardness of single crystals
Brookes, C. A., O’Neill, J. B., & Redfern, B. A. W. (1971) · Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences · doi:10.1098/rspa.1971.0055 · Cited by 244
The direct measurement of the strength of metals on a sub-micrometre scale
Gane, N. (1970) · Proceedings of the Royal Society of London A Mathematical and Physical Sciences · doi:10.1098/rspa.1970.0122 · Cited by 123
The indentation of materials by wedges
Hirst, W., & Howse, M. G. J. W. (1969) · Proceedings of the Royal Society of London A Mathematical and Physical Sciences · doi:10.1098/rspa.1969.0126 · Cited by 119
Cited by
Scaling, dimensional analysis, and indentation measurements
Cheng, Y.-T., & Cheng, C.-M. (2004) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2004.05.001 · Cited by 1,061
Direct observation of frictional contacts: New insights for state-dependent properties
Dieterich, J. H., & Kilgore, B. D. (1994) · pure and applied geophysics · doi:10.1007/bf00874332 · Cited by 959
Chen, H., Ling, M., Hencz, L., Ling, H. Y., Li, G., Lin, Z., Liu, G., & Zhang, S. (2018) · Chemical Reviews · doi:10.1021/acs.chemrev.8b00241 · Cited by 958
Hard amorphous (diamond-like) carbons
Robertson, J. (1991) · Progress in Solid State Chemistry · doi:10.1016/0079-6786(91)90002-h · Cited by 787
Mechanical properties of hybrid organic–inorganic materials
Mammeri, F., Bourhis, E. L., Rozes, L., & Sanchez, C. (2005) · Journal of Materials Chemistry · doi:10.1039/b507309j · Cited by 512
Metadata
- Authors
- Tabor, D.
- Venue
- Reviews of Physics in Technology
- Publisher
- IOP Publishing
- Published
- 1970-01-01
- Volume
- 1
- Issue
- 3
- Pages
- 145-179
- ISSN
- 0034-6683 (ISSN-L)
- OpenAlex
- W2003366574
- Cited by
- 636
- References
- 10
- FWCI
- 7.79
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The hardness of solids. https://app.cochat.ai/papers/10.1088/0034-6683/1/3/i01
- The paper
- Tabor, D. (1970). The hardness of solids. Reviews of Physics in Technology. https://doi.org/10.1088/0034-6683/1/3/i01
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.