The DOI matches its Crossref record; 27 of the 27 references it cites were found in a registry or an index.
Life-cycle economic analysis of distributed manufacturing with open-source 3-D printers
Open accessAbstract
The recent development of open-source 3-D printers makes scaling of distributed additive-based manufacturing of high-value objects technically feasible and offers the potential for widespread proliferation of mechatronics education and participation. These self-replicating rapid prototypers (RepRaps) can manufacture approximately half of their own parts from sequential fused deposition of polymer feedstocks . RepRaps have been demonstrated for conventional prototyping and engineering, customizing scientific equipment, and appropriate technology-related manufacturing for sustainable development . However, in order for this technology to proliferate like 2-D electronic printers have, it must be economically viable for a typical household. This study reports on the life-cycle economic analysis (LCEA) of RepRap technology for an average US household. A new low-cost RepRap is described and the costs of materials and time to construct it are quantified. The economic costs of a selection of 20 open-source printable designs (representing less than 0.02% of those available), are typical of products that a household might purchase, are quantified for print time, energy, and filament consumption and compared to low and high Internet market prices for similar products without shipping costs. The results show that even making the extremely conservative assumption that the household would only use the printer to make the selected 20 products a year the avoided purchase cost savings would range from about $300 to $2000/year. Assuming the 25 h of necessary printing for the selected products is evenly distributed throughout the year these savings provide a simple payback time for the RepRap in 4 months to 2 years and provide an ROI between >200% and >40%. As both upgrades and the components that are most likely to wear out in the RepRap can be printed and thus the lifetime of the distributing manufacturing can be substantially increased the unavoidable conclusion from this study is that the RepRap is an economically attractive investment for the average US household already. It appears clear that as RepRaps improve in reliability, continue to decline in cost and both the number and assumed utility of open-source designs continues growing exponentially, open-source 3-D printers will become a mass-market mechatronic device.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Next Generation Science Standards: For States, By States
(2013) · National Academies Press eBooks · doi:10.17226/18290 · Cited by 1,321
(2012) · Cited by 1,272
Fabricated: The New World of 3D Printing
Lipson, H., & Kurman, M. (2013) · Cited by 1,032
FAB: The Coming Revolution on Your Desktop--from Personal Computers to Personal Fabrication
Gershenfeld, N. (2005) · Works - Scholarship, Research, & Creative Expression (Swarthmore College) · Cited by 862
A Simple, Low-Cost Conductive Composite Material for 3D Printing of Electronic Sensors
Leigh, S. J., Bradley, R. J., Purssell, C. P., Billson, D. R., & Hutchins, D. A. (2012) · PLoS ONE · doi:10.1371/journal.pone.0049365 · Cited by 787
RepRap – the replicating rapid prototyper
Jones, R., Haufe, P., Sells, E., Iravani, P., Olliver, V., Palmer, C., & Bowyer, A. (2011) · Robotica · doi:10.1017/s026357471000069x · Cited by 736
Additive layered manufacturing: sectors of industrial application shown through case studies
Petrovic, V., Vicente Haro Gonzalez, J., Jordá Ferrando, O., Delgado Gordillo, J., Ramón Blasco Puchades, J., & Portolés Griñan, L. (2011) · International Journal of Production Research · doi:10.1080/00207540903479786 · Cited by 676
Integrated 3D-printed reactionware for chemical synthesis and analysis
Symes, M. D., Kitson, P. J., Yan, J., Richmond, C. J., Cooper, G. J. T., Bowman, R. W., Vilbrandt, T., & Cronin, L. (2012) · Nature Chemistry · doi:10.1038/nchem.1313 · Cited by 617
Building Research Equipment with Free, Open-Source Hardware
Pearce, J. M. (2012) · Science · doi:10.1126/science.1228183 · Cited by 561
Self-citationThree-dimensional tissue fabrication
Liu Tsang, V., & Bhatia, S. N. (2004) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2004.05.001 · Cited by 519
Cited by
Tymrak, B. M., Kreiger, M., & Pearce, J. M. (2014) · Materials & Design · doi:10.1016/j.matdes.2014.02.038 · Cited by 1,244
Self-citationDirect digital manufacturing: definition, evolution, and sustainability implications
Chen, D., Heyer, S., Ibbotson, S., Salonitis, K., Steingrímsson, J. G., & Thiede, S. (2015) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2015.05.009 · Cited by 498
Bridging topology optimization and additive manufacturing
Zegard, T., & Paulino, G. H. (2016) · Structural and Multidisciplinary Optimization · doi:10.1007/s00158-015-1274-4 · Cited by 457
Global value chains from a 3D printing perspective
Laplume, A. O., Petersen, B., & Pearce, J. M. (2016) · Journal of International Business Studies · doi:10.1057/jibs.2015.47 · Cited by 347
Self-citationKreiger, M., & Pearce, J. M. (2013) · ACS Sustainable Chemistry & Engineering · doi:10.1021/sc400093k · Cited by 295
Self-citation
Metadata
- Authors
- Wittbrodt, B. T., Glover, A. G., Laureto, J., Anzalone, G. C., Oppliger, D., Irwin, J. L., & Pearce, J. M.
- Venue
- Mechatronics
- Publisher
- Elsevier BV
- Published
- 2013-09
- Volume
- 23
- Issue
- 6
- Pages
- 713-726
- ISSN
- 0957-4158 (ISSN-L)
- OpenAlex
- W2106365938
- Cited by
- 416
- References
- 27
- FWCI
- 53.41
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Life-cycle economic analysis of distributed manufacturing with open-source 3-D printers. https://app.cochat.ai/papers/10.1016/j.mechatronics.2013.06.002
- The paper
- Wittbrodt, B. T., Glover, A. G., Laureto, J., Anzalone, G. C., Oppliger, D., Irwin, J. L., & Pearce, J. M. (2013). Life-cycle economic analysis of distributed manufacturing with open-source 3-D printers. Mechatronics. https://doi.org/10.1016/j.mechatronics.2013.06.002
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.