The DOI matches its Crossref record.
Distributed recycling of waste polymer into RepRap feedstock
Open accessAbstract
Purpose: A low‐cost, open source, self‐replicating rapid prototyper (RepRap) has been developed, which greatly expands the potential user base of rapid prototypers. The operating cost of the RepRap can be further reduced using waste polymers as feedstock. Centralized recycling of polymers is often uneconomic and energy intensive due to transportation embodied energy. The purpose of this paper is to provide a proof of concept for high‐value recycling of waste polymers at distributed creation sites. Design/methodology/approach: Previous designs of waste plastic extruders (also known as RecycleBots) were evaluated using a weighted evaluation matrix. An updated design was completed and the description and analysis of the design is presented including component summary, testing procedures, a basic life cycle analysis and extrusion results. The filament was tested for consistency of density and diameter while quantifying electricity consumption. Findings: Filament was successfully extruded at an average rate of 90 mm/min and used to print parts. The filament averaged 2.805 mm diameter with 87 per cent of samples between 2.540 mm and 3.081 mm. The average mass was 0.564 g/100 mm length. Energy use was 0.06 kWh/m. Practical implications: The success of the RecycleBot further reduces RepRap operating costs, which enables distributed in‐home, value added, plastic recycling. This has implications for municipal waste management programs, as in‐home recycling could reduce cost and greenhouse gas emissions associated with waste collection and transportation, as well as the environmental impact of manufacturing custom plastic parts. Originality/value: This paper reports on the first technical evaluation of a feedstock filament for the RepRap from waste plastic material made in a distributed recycling device.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Tymrak, B. M., Kreiger, M., & Pearce, J. M. (2014) · Materials & Design · doi:10.1016/j.matdes.2014.02.038 · Cited by 1,244
Self-citationUnlocking value for a circular economy through 3D printing: A research agenda
Despeisse, M., Baumers, M., Brown, P., Charnley, F., Ford, S. J., Garmulewicz, A., Knowles, S., Minshall, T. H. W., Mortara, L., Reed-Tsochas, F. P., et al. (2017) · Technological Forecasting and Social Change · doi:10.1016/j.techfore.2016.09.021 · Cited by 529
Life-cycle economic analysis of distributed manufacturing with open-source 3-D printers
Wittbrodt, B. T., Glover, A. G., Laureto, J., Anzalone, G. C., Oppliger, D., Irwin, J. L., & Pearce, J. M. (2013) · Mechatronics · doi:10.1016/j.mechatronics.2013.06.002 · Cited by 416
Self-citation3D printing filament as a second life of waste plastics—a review
Mikula, K., Skrzypczak, D., Izydorczyk, G., Warchoł, J., Moustakas, K., Chojnacka, K., & Witek-Krowiak, A. (2021) · Environmental Science and Pollution Research · doi:10.1007/s11356-020-10657-8 · Cited by 382
Global value chains from a 3D printing perspective
Laplume, A. O., Petersen, B., & Pearce, J. M. (2016) · Journal of International Business Studies · doi:10.1057/jibs.2015.47 · Cited by 347
Self-citation
Metadata
- Authors
- Baechler, C., DeVuono, M., & Pearce, J. M.
- Venue
- Rapid Prototyping Journal
- Publisher
- Emerald
- Published
- 2013-03-01
- Volume
- 19
- Issue
- 2
- Pages
- 118-125
- ISSN
- 1355-2546 (ISSN-L)
- OpenAlex
- W2161153826
- Cited by
- 269
- References
- 0
- FWCI
- 28.00
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Distributed recycling of waste polymer into RepRap feedstock. https://app.cochat.ai/papers/10.1108/13552541311302978
- The paper
- Baechler, C., DeVuono, M., & Pearce, J. M. (2013). Distributed recycling of waste polymer into RepRap feedstock. Rapid Prototyping Journal. https://doi.org/10.1108/13552541311302978
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.