The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Direct 3D powder printing of biphasic calcium phosphate scaffolds for substitution of complex bone defects
Open accessAbstract
The 3D printing technique based on cement powders is an excellent method for the fabrication of individual and complex bone substitutes even in the case of large defects. The outstanding bone remodeling capacity of biphasic calcium phosphates (BCPs) containing hydroxyapatite (HA) as well as tricalcium phosphate (TCP) in varying ratios makes the adaption of powder systems resulting in BCP materials to this fabrication technique a desirable aim. This study presents the synthesis and characterization of a novel powder system for the 3D printing process, intended for the production of complexly shaped BCP scaffolds by a hydraulic setting reaction of calcium carbonate and TCP with phosphoric acid. The HA/TCP ratio in the specimens could be tailored by the calcium/phosphate ratio of the starting powder. The scaffolds could be fabricated with a dimensional accuracy of >96.5% and a minimal macro pore size of 300 µm. Independent of the phase composition the printed specimens showed a microporosity of approximately 68%, while the compressive strength strongly depended on the chemical composition and increased with rising TCP content in the scaffolds to a maximum of 1.81 MPa. Post-treatment of the scaffolds with a polylactic-co-glycolic acid-solution enhanced the mechanical properties by a factor of 8. In vitro studies showed that all BCP scaffolds were cytocompatible and enhanced the cell viability as well as the cell proliferation, as compared with pure TCP. Cell proliferation is even better on BCP when compared to HA and cell viability is in a similar range on these materials.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
The compressive behavior of bone as a two-phase porous structure
Carter, D., & Hayes, W. (1977) · The Journal of Bone & Joint Surgery · doi:10.2106/00004623-197759070-00021 · Cited by 2,001
Cited by
Additive Manufacturing of Ceramics: Issues, Potentialities, and Opportunities
Zocca, A., Colombo, P., Gomes, C. M., & Günster, J. (2015) · Journal of the American Ceramic Society · doi:10.1111/jace.13700 · Cited by 1,115
3D Printing of Scaffolds for Tissue Regeneration Applications
Do, A., Khorsand, B., Geary, S. M., & Salem, A. K. (2015) · Advanced Healthcare Materials · doi:10.1002/adhm.201500168 · Cited by 949
Three-dimensional (3D) printed scaffold and material selection for bone repair
Zhang, L., Yang, G., Johnson, B. N., & Jia, X. (2019) · Acta Biomaterialia · doi:10.1016/j.actbio.2018.11.039 · Cited by 865
Shirazi, S. F. S., Gharehkhani, S., Mehrali, M., Yarmand, H., Metselaar, H. S. C., Adib Kadri, N., & Osman, N. A. A. (2015) · Science and Technology of Advanced Materials · doi:10.1088/1468-6996/16/3/033502 · Cited by 755
Recent advances in bioprinting techniques: approaches, applications and future prospects
Li, J., Chen, M., Fan, X., & Zhou, H. (2016) · Journal of Translational Medicine · doi:10.1186/s12967-016-1028-0 · Cited by 608
Metadata
- Authors
- Castilho, M., Moseke, C., Ewald, A., Gbureck, U., Groll, J., Pires, I., Teßmar, J., & Vorndran, E.
- Venue
- Biofabrication
- Publisher
- IOP Publishing
- Published
- 2014-01-15
- Volume
- 6
- Issue
- 1
- Pages
- 015006
- ISSN
- 1758-5082 (ISSN-L)
- 1758-5090
- OpenAlex
- W2057422405
- Cited by
- 211
- References
- 1
- FWCI
- 11.42
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Direct 3D powder printing of biphasic calcium phosphate scaffolds for substitution of complex bone defects. https://app.cochat.ai/papers/10.1088/1758-5082/6/1/015006
- The paper
- Castilho, M., Moseke, C., Ewald, A., Gbureck, U., Groll, J., Pires, I., Teßmar, J., & Vorndran, E. (2014). Direct 3D powder printing of biphasic calcium phosphate scaffolds for substitution of complex bone defects. Biofabrication. https://doi.org/10.1088/1758-5082/6/1/015006
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.